• Journal of the Korean Operations Research and Management Science Society
• /
• v.37 no.4
• /
• pp.51-65
• /
• 2012

Battery switching EVs are considered to be a promising alternative to overcome long charging time problems in the EV adoption. The purpose of this research is to develop integrated model for battery inventory and battery switching waiting times. Due to complexity of exact analysis, a practical approximation method is developed, which provides close results to exact values. Numerical experiments show that there exist trade-offs between the battery inventory level and the number of switching stations. The proposed model can be applied to evaluate and select the minimum cost alternative in implementing the battery switching stations.

• Journal of Arbitration Studies
• /
• v.32 no.4
• /
• pp.87-101
• /
• 2022

Since Research and Development has been expanded by government, It is very important to evaluate the outcome of Research and Development. Government have levied the penalty of researchers who misused research funding as time goes on. However, there is no protect law for the research before 2021. Government put new committee for the researchers to judge whether their action is legal or illegal based of Innovation Act 2021. Due to the various outcome index of research and development, many firms which is paticipating the research and development have been confused the outcome index. Also, It is difficult for government agencies for management to evaluate the outcome. Even if the committee is trying to solve dispute between researchers and the government agencies, it is not enough to solve it. Therefore, we need to consider Alternative Dispute Resolution(ADR), because the ADR has been developved detail skills for long time.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.3
• /
• pp.337-345
• /
• 2009

The dependence of numerous systems on electronic devices is causing rapidly increasing concern over fault tolerance because of safety issues of safety critical system. As an example, a vehicle with electronics-controlled system such as x-by-wire systems, which are replacing rigid mechanical components with dynamically configurable electronic elements, should be fault￢tolerant because a devastating failure could arise without warning. Fault-tolerant systems have been studied in detail, mainly in the field of aeronautics. As an alternative to solve these problems, this paper presents the fuzzy hybrid redundancy system that can remove most erroneous faults with fuzzy fault detection algorithm. In addition, several numerical simulation results are given where the fuzzy hybrid redundancy outperforms with general voting method.

• Journal of Magnetics
• /
• v.21 no.3
• /
• pp.405-412
• /
• 2016

In general, surface mounted PM synchronous motors (SPMSMs) are mainly adopted as a driving motor for high-speed applications, because they have high efficiency and high power density. However, the SPMSMs have some weak points such as the increase of magnetic reluctance and additional losses as a consequence of using a non-magnetic sleeve. Especially, the magneto-motive force (MMF) in the air-gap of the SPMSMs is weakened due to the magnetically increased resistance. For that reason, a large amount of PM is consumed to meet the required MMF. Nevertheless, it cannot help using the sleeve in order to maintain the mechanical integrity of a rotor assembly in high-speed rotation. Thus, in this paper, a multi-layer interior PM synchronous motor (IPMSM) not using the sleeve is presented and designed as an alternative of a SPMSM. Both motors are evaluated by test results based on a variety of characteristics required for an air blower system of a fuel cell electric vehicle.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.59-61
• /
• 1996

Fuel cell systems offer high efficiencies for energy conservation for transportation application. In addition, they can operate on alcohols and alternative fuels, while producing little or no noxious emissions. The goal of the fuel cell in transportation should be research and commercialization of fuel cell vehicles as economic competitors for internal combustion engine vehicle. The objective of the present study is to analyze feasibility of the fuel cell/battery combination as a power source for a bus.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.39-47
• /
• 2003

UEGI (Unburned Exhaust Gas Ignition) is an alternative method for fast light-off of a catalyst. It ignites the unburned exhaust mixture using two glow plugs installed in the upstream of the close-coupled catalysts. In addition, a hydrocarbon adsorber was applied to the UEGI, for more effective reduction of HC emission. Engine bench tests show that the CCC reaches the light-off temperature laster than the baseline exhaust system and HC and CO emissions are reduced significantly during the cold start. From the vehicle test, it was observed that a few amount of HC emission was reduced even the catalysts were aged. It is expected to develop a solution kit applicable to a new vehicle or used one, to meet the emission regulation

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.112-117
• /
• 2010

This study presents a methodology to evaluate the driving safety of vehicles against localized high wind on the roads over the valleys or along the coasts. Risk level for vehicle accident is derived from the side slip caused by cross wind, and then safety criteria based on reliability for driving stability are defined. The level of safety is classified according to probability of exceeding against wind speed using the concept of extreme value statistics. To attain the safety level of vehicle on bridges, numerical simulations using Computational Fluid Dynamics(CFD) are performed. Based on this result, risk reduction and quality improvement is expected through analysis for each alternative in bridges design, construction and operation & maintenance stage with proposed process

• International Journal of Automotive Technology
• /
• v.7 no.5
• /
• pp.565-570
• /
• 2006

The development of a light-weight vehicle is in great demand for enhancement of fule efficiency and dynamic performance. The vehicle weight can be reduced effectively by using lightweight materials such as aluminum and magnesium. However, if such materials are used in vehicles, there are often instances when different materials such as aluminum and steel need to be joined to each other. The conventional joining method, namely resistance spot welding, cannot be used in joining different materials. Self-piercing rivet(SPR) and adhesive bonding, however, are good alternatives to resistance spot welding. This paper is concerned with the crushing test of double hat-shaped member made by resistance spot welding, SPR and adhesive bonding. Various parameters of crashworthiness are analyzed and evaluated. Based on these results, the applicability of SPR and adhesive bonding are proposed as an alternative to resistance spot welding.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.11
• /
• pp.1180-1188
• /
• 2008

As many systems depend on electronics, concern for fault tolerance is growing rapidly in the safety critical system such as intelligent vehicle. In order to make system fault tolerant, there has been a body of research mainly from aerospace field including predictive hybrid redundancy by Lee. Although the predictive hybrid redundancy has the fault tolerant mechanism to satisfy the fault tolerant requirement of safety crucial system such as x-by-wire system, it suffers form the variability of prediction performance according to the input feature of system. As an alternative to the prediction method of predictive hybrid redundancy for robust fault tolerant, Kalman prediction has attracted some attention because of its well-known and often-used with its structure called Kalman hybrid redundancy. In addition, several numerical simulation results are given where the Kalman hybrid redundancy outperforms with predictive smoothing voter.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.11
• /
• pp.1112-1117
• /
• 2014

Unmanned aerial vehicles (UAVs) are a popular research topic because of a great ripple effect in the future. However, current UAV technologies cannot be applied to manual aerial vehicles without any modification. As an alternative to current UAV technology, humanoid robots are adopted as pilots. If a humanoid robot controls an aerial vehicle autonomously, not only could manual aerial vehicles be utilized as UAVs, but the humanoid robot would also be put into an environment created for humans and conduct some missions suitable for humans. Humanoid robots are also able to handle tools and equipment designed for humans. In order to prove that a humanoid robot can pilot an airplane, an experiment is performed and the results of this experiment are shown in this paper.