• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.437-438
• /
• 2008

This paper proposes a 8th-order single loop band-pass sigma-delta modulator that satisfies a wide bandwidth of 6MHz, which is required for a HDTV application. The proposed architecture is based on a simple analog structure that enlarges the noise shaping with a low OSR. In addition, a feedforward scheme is used to relax op-amp performance requirements. The proposed modulator has been simulated using the 0.18um 1.8v TSMC technology. The simulation results show that the bandwidth is 6MHz and SNQR is 70dB.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.8
• /
• pp.1227-1234
• /
• 2013

An analog array with a 1.2 double poly floating gate transistor has been developed with a standard CMOS fabrication process. The programming of each cell by means of an efficient control circuit eliminates the unnecessary erasing operation which has been widely used in conventional analog memories. It is seen that the path of the signal for both the programming and the reading is almost exactly the same since just one comparator supports both operations. It helps to eliminate the effects of the amplifier input-offset voltage problem on the output voltage for the read operation. In the array, there is no pass transistor isolating a cell of interest from the adjacent cells in the array. Instead of the extra transistors, one extra bias voltage, Vmid, is employed. The experimental results from the memory shows that the resolution of the memory is equivalent to the information content of at least six digital cells. Programming/erasing of each cell is achieved with no detectable disturbance of adjacent cells. Finally, the unique shape of the injector structure in a EEPROM is adopted as a cell of analog array. It reduces the programming voltage below the transistor breakdown voltage without any special fabrication process.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.17 no.1
• /
• pp.129-140
• /
• 2017

In this paper, a $4{\times}32$-channel neural recording system capable of acquiring neural signals is introduced. Four 32-channel neural recording ICs, complex programmable logic devices (CPLDs), a micro controller unit (MCU) with USB interface, and a PC are used. Each neural recording IC, implemented in $0.18{\mu}m$ CMOS technology, includes 32 channels of analog front-ends (AFEs), a 32-to-1 analog multiplexer, and an analog-to-digital converter (ADC). The mid-band gain of the AFE is adjustable in four steps, and have a tunable bandwidth. The AFE has a mid-band gain of 54.5 dB to 65.7 dB and a bandwidth of 35.3 Hz to 5.8 kHz. The high-pass cutoff frequency of the AFE varies from 18.6 Hz to 154.7 Hz. The input-referred noise (IRN) of the AFE is $10.2{\mu}V_{rms}$. A high-resolution, low-power ADC with a high conversion speed achieves a signal-to-noise and distortion ratio (SNDR) of 50.63 dB and a spurious-free dynamic range (SFDR) of 63.88 dB, at a sampling-rate of 2.5 MS/s. The effectiveness of our neural recording system is validated in in-vivo recording of the primary somatosensory cortex of a rat.

• ETRI Journal
• /
• v.32 no.2
• /
• pp.214-221
• /
• 2010

Radio frequency (RF) subsampling can be used by radio receivers to directly down-convert and digitize RF signals. A goal of a cognitive radio/software defined ratio (CR/SDR) receiver design is to place the analog-to-digital converter (ADC) as near the antenna as possible. Based on this, a band-pass sampling (BPS) frontend for CR/SDR is proposed and verified. We present a receiver architecture based second-order BPS and signal processing techniques for a digital RF frontend. This paper is focused on the benefits of the second-order BPS architecture in spectrum sensing over a wide frequency band range and in multiband receiving without modification of the RF hardware. Methods to manipulate the spectra are described, and reconstruction filter designs are provided. On the basis of this concept, second-order BPS frontends for CR/SDR systems are designed and verified using a hardware platform.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.192-196
• /
• 2001

This work describes the modeling of cutting process for feedback control based on signal processing in end-milling. Here, cutting force is used to design control model by a variety of schemes which are moving average, ensemble average, peak value, root mean square and analog low-pass filtering. It is expected that each model offers its own peculiar advantage in following cutting force control.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.114-124
• /
• 2011

In this paper, we present a 2 GHz compact analog phase shifter with linear phase-tune characteristic. The compact phase shifter was designed base on a lumped all pass network and implemented using a ceramic substrate fabricated with thin-film technique. For a linear phase-tune characteristic, a capacitance of the varactor diode for a tuning voltage was linearized by connecting series capacitor and subsequently produced an almost linear capacitance change. The inductor and bias circuit in the all pass network was implemented using a spiral inductors for small size, which results in the size reduction to $4\;mm{\times}4\;mm$. In order to measure the phase shifter using the probe station, two CPW pads are included at the input and output. The fabricated phase shifter showed an insertion loss of about 4.2~4.7 dB at 2 GHz band and a total $79^{\circ}$ phase change for DC control voltage from 0 to 5 V, and showed linear phase-tune characteristic as expected in the design.

• Progress in Superconductivity
• /
• v.7 no.1
• /
• pp.46-51
• /
• 2005

We have developed control electronics to operate flux-locked loop (FLL), and analog signal filters to process FLL outputs for 64-channel Double Relaxation Oscillation SQUID (DROS) magnetocardiography (MCG) system. Control electronics consisting of a preamplifier, an integrator, and a feedback, is compact and low-cost due to larger swing voltage and flux-to-voltage transfer coefficients of DROS than those of dc SQUIDs. Analog signal filter (ASF) serially chained with a high-pass filter having a cut-off frequency of 0.1 Hz, an amplifier having a gain of 100, a low-pass filter of 100 Hz, and a notch filter of 60 Hz makes FLL output suitable for MCG. The noise of a preamplifier in FLL control electronics is $7\;nV/{\surd}\;Hz$ at 1 Hz, $1.5\;nV/{\surd}\;Hz$ at 100 Hz that contributes $6\;fT/{\surd}\;Hz$ at 1 Hz, $1.3\;fT/{\surd}\;Hz$ at 100 Hz in readout electronics, and the noise of ASF electronics is $150\;{\mu}V/{\surd}\;Hz$ equivalent to $0.13\;fT/{\surd}\;Hz$ within the range of $1{\sim}100\;Hz$. When DROSs are connected to readout electronics inside a magnetically shielded room, the noise of 64-channel DROS system is $10\;fT/{\surd}\;Hz$ at 1 Hz, $5\;fT/{\surd}\;Hz$ at 100 Hz on the average, low enough to measure human MCG.

• Journal of IKEEE
• /
• v.19 no.1
• /
• pp.87-93
• /
• 2015

In this paper, a $145{\mu}W$, 87dB SNR, Low power 3rd order Sigma-Delta Modulator with Op-amp sharing is proposed. Conventional architecture with analog path and digital path is improved by adding a delayed feed -forward path for disadvantages that coefficient value of the first integrator is small. Proposed architecture has a larger coefficient value of the first integrator to remove the digital path. Power consumption of proposed architecture using op-amp sharing is lower than conventional architecture. Simulation results for the proposed SDM designed in $0.18{\mu}m$ CMOS technology with power supply voltage 1.8V, signal bandwidth 20KHz and sampling frequency 2.8224MHz shows SNR(Signal to Noise Ratio) of 87dB, the power consumption of $145{\mu}W$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.1
• /
• pp.160-165
• /
• 2014

In this study, an efficiency test was performed by fabricating MEMS (Micro Electro Mechanical Systems) based 3-axis acceleration sensor modules and an earthquake monitoring system was composed. Data acquisition device (NI-9239) with a 24bit ADC (Analog to Digital Converter) was used for improving the performance of 3-axis acceleration sensor modules and filtered data (100Hz Low Pass Filter) was used for reducing noises. Also this paper focused on detecting meaningful vibration in the building by developing the earthquake monitoring software. If vector sum of 3-axis acceleration is greater than the preset value, the value will be recorded and saved to the file.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.130-137
• /
• 2013

This paper presents analog front-end(AFE) circuits for bio-potential measurement. The proposed AFE is composed of IA(instrument amplifier), BPF(band-pass filter), VGA(variable gain amplifier) and SAR(successive approximation register) type ADC. The low gm(LGM) circuits with current division technique and Miller capacitance with high gain amplifier enable IA to implement on-chip AC-coupling without external passive components. Spilt capacitor array with capacitor division technique and asynchronous control make the 12-b ADC with low power consumption and small die area. The total current consumption of proposed AFE is 6.3uA at 1.8V.