• Journal of the Korean Society of Safety
• /
• v.6 no.4
• /
• pp.26-33
• /
• 1991

To remove SO$_2$ from flus gas, cupric oxide, manganese oxide and iron oxide were studied with varying loading value. The experiment was carried out in a flow reactor and the reactants were prepared by impregnation method using alumina. The reaction temperature was varied from 30$0^{\circ}C$ to 45$0^{\circ}C$. Experimental results showed that all of these metal oxides were effective on SO$_2$ removal reaction and cupric oxide was the best reactant. The sample with 10wt％ loading value was better reactant than with 20wt％ because in case of 20wt％ loading, metal dispersion on the alumina surface was not uniform. And the SO$_2$ removal efficiency was increased with the reaction temperature.

• Journal of Advanced Technology Convergence
• /
• v.1 no.2
• /
• pp.19-25
• /
• 2022

It is intended to evaluate the performance of the shield after manufacturing a shield with cheap and eco-friendly iron oxide and alumina instead of lead, which is a radiation shielding material. After manufacturing the shield by mixing iron oxide and alumina with gypsum, the performance is evaluated by comparing it with gypsum board and lead apron using an X-ray tube. As a result of the experiment, the shielding performance of alumina was lower than that of the gypsum board, and when 50% of alumina was contained, the shielding performance was similar to that of the gypsum board. Iron oxide became similar to the shielding performance of lead apron when it contained about 75%. A shielding material using alumina shows shielding performance similar to that of gypsum, so it is not suitable as a substitute for lead. However, since iron oxide exhibits similar shielding performance to lead, it can be used as an X-ray shielding material to replace lead in the future, so further research is needed.

• Journal of the Korean Ceramic Society
• /
• v.17 no.1
• /
• pp.35-41
• /
• 1980

Alumina extraction from raw Hadong kaolin with sulfuric acid was studied to obtain relatively pure alumina. Factors as acid concentration, heating temperature and conditions of ammonium alum crystal formation from extracted solution are also surveyed and most of iron oxide in kaolin is eliminated in crystallization of ammonium alum. Pure crystal obtained from the extracted solution with ammonium sulfate is relatively free from iron containment in mother liquor. Alumina in ammonium alum crystal is converted to gibbsite form after complete hydrolysis in ammonia gas.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.498-504
• /
• 2012

Oxide layers were prepared by an environmentally friendly plasma electrolytic oxidation (PEO) process on an Al-1050 substrate. The electrolyte for PEO was an alkali-based solution with $Na_2SiO_3$ (8 g/L) and NaOH (3 g/L). The influence of the electrical parameters on the phase composition, microstructure and properties of the oxide layers formed by PEO were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The voltage-time responses were recorded during various PEO processes. The oxides are composed of two layers and are mainly made of ${\alpha}$-alumina, ${\gamma}$-alumina and mullite phases. The proportion of each phase depends on various electrical parameters. It was found that the surface of the oxides produced at a higher current density and Ia/Ic ratio shows a more homogeneous morphology than those produced with the electrical parameters of a lower current density and lower Ia/Ic ratio. Also, the oxide layers formed at a higher current density and higher Ia/Ic ratio show high micro-hardness levels.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.5
• /
• pp.789-792
• /
• 2006

• Korean Journal of Materials Research
• /
• v.12 no.2
• /
• pp.121-128
• /
• 2002

Anodic alumina layer can be used as templates for preparation of nano-structured materials, because porous oxide layer on aluminum shows a uniform pore size and a high pore density. In order to find out possibility for template material to prepare nano wire, the effects of the anodic applied potential, anodic time and the temperature of electrolyte on pore diameter of anodic alumina layer were studied using SEM and AFM. The pore diameter of anodic alumina layer increased with applied anodic potential and electrolytic temperature. Especially, the pore diameter of anodic oxide layers formed in chromic acid can be well replicated by widening process in $H_3$$PO_4$solution.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.6 s.261
• /
• pp.665-670
• /
• 2007

Alpha-phase alumina TGO(Thermally Grown Oxide) forms on the interface between zirconia top coat and bond coat of thermal barrier coating system for superalloys during exposure to high temperature over $1000^{\circ}C$. It is known to provide a good protection against hot corrosion and to cause surface failure such as rumpling and cracking due to difference in thermal expansion coefficient from the substrate metal and the lateral growth. Consequently, mechanical properties of the alumina TGO at the high temperature are the key parameters determining the integrity of TBC system. In this work, by using Fecralloy foils as the alumina forming substrate, creep tests and tensile tests have been performed with various TGO thicknesses$(h=0{\sim}4{\mu}m)$ and yttrium contents(0, 200ppm) at $1200^{\circ}C$. Displacement-time curves and load-displacement curves for each TGO thickness(h=1,2,..) were measured from the creep and tensile tests, respectively, and compared with the curves without TGO thickness(h=0). As the result, the intrinsic tensile and creep properties of TGO itself were determined.

• Journal of the Korean Ceramic Society
• /
• v.31 no.3
• /
• pp.337-345
• /
• 1994

The reaction-sintered alumina and zirconia-alumina ceramics having low firing shrinkage were prepared from the Al/Al2O3 or Al/ZrO2(Ca-PSZ) powder mixtures via the attrition milling. And in this milling process the effect of the characteristics of used powders was investigated. Attrition milling was much more effective in reducing the particle size of ceramic/metal mixed powders than ball milling. Powder mixtures of flake-type Al with coarse alumina was much more effectively comminuted by the attrition milling than the mixtures of globular-type Al with coarse alumina powders. And coarse alumina than fine alumina was much more beneficial in cutting and reducing the ductile Al particles. In the contrary to Al/Al2O3 powder mixtures, Al/ZrO2 powder mixtures was not effectively comminutd. But whether using the alumina ball media or attrition milled with Al2O3 powder rather than Al, the milling efficiency was much more increased.

• Journal of the Korean Magnetics Society
• /
• v.20 no.5
• /
• pp.191-195
• /
• 2010

We have investigated the effect of the removal of an initial oxide layer and the anodization time on the growth of the porous alumina layer. The porous alumina layer was fabricated by two-step anodization process with phosphoric acid. We have observed the changes in the uniformity of the pore structure by varying the removing time of the initial oxide layer after the first anodization with phosphoric acid and chromic acid, and noted that its uniformity improves with the removing time. We have also determined the thickness of the alumina layer after the final anodization process and found that the thickness increases linearly with the anodization time. Under 150 V of anodization voltage with phosphoric acid, the growth rate of the porous alumina layer is determined to be 22.5 nm/min.

• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1401-1413
• /
• 1994

The synthesis of kaolinite mineral from domestic diatomite for silica resource, commercial vailable gibbsite or alumina for alumina resource were made under various hydrothermal treatment, and the sythetic effect of acidic mineralizers, temperature treatment with time duration, particle size of alumina on formation of kaolinite mineral and the plastic properties of synthesized kaolinite were investigated. The various acidic mineralizers which are HCl, HNO3, H2SO4 and Oxalic acid were employed for hydrothermal reaction in the range of 0.01 mol/ι to 2 mol/ι concentration of each mineralizers. It was found that HCl in the level of 1 mol/ι solution produced highly yields of well-crystallized and platy form kaolinite mineral and gave the most effective extraction of iron oxide, compared to that of others, that HNO3 produced highly yield of kaolinite but lower extraction of iron oxide, that H2SO4 produced low yield of kaolinite and formed alunite mineral, and that oxialic acid formed spherical crystalline kaolinite and gave low extraction of iron oxide. Moreover, it showed that kaolinite minerals were well synthesized in a wide range of less than 2 mol/ι acids, but were poorly synthesized at more than 2 mol/ι acids. However, boehmite and kaolinite were coexistently formed in the temperature range of 18$0^{\circ}C$ and 20$0^{\circ}C$ when the calcined diatomite and gibbsite were involved. The well-ordered kaolinite mineral as a platy form was highly synthesized in the temperature range of 220 and 24$0^{\circ}C$, when the same marterials as above were used with treatment of 1 mol/ι HCl solution. The results also revealed that the size of crystalline platy form kaolinite, synthesized from alumina and calcined diatomite with treatment in 1 mol/ιHCl solution at 24$0^{\circ}C$, was much larger than that of gibbsite and calcined diatomite shown previously, and that kaolinite and corundum minerals were coexistently formed under any hydrothermal treatment conditions. The plasticity of synthesized kaolinite from under 2 ${\mu}{\textrm}{m}$ alumina and calcined diatomite was very poor, and that of the synthesized kaolinite from raw diatomite and gibbsite gave higher than that of calcined diatomite and gibbsite.