• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 가을 학술발표회 논문집
• /
• pp.441-448
• /
• 1999

The load distribution in a ground anchor is very complex because it involves three different materials(soil, grout, and steel), which sometimes act as composite sections (bonded length) or separately (unbounded length). Therefore it is very hard to understand load transfer mechanism on the anchor. In order to understand the load transfer, it is essential to consider the load distribution In the three different materials. On these purposes, full scale anchor test is planned on the geotechnical site at Sunkyunkwan University Prior to the test, modeling and analyses of the load transfer mechanism were performed on the data from the case histories.

• 한국지반공학회논문집
• /
• 제15권6호
• /
• pp.187-200
• /
• 1999

타이백 앵커 억지 토류벽의 거동을 분석하기위해 광범위한 현장계측자료를 조사하고 이중 한 현장에 대한 유한요소해석을 실시하였다. 특히, 임의 굴착깊이에 대한 벽체변위-앵커자유장-앵커긴장하중 사이의 상관성을 조사하였다. 유한요소해석은 앵커하중과 앵커자유장을 변화시키면서 벽체변위의 증감을 조사하기 위해 실시하였다. 굴착깊이로 정규화시킨 횡방향 벽체 변위와 앵커위치의 상관도를 작성하였으며 임의 굴착깊이에 대한 벽체변위-앵커자유장-앵커긴장하중 사이에 고유한 관계가 설정됨을 확인하였다. 차후 실무차원에서 이를 활용하기 위해서는 더 많은 현장계측자료의 집적과 유한요소해석의 추가적인 실시가 필요하다.

• 한국해양공학회지
• /
• 제27권1호
• /
• pp.59-66
• /
• 2013

A suction anchor is one of the most popular anchors for deepsea floating systems. An anchor used for catenary mooring is predominantly under a horizontal load. In this study, the behavior of a suction anchor installed in cohesionless soil was investigated when the anchor was mainly subjected to a horizontal load induced by a catenary line. In order to study the behavior of the suction anchor, 3D FEM analysis models were developed and analyzed. Depending on the location of the load (padeye), the ultimate horizontal load was monitored. The distributions of the reaction forces around the anchor induced by the seabed were analyzed using the circumferential stress to understand the behavior of the suction anchor under a horizontal load.

• 산업기술연구
• /
• 제21권B호
• /
• pp.195-203
• /
• 2001

The purpose of this study is to estimate ultimate uplift capacity of permanent anchor which was cast into weathered rock. The ultimate uplift capacity was estimated from the load-displacement curve of four different anchors which have different bond length. The creep test was performed for 15minutes under the maximum load of each step in order to understand the load-transfer property of permanent anchor and to decide which anchor to choose. The destruction range of soil due to the changes in load was estimated by installing dial gauge on the ground which was cast into the weathered rock. Ultimately, the study on the behavior of the anchor case into the weathered rock was performed by comparing and analyzing the estimated result of the UUC obtained by the full scale pull out test in the field with the exsting theoretical and practical results of soil and rock anchor.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1434-1441
• /
• 2005

For anchored system applications, each ground anchor is tested after installation and prior to being put into service to loads that exceed the design. This load testing methodology, combined with specific acceptance criteria, is used to verify that the ground anchor can carry the design load without excessive deformations and that the assumed load transfer mechanisms have been properly developed behind the assumed critical failure surface. After acceptance, the ground anchor is stressed to a specified load and the load is locked-off. The two types of load tests conducted during the research program included performance test and creep test which were carried out in accordance with testing procedures by AASHTO(AASHTO 1990) and FHWA(Weatherby 1998) at Samsung-Dong 00 Site. Form the measurements, ultimate load and creep rate of anchors are proposed for straight shaft pressured grouted anchors in waste landfill. The load distribution on the grout was obtained from the measured strain data at each fraction of the ultimate load during the load tests.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.339-346
• /
• 2001

For temporary excavation support in private land area, the strand of ground anchor should be removed In order to get permission to install anchors. The extractable or removable-strand compression anchor system was developed and evaluated by a series of pull-out load tests. Anchor pull-out tests were performed on seven instrumented full-scale low-pressure grouted anchors installed in weathered soil at the Geotechnical Experimentation Site at Sungkyunkwan University, Four anchors are the compression type anchors and three are the tension anchors. Performance test, creep test, and long term relaxation test were performed and presented. Load distributor was developed in order to distribute large compressive stresses in grout.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2003년도 봄 학술발표회 논문집
• /
• pp.545-552
• /
• 2003

For temporary excavation support in a congested urban area, the strand of ground anchor should be removed to get permission of the private land to install anchors. But the strand doesn't need to be removed in the outside city area after use. So the anchor body, tension anchor, is fabricated in-situ. The unbonded length of This anchor has several strands, which wrap only one sheath. When the anchor body is carried into job-site or installed in the bore hole, the sheath is torn easily because it is a very week material. So the grout permeate into the torn sheath. Because of that, the load doesn't transfer to the bond length of ground anchors. It may indicate that load is being transferred along the unbonded length and thus within the potential slip surface assumed for overall stability of the anchored system. The load tests were performed on seven low-pressure grouted anchors installed in weathered soil to verify its problems. Four anchors(Type A) have the unbonded length, which consist of five strands and a week sheath and three anchors(Type B) have strands, which is covered by plastic sheath filled with grease, in the unbonded length. Both anchors are compared with load tests results.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.964-968
• /
• 2010

Ground anchor, commonly referred to as tiebacks or tie-down, is essentially steel elements secured in the ground by cement grout. They are used to provide either lateral or vertical support for various engineered structures, and are effective in all types of soil and rock. However, ground anchor can not be used in soft clay because anchor resistance would not be guaranteed. In this paper, conceptual introduction of the Smart Anchor is presented. The Smart Anchor is a kind of friction type anchor, the load is diffused and applied to the various parts of the distributed bond length, having less impact on the grout strength, and being able to secure necessary anchoring force in relatively soft grounds. This study shows a numerical study of predicting the load transfer of The Smart Anchor in soft clay. A beam-column analysis was performed by a elastic-plastic P-y curves in soft clay.

• 한국산학기술학회논문지
• /
• 제21권10호
• /
• pp.267-273
• /
• 2020

석션 앵커는 비교적 간편한 설치 방식과 높은 안정성으로 인해 부유식 구조물을 고정하기 위한 기초로 사용된다. 최근, 허용 변위가 작은 부유식 구조물이 증가함에 따라, 석션 앵커의 유발 변위 평가에 대한 수요가 높아졌다. 하지만, 기존 석션 앵커의 연구는 앵커 지지력 평가에 초점을 두었으며, 앵커의 변위에 관한 연구는 중점적으로 수행되지 않았다. 특히, 경사진 하중을 받는 석션 앵커의 주된 변위인, 회전 거동을 평가한 연구는 매우 부족한 실정이다. 따라서 본 논문에서는 경사 인발 하중이 작용하는 석션 앵커의 회전 거동을 모형실험을 통해 비교 및 분석 하였다. 모형실험은 센트리퓨지 실험 장비를 사용하였으며, 실험 변수로는 하중의 경사도, 앵커의 크기 및 종횡비가 고려되었다. 하중-회전 변위 곡선을 산정하여, 실험 변수에 따른 석션 앵커의 회전량을 비교하였다. 실험 결과, 석션 앵커의 회전 거동은 하중의 경사도에 큰 영향을 받았으며, 앵커의 크기 및 종횡비에 따른 회전량의 차이는 크지 않았다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.55-60
• /
• 2011

For the bolster type bogie, bolster anchor body connections are proviede to transmit the longitudinal loads for traction or braking between the carbody and the truck. The bolster anchor body connection is generally composed of anchor rod bracket, anchor rod and its fastening devices. The bolster anchor body connection shall be basically capable of withstanding a longitudinal load resulting from excessive braking case or impact. Additionally the north America standard requires that the anchor rod bracket shall be frangible, I.e. the anchor rod bracket shall fail and fall away under load before the carbody structure is damaged since to protect the cabody structure in the event of unexpected accident. This paper describes the shear connection design using the optimized mechanical fasteners in the bolster anchor body connection to satisfy these Northe America requirements.