• 제목/요약/키워드: Aluminium Alloy

검색결과 366건 처리시간 0.024초

Warm Compression of Al Alloy PM Blends

  • Jiang, Z.;Falticeanu, C.L.;Chang, I.T.H.
    • 한국분말야금학회:학술대회논문집
    • /
    • 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
    • /
    • pp.193-194
    • /
    • 2006
  • With the onging trend of weight saving in automobiles, the application of light alloys is increasing. Recently, aluminum powder metallurgy has been the subject of renewed attention due to the combination of lightweight of aluminium and the efficient material utilisation of the powder metallurgical process, which offer attractive benefits to potential end-users. This study is to explore the use of warm compaction process to aluminium powder metallurgy. This paper presents a detailed study of the effect of warm compression and sintering conditions on the resultant microstructures and mechanical properties of Al-Cu-Mg-Si PM blend.

  • PDF

표면처리가 장갑재료의 방호한계에 미치는 영향 (An Effect of surface treatment on a Protection Ballistic Limits in armor material)

  • 손세원;김희재;이두성;홍성희;유명재
    • 한국정밀공학회지
    • /
    • 제20권12호
    • /
    • pp.126-134
    • /
    • 2003
  • In order to investigate the effect of surface treatment in Aluminium alloy and Titanium alloy which are used to armor material during ballistic impact, a ballistic testing was conducted. Anodizing was used to achieve higher surface hardness of Aluminium alloy and Iron plating in PVD(Physical Vapor Deposition) method was used to achieve higher surface hardness of Titanium alloy. Surface hardness test were conducted using a Micro victor's hardness tester. Ballistic resistance of these materials was measured by protection ballistic limit(V-50), a statical velocity with 50% probability penetration. Fracture behaviors and ballistic tolerance, described by penetration modes, are respectfully observed from the results of V-50 test and Projectile Through Plates (PTP) test at velocities greater than V-50. PTP tests were conducted with 0$^{\circ}$obliquity at room temperature using 5.56mm ball projectile. V-50 tests were conducted with 0$^{\circ}$obliquity at room temperature with projectiles that were able to achieve near or complete penetration during PTP tests. Surface hardness, resistance to penetration. and penetration modes of surface treated alloy laminates are compared to those of surface non-treated alloy laminates. A high speed photography was used to analyze the dynamic perforation phenomena of the test materials.

내열마그네슘 합금을 이용한 자동차용 오일팬의 다이캐스팅 공정 연구 (A Study on Die Casting Process of the Automobile Oil Pan Using the Heat Resistant Magnesium Alloy)

  • 신현우;정연준;강승구
    • 한국자동차공학회논문집
    • /
    • 제17권3호
    • /
    • pp.45-53
    • /
    • 2009
  • Die casting process of Mg alloys for high temperature applications was studied to produce an engine oil pan. The aim of this paper is to evaluate die casting processes of the Aluminium oil pan and in parallel to apply new Mg alloy for die casting the oil pan. Temperature distributions of the die and flow pattern of the alloys in cavity were simulated to diecast a new Mg alloy by the flow simulation software. Dies have to be modified according to material characteristics because melting temperature and heat capacity are different. We changed the shape and position of runner, gate, vent hole and overflow by the simulation results. After several trial and error, oil pans of AE44 and MRI153M Mg alloys are produced successfully without defect. Sleeve filling ratio, cavity filling time and shot speed of die casting machine are important parameter to minimize the defect for die casting Magnesium alloy.

분사주조한 입자강화 알루미늄 복합재료의 미세조직 특성 (Characteristics in Microstructure of Particle Reinforced Al Matrix Composites Fabricated by Spray-Cast Forming Process)

  • 박종성;이인우;김명호
    • 한국주조공학회지
    • /
    • 제14권6호
    • /
    • pp.530-540
    • /
    • 1994
  • Aluminium-silicon alloy(JIS AC8A) matrix composites reinforced with SiC particles were fabricated by spray-cast forming process, and the microstructure of powders and preforms produced were studied by using an optical and scanning electron microscopy. SiC particles were co-sprayed by mixed phase injection method during the spray casting process. Most of the composite powders formed by this mixed phase injection method exhibit morphology of particle-embedded type, and some exhibits the morphology of particle attached type due to additional attachment of the SiC particles on the surface of the powders in flight. The preforms deposited were resulted in dispersed type microstructure. The pre-solidified droplets and the deposited preform of SiC-reinforced aluminium alloy exhibit finer equiaxed grain size than that of unreinforced aluminium alloy. Eutectic silicons of granular type are crystallized at the corner of the aluminum grains in the preforms deposited, and some SiC particles seem to act as nucleation sites for primary/eutectic silicon during solidification. Such primary/eutectic silicons seem to retard grain growth during the continued spray casting process. It is envisaged from the microstructural observations for the deposited preform that the resultant distribution of SiC injected particles in the Al-Si microsturcture is affected by the amount of liquid phase in the top part of the preform and by the solidification rate of the preform deposited.

  • PDF

SiC 휘스커 보강 Al6061 복합재료의 통계학적 피로균열진전 수명예측 (Statistical Life Prediction of Fatigue Crack Growth for SiC Whisker Reinforced Aluminium Composite)

  • 권재도;안정주;김상태
    • 대한기계학회논문집
    • /
    • 제19권2호
    • /
    • pp.475-485
    • /
    • 1995
  • In this study, statistical analysis of fatigue data which had obtained from respective 24 fatigue crack, was examined for SiC whisker reinforced aluminium 6061 composite alloy (SiC$_{w}$/A16061) and aluminium 6061 alloy. SiC volume fraction in composite alloy is 25%. The analysis results stress intensity factor range and 0.1 mm fatigue crack initiation life for SiC$_{w}$/A16061 composite & A16061 matrix are the log-normal distribution. And regression analysis by linear model, exponential model and multiplicative model were performed to find out the relationship between fatigue crack growth rate(da/dN) and stress intensity for find out the relationship between fatigue crack growth rate(da/dN) and stress intensity factor range(.DELTA.K) in the SiC$_{w}$/A16061 composite and examine the applicability of Paris' equation to SiC$_{w}$A16061 composite. Also computer simulation was performed for fatigue life prediction of SiC$_{w}$/A16061 composite using the statistical results of this study.udy.

주조용 B390 알루미늄합금의 조직과 기계적 성질에 대한 각종 주조법의 영향 (Effect of Casting Processes on the Microstructures and Mechanical Properties of B390 Aluminium Alloy)

  • 한요섭;이호인;김성수;김정식
    • 한국주조공학회지
    • /
    • 제13권3호
    • /
    • pp.259-267
    • /
    • 1993
  • The effects of casting processes-direct and indirect squeeze casting, permanent mold casting and die casting on the microstructure and mechanical properties were studied for the hypereutectic B390 aluminium alloy. The effects of T5 and T6 heat treatment were also examined. The direct and indirect squeeze casting showed no casting defects such as porosity and shrinkage were observed in permanent mold castings and die castings. The primary silicon phase was refined and homogeneously distributed in the order of indirect squeeze casting, diecasting, direct squeeze casting and permanent mold casting. Depletion of primary silicon phase in die casting surface was disappeared in indirect squeeze casting. Tensile strength of cast and heat treated specimens were increased in the order of direct squeeze casting, permanent mold casting, indirect squeeze casting and die casting. Hardness of indirect squeeze castings was larger than that of other castings. As indirect squeeze casting of B390 aluminium alloy, the time of T6 heat treatment to achieve high strength can be reduced.

  • PDF

프레스에 의한 블랭킹 판재의 응력 해석 (Stress Analysis of Blanking Plate Applied by Press)

  • 조재웅;한문식
    • 한국기계가공학회지
    • /
    • 제7권2호
    • /
    • pp.66-71
    • /
    • 2008
  • The data of the deformation and the stress according to time are studied at upper model of press and lower model of the blanking plate applied by press with the width, length and height of 0.4 m and 0.6 m respectively. The press is pushing downward on the plate fixed at the lower floor. These data are compared and investigated through this study. By using these results, there is the maximum deformation at 4 corners in the lower plate model of aluminium alloy fixed at lower floor. This deformation incase of elapsed time of 0.6 second becomes 4 times as much as in case of elapsed time of 0.2 second. The quantity of deformation at the lower plate model becomes more than at the upper press model to the extent of 10%. At the lower plate model of aluminium alloy, there is the maximum Von-Mises equivalent stress at 4 corners and both sides of middle area on the lower plate model of aluminium alloy. This stress in case of elapsed time of 0.6 second becomes 6 times as much as in case of elapsed time of 0.2 second. The Von-Mises equivalent stress of lower plate model becomes 2 times as much as that of upper press mode.

  • PDF

3차원 원격 스캐너를 이용한 알루미늄 5000 계열의 레이저 용접에서 공정 변수에 따른 용접 특성 분석 (Analysis of Weld Characteristics for Aluminum 5XXX Series Laser Welding Using 3-Dimension Remote Scanner)

  • 김동윤;박영환
    • 한국레이저가공학회지
    • /
    • 제14권2호
    • /
    • pp.1-7
    • /
    • 2011
  • The latest trends of vehicle technology development are fuel efficiency improvement, body designs declining air resistance and lightweight of materials. Especially, as lightened weight of materials makes engine efficient so that vehicles keep the best performance, it is the best way to protect the environment and reduce fuel consumption. In this study, we conducted laser welding by using 3-dimension remote scanner that is 5J32 aluminium alloy. Furthermore, conduction experiment that was 3 times repeated for changing factors such as observing angle, laser power and welding speed. we observed exterior and cross section of weled part and tensile strength. When increasing laser power and decreasing laser speed, tensile strength increased. In order to evaluate factors that affect tensile strength qualitatively we conducted ANOVA. We assumed that the factors are observing angle, laser power and welding speed. Then we found that laser power and laser speed affect tensile strength. We conducted evaluation of weldability of aluminium alloy by above ways.

  • PDF

6N01 Al 합금의 미세조직 및 기계적 성질에 미치는 시효처리의 영향 (Effect of aging treatment on the microstructures and mechanical properties of 6N01 Aluminium alloy)

  • 강민철;구흥서;윤인택;강정윤;김인배
    • 열처리공학회지
    • /
    • 제11권4호
    • /
    • pp.268-273
    • /
    • 1998
  • Effect of aging treatment on the microstructures and mechanical properties of 6N01 Aluminium alloy was investigated by differential scanning calorimetry, transmission electron microscopy, microhardness measurement and tensile test. It was found that the precipitation sequence of 6N01 Aluminium alloy was GP zone ${\rightarrow}$ metastable hexagonal $Mg_2S_i({\beta}^{\prime})$,${\rightarrow}$ equilibrium fcc $Mg_2S_i({\beta})$, and the precipitates at peak aged condition were GP zones and ${\beta}^{\prime}$ phase. Microhardness changes during over aged condition showed very small decrease upon increased aging time. This result was attributed to the very slow transformation rate of ${\beta}^{\prime}$ to ${\beta}$. Maximum hardness(116 Hv) and tensile strength(312.6MPa) with 22.3% elongation were obtained from the specimen aged at $180^{\circ}C$ for 15hrs.

  • PDF

Boron Powder 적용 연료과농 추진제 및 연소 후 생성물의 특성 연구 (Characteristics of Fuel-rich Solid Propellants with Boron Powder and the Combustion Products)

  • 김미리;김정은;길태옥
    • 한국추진공학회지
    • /
    • 제26권1호
    • /
    • pp.12-19
    • /
    • 2022
  • 덕티드 로켓의 가스발생기에 사용되는 추진제는 연료과농 추진제로서, 일반적인 고체 로켓 추진제에 비하여 과량의 금속연료와 소량의 산화제를 포함한다. 본 논문에서는 연료과농 추진제를 제조하기 위하여 보론 분말과 MgAl(Magnesium-Aluminium Alloy)를 적용하였다. 이 금속연료를 적용한 추진제의 특성을 분석하였고, 이를 통하여 최적의 조성을 연구하였다. 추진제의 연소생성물 분석을 통하여 보론 비드가 아닌 미립의 보론 분말로도 가스발생기용 연료과농 추진제가 가능함을 확인하였다.