• Journal of Welding and Joining
• /
• 제5권3호
• /
• pp.19-27
• /
• 1987

This paper presents the weldability for cold pressure but welding method in junction of dissimilar metals each other. Although the weldability between the same aluminium metal plate welding has been studied, the study of itthe rod of aluminium and coper has not fully been investigated. The purpose is to suggest the optimal conditions on the rod of those under above method. To obtain the optimal conditions, associated experiments were performed in a various welding parameters. Consequently, it was proved that the mechanical properties such as tensile strength, hardness and bending strength could be obtained excellent particularly under the welding conditions; pressure is $(32~39) {\times} 10^3/kg/cm^2$, time is beyond 70 seconds, stage is higher than fifth stage.

• Design & Manufacturing
• /
• 제2권5호
• /
• pp.34-38
• /
• 2008

It was investigated that two rods of aluminium can be welded by hot extru-pressure welding method with stepped welding dies, and that the welding pressure on the welding surface were analyzed by computer simulation according to the stepped shapes of welding dies. It was known by computer simulation that welding pressure on the welding section of rods welded using stepped welding dies. And it was known by experime- nts that two rods of aluminium can be welded on the end sections by hot pressure welding method using stepped welding dies without relative rotational movement of contacted aluminium rods needed for the purpose of friction heating and pressure.

• 한국자동차공학회논문집
• /
• 제22권1호
• /
• pp.29-35
• /
• 2014

This paper aims to obtain the effect of lightweight on Radius rod. The response surface method used in the paper is the statistical method. Optimization method is performed with the Radius rod using the lightweight material. Structural analysis is executed by using the ANSYS program to find static and dynamic responses. From this study result, it is verified that the response surface method has the advantage of optimum value in comparison with other optimization methods. The analysis is also performed by response surface method to derive optimal design values. Steel model and aluminium initial model are obtained by finite element analysis to clarify design criteria and the results are compared with three models each other. The weights can be reduced by optimal design analysis results of these models similar to those of existing products. The quantitative goals in this study can also attained through results of fatigue analyses. The reliability on optimal design of Radius rod can be improved by use of structural and fatigue analysis results.

• 한국기계가공학회지
• /
• 제8권4호
• /
• pp.54-60
• /
• 2009

Weight reduction of automobile parts has been sought to achieve fuel efficiency and energy conservation. In this study, a shape design procedure is suggested to obtained the lightweight design of an outer tie rod. The developed aluminium Al6082M is selected as a steel-substitute material. Strength assesment and durability are the important design criterion in the structural design of an outer tie rod. This study considers strength and durability in the optimization process. In this study, the kriging interpolation method and trial and error method are adopted to obtain the minimum weight satisfying the strength and durability constraints.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.22-27
• /
• 2018

One problem of the Discrete Element Method is the assumption of a spherical particle shape, which reduces the computing time but significantly limits the application of the DEM to analysis. This limitation can be overcome by a recently developed rigid-rod model. However, the rigid-rod model has an essential problem related with friction: it always contains friction error because of the bumpy surface. To overcome this issue, we suggest a superposed rigid-rod model in this paper. The superposed rigid-rod model is notably consistent with the theoretical value in terms of the velocity and angular velocity after the collision. The estimated error is negligible(less than 2%). Then, the developed model is applied to hopper discharging. The developed model shows no problem in the discharging flow from the hopper.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.206-209
• /
• 2005

It was investigated that two rods of aluminium can be welded by hot extru-pressure welding method with stepped welding dies, and that the welding pressure on the welding surface were analyzed by computer simulation according to the stepped shapes of welding dies. It was known by computer simulation that welding pressure on the welding section of rods welded using stepped welding dies without eccentricity is lowerer than the welding pressure of rods welded using stepped welding dies with eccentricity of welding surface, and that the welding pressure on the welding section of rods using eccentric-inclined stepped welding dies is higher than the welding pressure of rods using stepped welding dies without eccentricity. And it was known by experiments that two rods of aluminium can be welded on the end sections by hot pressure welding method using eccentric-inclined stepped welding dies without relative rotational movement of contacted aluminium rods needed for the purpose of friction heating and pressure.

• Nuclear Engineering and Technology
• /
• 제51권5호
• /
• pp.1345-1354
• /
• 2019

Clogging of sump strainers that filter the recirculation water in containment after a loss-of-coolant accident (LOCA) seriously impedes the continued cooling of nuclear reactor cores. In experiments examining the corrosion of aluminium alloy 6061, a common material in containment equipment, in borated solutions simulating the water chemistry of sump water after a LOCA, we found that Fe-bearing intermetallic particles, which were initially buried in the Al matrix, were progressively exposed as corrosion continued. Their cathodic nature $vis-{\grave{a}}-vis$ the Al matrix provoked continuous trenching around them until they were finally released into the test solution. Such particles released from Al alloy components in a reactor containment after a LOCA will be transported to the sump entrance with the recirculation flow and trapped by the debris bed that typically forms on the strainer surface, potentially aggravating strainer clogging. These Fe-bearing intermetallic particles, many of which had a rod or thin strip-like geometry, were identified to be mainly the cubic phase ${\alpha}_c-Al(Fe,Mn)Si$ with an average size of about $2.15{\mu}m$; 11.5 g of particles with a volume of about $3.2cm^3$ would be released with the dissolution of every 1 kg 6061 aluminium alloy.

• 한국지반공학회논문집
• /
• 제26권8호
• /
• pp.5-14
• /
• 2010

지반모형실험에서 2차원 평면변형률 상태를 모사하기 위해서는 흙을 담을 수 있는 두꺼운 유리 또는 플라스틱 시트의 토조가 필요하며, 이 때 흙과 접촉되는 토조벽면에서의 마찰저항을 최소화 하여야 한다. 하지만, 실제로 이러한 벽면마찰을 완전히 제거할 수는 없다. 본 연구에서는 벽면 마찰저항을 제거하기 위해 다양한 지름을 갖는 알루미늄 봉 지반모델을 도입하고 실내전단시험에 적용하였다. 또한 근거리 사진계측기법을 전단시험에 적용해 유용성을 검증하였다. 그 결과, 근거리 사진계측으로부터 얻은 평균 팽창각은 전단시험의 전단변형률-체적변형률 곡선으로부터 얻는 팽창각에 근접함을 확인할 수 있었다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1997년도 특별강연 및 추계학술발표 개요집
• /
• pp.184-193
• /
• 1997

Aluminium and aluminium alloys have the high electrical and heat conductivity. It gives rise to difficulties for a choice of electrodes material for their contact electric welding. This paper describes the investigations performed to solve the above problem. The purpose of this investigation was to obtain dispersion-hardening alloys by the internal oxidation method, to optimize their contents and treatment modes, to produce electrodes of these alloys and to test them. The strengthing effect of alloys with oxide particles depends on their size stability at high temperatures. Despite of the fact, that oxides are the most stable of all the non-metallic phases their coagulation takes place. Based on the early results, we chose two types of alloys, first No. 1 Cu - 0,4%Al and second No. 2 Cu - 0,2%Be for production of electrodes. These alloys had not additional alloying elements. These alloys were prepared as 1 mm plates and flake-formed 200 m thick, and also No. 1 as a powder of size 100 mkm (received from Korea). The large samples for electrodes were produced by three methods : explosive welding method, dynamic one including the explosion compression of electrode blank and the quasi-dynamic method including the high-speed compression of dense briquest and the further hot extrusion of a rod.

• 소성∙가공
• /
• 제7권1호
• /
• pp.66-71
• /
• 1998

The present study is concerned with the hydrostatic extrusion process of copper-clad aluminium bar to investigate the bonding conditions as well as the basic flow characteristics. Considering the bonding mechanism of bi-metal contact surface as cold pressure welding the normal pressure and the contact surface expansion are selected as process parameters governing the bonding conditions, in this study the critical normal pressure required for the local extrusion-the protrusion of virgin surfaces by the surface expansion at the interface-is obtained using a slip line method and is then used as a criteron for the bonding. A rigid plastic finite element method is used to analyze the steady state extrusion process. The interface profile of bi-metal rod is predicted by tracking the paths of two particles adja-process. The interface profile of bi-metal rod is predicted by tracking the paths of two particles adja-cent to interface surface. The contact surface area ration and the normal pressure along the interface are calculated and compared to the critical normal pressure to check bonding. It is found that the model predictions are generally in good agreement with the experimental observations. The compar-isons of the extrusion pressure and interface profile by the finite element with those by experi-ments are also given.