• 한국태양에너지학회 논문집
• /
• 제28권2호
• /
• pp.58-63
• /
• 2008

This study has analysed power output characteristics of transparent thin-film PV module depending on incidence angle and azimuth. The experiment results showed power outputs of transparent thin-film PV module applied to full-scale mock up model on slope of $90^{\circ},\;30^{\circ},\;0^{\circ}$ to the south. The simulation results was evaluated power outputs of transparent thin-film PV module depending on incidence angle and azimuth after calibrating the experimental and computed data. As a result. the best power output performance of transparent thin-film PV module was obtained at slope of $30^{\circ}$ to the south, producing the annual power output of 977kWh/kWp. The annual power output data demonstrated that the PV module with a slope of $30^{\circ}$ could produce a 68 % higher power output than that with a slope of $90^{\circ}$ with respect to the inclined slope of the module, Furthermore, the PV module facing south showed a 22 % higher power output than that facing to the east in terms of the angle of the azimuth, Specipically. the varying power output with incidence angle of PV module can be resulted from the influence of incidence angle modifier of glass on PV module. That is, the solar energy transmission can be reduced as an increase of incidence angle of PV module. Therefore, when the inclined slope of the PV module was over $70^{\circ}$ there was a significant reduction of power output, and this was caused by the decrease of solar energy transmission in the transparent thin-film PV module.

• Wind and Structures
• /
• 제19권1호
• /
• pp.59-73
• /
• 2014

This paper presents the results of wind tunnel studies and numerical studies on a '+' plan shaped tall building. The experiment was carried out in an open circuit wind tunnel on a 1:300 scale rigid model. The mean wind pressure coefficients on all the surfaces were studied for wind incidence angle of $0^{\circ}$ and $45^{\circ}$. Certain faces were subjected to peculiar pressure distribution due to irregular formation of eddies caused by the separation of wind flow. Moreover, commercial CFD packages of ANSYS were used to demonstrate the flow pattern around the model and pressure distribution on various faces. k-${\varepsilon}$ and SST viscosity models were used for numerical study to simulate the wind flow. Although there are some differences on certain wall faces, the numerical result is having a good agreement with the experimental results for both wind incidence angle.

• 한국추진공학회지
• /
• 제23권3호
• /
• pp.35-43
• /
• 2019

본 연구에서는 핀-휜이 있는 유로에 위치와 유동 입사각이 다른 가이드 베인을 부착하여 전열 성능 및 압력 강하 특성 변화를 분석하였다. 레이놀즈수가 1400일 때 가이드 베인의 위치와 입사각에 따른 전열 성능과 유동 특성을 수치해석으로 확인하였고, 핀-휜 만 있는 해석 결과와 비교하였다. 수치해석을 수행한 결과, Case 1의 입사각 $0^{\circ}$일 경우에 전열 성능이 최대가 되고 핀-휜 만 있는 유로에 비해 약 5% 향상되었다. Case 2의 입사각 $10^{\circ}$일 경우에 압력 손실이 최소가 되고 약 1.9% 감소하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.387.1-387
• /
• 2002

In this paper, consideration of correlation between normal and random incidence is made by experiment and theory.

• Earthquakes and Structures
• /
• 제8권1호
• /
• pp.185-204
• /
• 2015

This study investigates the impact of the earthquake incident angle on the structural demand and the influence of ground motion selection and scaling methods on seismic directionality effects. The structural demand produced by Non-Linear Time-History Analyses (NLTHA) varies with the seismic input incidence angle. The seismic directionality effects are evaluated by subjecting four three-dimensional reinforced concrete structures to different scaled and un-scaled records oriented along nine incidence angles, whose values range between 0 and 180 degrees, with an increment of 22.5 degrees. The results show that NLTHAs performed applying the ground motion records along the principal axes underestimate the structural demand prediction, especially when plan-irregular structures are analyzed. The ground motion records generate the highest demand when applied along the lowest strength structural direction and a high energy content of the records increases the structural demand corresponding to this direction. The seismic directionality impact on structural demand is particularly important for irregular buildings subjected to un-scaled accelerograms. However, the orientation effects are much lower if spectrum-compatible combinations of scaled records are used. In both cases, irregular structures should be analyzed first with pushover analyses in order to identify the weaker structural directions and then with NLTHAs for different incidence angles.

• Journal of Electrical Engineering and information Science
• /
• 제3권1호
• /
• pp.80-85
• /
• 1998

A theoretical calculation and an optical measurement method of normal-incidence absorption are proposed. By using a waveguide structure, optical interference and the problem of low level signal can be avoided in the measurement of normal-incidence absorption. The oscillator strength of intersubband absorption for a waveguide structure is calculated in Si(001), Si(110), and Ge(001) quantum wells. The polarization angle dependence of the measured and the calculated absorption strength can be obtained with the same waveguide structure, and be compared after normalization. The normal-incidence absorption in Si(110) and Ge(001) quantum wells is shown theoretically, and can be observed in the optical measurement using waveguide structures at the polarization angle of 90$^{\circ}$.

• 한국전자파학회논문지
• /
• 제9권2호
• /
• pp.238-252
• /
• 1998

임의의 편파로서 비스듬한 각도록 입사하는 전자파의경우에 대한 접지돈 유전체층 위에 놓여있는 주기적인 스트립격자 구조에서의 특이한 희절현상을 샘플링 정리와 파수영역 방법을 사용하여 해석하였다. 수치적 결과는 임의의 편파와 TE 및 TM편파가 입사되는 경우에 대하여 각각 Bragg 및 Off-Bragg blazing현상을 확인하고 이에 관하여 논의하였다.

• KIEAE Journal
• /
• 제12권6호
• /
• pp.107-112
• /
• 2012

The purpose of this study is to determine the optimum slat angle of the venetian blind which was applied at an outer skin of a curtain-wall system. The evaluation of the blind slat angle was performed in terms of the comfortable visual environment and decreased energy consumption. The office building prototype was considered for the analysis and simulation variables include application of blind, blind slat angle and dimming control of lighting. The annual energy consumption and incidence rate of discomfort glare were analyzed using EnergyPlus which is developed by the U. S. Department of Energy for the detailed building energy simulation. As a result, it turns out that when the blind (reflectance: 0.5) was installed, the annual energy consumption was greater than that of the base model. However, when the dimming control was applied, the maximum energy saving of 16.3% could be achieved at a slat angle of $0^{\circ}$. In addition, in case of the base model, the incidence rate of discomfort glare was 84%, while the case of the blind with the slat angle of $0^{\circ}$ showed that the incidence rate of discomfort glare was 42.4%. Consequently, the results showed that the slat angle of $55^{\circ}$ with dimming control was the optimum strategy for the comfortable visual environment and decreased energy consumption.

• 한국해안·해양공학회논문집
• /
• 제24권1호
• /
• pp.26-35
• /
• 2012

지금까지 하천 및 해류에서의 지반의 수리저항 특성에 대한 연구는 흐름의 방향을 고려하지 않고 주 흐름방향에 대해서만 고려해 왔다. 최근 왕복류 흐름에 의한 지반의 수리저항특성에 대한 연구결과에 의하면 세립질 및 조립질 시료 모두에서 일방향 흐름보다 왕복류를 고려한 양방향 흐름에서 세굴률이 크게 발생 하는 것으로 나타났다. 그러나 해안구조물이 설치되는 해안 또는 협곡에서 흐름의 방향은 반드시 $180^{\circ}$를 이루지 않으므로 흐름의 입사각이 지반의 수리저항성능에 미치는 영향에 대한 검토가 반드시 필요하다. 이에 흐름방향을 고려할 수 있도록 개선된 수리저항성능 실험기를 이용하여 인공적으로 조성된 점성 세립질 및 점성 조립질 시료에 대하여 $0^{\circ}$, $90^{\circ}$, $135^{\circ}$, $180^{\circ}$의 입사각을 갖는 흐름에 대한 일방향 및 양방향 수리저항성능을 평가하였다. 실험결과 세립질 및 조립질 시료 모두에서 입사각이 커짐에 따라 수리저항성능은 감소하고 세굴률이 증가하는 것으로 나타났다. 압밀압력이 낮은 경우에는 세립토의 수리저항성능이 급격히 떨어지나 압밀압력이 큰 경우에는 조립토의 수리저항성능이 세립토에 비해 약간 더 빠르게 감소하는 것으로 나타났다. 최종적으로는 양방향 흐름일 경우 가장 큰 세굴률이 발생하므로 다양한 흐름방향에 노출되는 구조물의 경우는 양방향 흐름에 대해 수리저항성능을 평가하는 것이 타당한 것으로 판단된다.

• 한국광학회지
• /
• 제14권3호
• /
• pp.321-326
• /
• 2003

WDM광통신의 핵심 소자 중 하나인 파장 가변 레이저를 넓은 파장 영역에서 회절 격자에 대한 입사각의 변화에 따라 연속 가변되는 Littman형과 Littrow 형의 외부 공진기로 구현하였다 회절 격자에 대한 입사각과 회절각이 동일하며 구조가 간단한 Littrow형의 파장 가변 레이저에서, 입사각 49$^{\circ}$를 중심으로 격자를 $\pm$1$^{\circ}$정도 회전시켜 C-밴드 및 L-밴드 영역을 대부분 포함하는 약 80 nm 정도의 가변 범위(1510 nm-1590 nm)를 얻었으며, 특히, 60 nm 범위에서는 주입 전류의 조절 없이 1.5㏈ 미만의 출력 변화를 보임으로써, 광대역 파장 가변 광원으로 적합한 구조임을 확인하였다.