• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.11
• /
• pp.1005-1013
• /
• 2010

This study was conducted to assess the spray control of flash boiling with mixed fuel in consideration of HCCI (Homogeneous Charge Compression Ignition) engine condition. Mixed fuel existing in two phase regions can control the process of mixture formation under low temperature and density by using the spray resulting from flash boiling which is able to induce rapid evaporation of fuel spray as well as the evaporation of high boiling point component. Because HCCI engine injects the fuel early under ambient conditions, it can facilitate the chemical control of ignition combustion and physical control such as breakup and atomization of liquid fuel by flash boiling of mixed fuel which consists of highly ignitable light oil and highly volatile gasoline. This study was conducted by performing video processing after selected composition and molar fraction of the mixed fuel as major parameters and photographed Schlieren image and Mie scattered light corresponding to the flash boiling phenomenon of the fuel spray that was injected inside a constant volume vessel. It was found that flash boiling causes significant changes in the spray structure under relatively low temperature and density. Thus, we analyzed that the flash boiling spray can be used for HCCI combustion by controlling the mixture formation at the early fuel injection timing.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.58-64
• /
• 2007

As the concerns regarding global worming were increased, the pressure of greenhouse gas(GHG) emission reduction on mobile source was also increased. Carbon dioxides contribute over 90% of total GHG emission and the mobile source occupies about 20% of this $CO_2$ emission. Therefore automotive exhaust is suspected to be one of the major reasons of the rapid increase in greenhouse effect gases in ambient air. In this study, in order to investigate $CO_2$ emission characteristics from gasoline passenger cars(PC), which is the most dominant vehicle type in Korea, 106 vehicles were tested on the chassis dynamometer. $CO_2$ emissions and fuel efficiency were measured. The emission characteristics by displacement, gross vehicle weight, vehicle speed and CVS-75/vehicle speed mode were discussed. Test modes were vehicle speed modes and CVS-75 mode that have been used to develop emission factors and to regulate for light-duty vehicle in Korea. It was found that $CO_2$ emissions showed higher large displacement, heavy gross vehicle weight, low vehicle speed and CVS-75 mode than small displacement, light gross vehicle weight, high vehicle speed and vehicle speed mode, respectively. From these results, correlation between $CO_2$ emission and fuel efficiency was also determined. The results of this study will contribute to domestic greenhouse gas emissions calculation and making the national policy for climate change.

• Fisheries and Aquatic Sciences
• /
• v.26 no.8
• /
• pp.500-513
• /
• 2023

The effects of prolonged photoperiod (additional night lighting) were investigated on the production of Ocimum basilicum (lemon basil) and fish/crayfish raised in a nutrient film technique aquaponic system. Hybrid lemon fin barb and red claw crayfish juveniles were co-cultured with O. basilicum and subjected to 12 h of ambient natural daylight and additional 0, 4, 8, and 12 h of night lighting for 14 weeks (two batches of 7 weeks each). The water quality parameters and the performance characteristics of the fish/crayfish/plant were evaluated, and the nutri- ent uptake (nitrogen, phosphorus, and potassium) in the system by the three organisms was also measured. The fish growth performance showed no significant differences (p > 0.05) in all the growth parameters measured across the treatments. The body proximate and nitrogen, phosphate, and potassium (NPK) composition of the fish and crayfish were not significantly (p > 0.05) different across the treatments. Similarly, there was no significant difference (p > 0.05) in the NPK uptake by the fish and crayfish across the treatments. The plant growth performance showed that there were no significant (p > 0.05) differences in the plant growth parameters measured, except for % plant height gained in the 12 h-light treatment (403.2 ± 26.0%) which was significantly (p < 0.05) higher than other treatments and cycles. Hence, this study demonstrat- ed that varying supplementary night lighting has no significant effect on the growth performance of O. basilicum, hybrid lemon fin barb, and red claw crayfish. This study, therefore, suggests that supplementary night lighting should not be considered for O. basilicum production as it does not significantly improve the performance characteristics of the plant nor the fish co-cultured with it in a polyculture aquaponic system.

• Korean Journal of Ecology and Environment
• /
• v.46 no.4
• /
• pp.588-595
• /
• 2013

This study investigated the influence of temperature and $CO_2$ increase on phytoplankton growth and community structure during cold water season (spring) in Lake Paldang, Korea. Four experimental treatments of temperature and $CO_2$ manipulation were prepared in the laboratory batch culture: (1) Control; ambient low temperature ($6{\pm}2^{\circ}C$) and low $CO_2$ (air level, $400mgL^{-1}$), (2) T1; low temperature and high $CO_2$ ($800mgL^{-1}$), (3) T2; high temperature ($20{\pm}2^{\circ}C$) and low $CO_2$, (4) T3; high temperature and high $CO_2$. Algal growth experiment was carried out for 10 days under the light intensity of $70{\mu}mol\;m^{-2}s^{-1}$ (L :D=24 : 0). The level of pH decreased in both T1 and T3, due to dissolution of added $CO_2$. The dominant phytoplankton species of ambient water, Cyclotella meneghiniana succeeded to Fragilaria capucina var. gracilis in high-temperature treatment groups (T2 and T3). Cyanobacteria were very rare at the beginning of the experiment, while Oscillatoria limnetica appeared in only high-temperature groups (T2 and T3) at $6{\sim}7^{th}$ day. $CO_2$ addition in ambient temperature (T1) induced the highest phytoplankton growth, and thereby producing the highest average cell density of $3.27{\pm}0.33\;10^4\;cells\;mL^{-1}$, followed by T2 ($2.65{\pm}0.26\;10^4\;cells\;mL^{-1}$), T3 ($2.09{\pm}0.16\;10^4\;cells\;mL^{-1}$), and Control ($1.86{\pm}0.13\;10^4\;cells\;mL^{-1}$) (F=7.167, p=0.000). In summary, temperature increase changed the phytoplankton community structure and $CO_2$ increase promoted the phytoplankton growth during the cold spring season in Lake Paldang, suggesting a potential effect of climate change on freshwater phytoplankton.

• Atmosphere
• /
• v.25 no.1
• /
• pp.185-191
• /
• 2015

Ambient measurements of aerosol light absorption (${\sigma}_a$) and scattering coefficients (${\sigma}_s$) were done at Gosan climate observatory during summer 2008 using a 3-wavelength photoacoustic soot spectrometer (PASS). PASS was deployed photoacoustic method for light absorption and integrated nephelometry for light scattering measurements. The ${\sigma}_a$ and ${\sigma}_s$ from PASS were compared with those from co-located aethalometer and nephelometer measurements. The aethalometer measurements of ${\sigma}_a$ correlated reasonably well with photoacoustic measurements, but the slope of the linear fitting line indicated the PASS measurement values of ${\sigma}_a$ were larger by a factor of 1.53. The nephelometer measurement values of ${\sigma}_s$ correlated very well with PASS measurements of ${\sigma}_s$, with a slope of 1.12 and a small offset. Comparing to the aethalometer measurements, the photoacoustic measurements of ${\sigma}_a$ didn't exhibit a significant (i.e., the ratio between aethalometer and PASS increased) change with increasing relative humidity (RH). The ratio of ${\sigma}_s$ between nephelometer and PASS increased with increasing RH, especially when the RH increased beyond 80%. This apparent increase in ${\sigma}_s$ with RH may be due to the contribution of hygroscopic growth of aerosols.

• Journal of Bio-Environment Control
• /
• v.9 no.3
• /
• pp.171-178
• /
• 2000

Gross photosynthetic rats of leaves of hydroponically grown cucumber plants(Cucumis sativus L. cv. Guwoosalichungjang) were measured under various conditions of photosynthetic photon flux(PPF), ambient $CO_2$ concentration, air temperature and leaf nitrogen contents. Light compensation point of leaf photosynthesis appeared to be in the range of 10~20$\mu$mol.m$^{-2}$ .s$^{-1}$ and light saturation point be above 1000$\mu$mol.m$^{-2}$ .s$^{-1}$ . Gross photosynthetic rates increased persistently and asymptotically as air temperature rose from 12$^{\circ}C$ to 32$^{\circ}C$. However, there were only small differences in gross photosynthetic rates in the range of 24-32$^{\circ}C$, so that the range seemed to be optimal for photosynthesis of cucumber plants at the condition of $CO_2$ concentration of 400$\mu$mol.mol$^{-1}$ and PPF of around 400$\mu$mol.m$^{-2}$ .s$^{-1}$ . $CO_2$ compensation point of leaf photosynthesis appeared to be in the range of 20-40$\mu$mol.mol$^{-1}$ and $CO_2$ saturation point be above 1200$\mu$mol.mol$^{-1}$ . Gross photosynthetic rates increased sigmoidally as leaf nitrogen content increased. These environmental factors interacted synergistically to enhance gross photosynthetic rate, so that the rate increased multiplicatively s level of one factor increased progressively with higher levels of he other factors. Mathematical models wer developed to estimate the gross photosynthetic rate in accordance with the variations of these environmental factors. These modes can be used not only to explain he variation of growth or yield of cucumber plants under different environmental conditions but also as building blocks of plant growth model or expert system of cucumber plants.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.22 no.1
• /
• pp.53-66
• /
• 1980

The research work is concerned with the analytical and experimental studies on the heat transfer phenomenon around the underground concrete digester used for biogas production Systems. A mathematical and computational method was developed to estimate heat losses from underground cylindrical concrete digester used for biogas production systems. To test its feasibility and to evaluate thermal parameters of materials related, the method was applied to six physical model digesters. The cylindrical concrete digester was taken as a physical model, to which the model,atical model of heat balance can be applied. The mathematical model was transformed by means of finite element method and used to analyze temperature distribution with respect to several boundary conditions and design parameters. The design parameters of experimental digesters were selected as; three different sizes 40cm by 80cm, 80cm by 160cm and l00cm by 200cm in diameter and height; two different levels of insulation materials-plain concrete and vermiculite mixing in concrete; and two different types of installation-underground and half-exposed. In order to carry out a particular aim of this study, the liquid within the digester was substituted by water, and its temperature was controlled in five levels-35。 C, 30。 C, 25。 C, 20。C and 15。C; and the ambient air temperature and ground temperature were checked out of the system under natural winter climate conditions. The following results were drawn from the study. 1.The analytical method, by which the estimated values of temperature distribution around a cylindrical digester were obtained, was able to be generally accepted from the comparison of the estimated values with the measured. However, the difference between the estimated and measured temperature had a trend to be considerably increased when the ambient temperature was relatively low. This was mainly related variations of input parameters including the thermal conductivity of soil, applied to the numerical analysis. Consequently, the improvement of these input data for the simulated operation of the numerical analysis is expected as an approach to obtain better refined estimation. 2.The difference between estimated and measured heat losses was shown to have the similar trend to that of temperature distribution discussed above. 3.It was found that a map of isothermal lines drawn from the estimated temperature distribution was very useful for a general observation of the direction and rate of heat transfer within the boundary. From this analysis, it was interpreted that most of heat losses is passed through the triangular section bounded within 45 degrees toward the wall at the bottom edge of the digesten Therefore, any effective insulation should be considered within this region. 4.It was verified by experiment that heat loss per unit volume of liquid was reduced as the size of the digester became larger For instance, at the liquid temperature of 35˚ C, the heat loss per unit volume from the 0. 1m$^3$ digester was 1, 050 Kcal/hr m$^3$, while at for 1. 57m$^3$ digester was 150 Kcal/hr m$^3$. 5.In the light of insulation, the vermiculite concrete was consistently shown to be superior to the plain concrete. At the liquid temperature ranging from 15。 C to 350 C, the reduction of heat loss was ranged from 5% to 25% for the half-exposed digester, while from 10% to 28% for the fully underground digester. 6.In the comparison of heat loss between the half-exposed and underground digesters, the heat loss from the former was fr6m 1,6 to 2, 6 times as much as that from the latter. This leads to the evidence that the underground digester takes advantage of heat conservation during winter.

• Journal of Korean Society for Geospatial Information Science
• /
• v.22 no.4
• /
• pp.63-69
• /
• 2014

Due to population growth and urban development in construction technology has expanded living space, underground construction as public transport as has been extended to the ground and underground urban traffic congestion increases. This underpass Stations sphere of influence this development was the center of the living space, space-time became a cultural space. However underpass ground space and time and space are enormous difficulties in contrast visibility due to smoke when light levels are low fire occurs, momentary loss of judgment errors due to a sense of orientation, rapid diffusion and ambient oxygen deficiency due to acquisition limitations, such as the Open resulting in property damage and personal injury. The purpose of this study is to analyze the existing system with respect to the address of the underground shopping center and system for presenting an address to the underground shopping mall in the basement of the straight and circular in connection with the street name address. Also can be known only to evacuate their citizens to address the position in the event of a fire inside the basement through the underground shopping mall address standardization system, the fire department only address exact location is being judged will be identified.

• Archives of design research
• /
• v.17 no.2
• /
• pp.5-14
• /
• 2004

Introducing human capacities of control and sensation which have been overlooked into Human-Computer Interaction(HCI), Ubiquitous computing, Augmented Reality and others have been researched recently. New vision of HCI has embodied in Tangible User Interface(TUI). TUI allows users to grasp and manipulate bits with everyday physical object and architectural surface and also TUI enables user to be aware of background object at the periphery of human perception using ambient display media such of light, sound, airflow and water movement. Tangibles, physical object which constitutes TUI system, is the physical object embodied digital bit. Tangibles is not only input device but also the configuration of computing. To get feedback of computing result, user controls the system with Tangibles as action and the system represents reaction in response to User's action. User appreciates digital representation (sound, graphic information) and physical representation (form, size, location, direction etc.) for reaction. TUI's characters require the consideration about both user's action and system's reaction. Therefore we have to need the method to be concerned about physical object and interaction which can be combined with action, reaction and feedback.

• Journal of Korea Society of Industrial Information Systems
• /
• v.11 no.4
• /
• pp.82-92
• /
• 2006

In the field of image recognition, research on face recognition has recently attracted a lot of attention. The most important step in face recognition is automatic eye detection researched as a prerequisite stage. Existing eye detection methods for focusing on the frontal face can be mainly classified into two categories: active infrared(IR)-based approaches and image-based approaches. This paper proposes an eye region detection method in non-frontal faces. The proposed method is based on the edge--based method that shows the fastest computation time. To extract eye region in non-frontal faces, the method uses edge orientationhistogram of the global region of faces. The problem caused by some noise and unfavorable ambient light is solved by using proportion of width and height for local information and relationship between components for global information in approximately extracted region. In experimental results, the proposed method improved precision rates, as solving 3 problems caused by edge information and achieves a detection accuracy of 83.5% and a computational time of 0.5sec per face image using 300 face images provided by The Weizmann Institute of Science.