• Nuclear Engineering and Technology
• /
• v.55 no.11
• /
• pp.4096-4101
• /
• 2023

Radon is a radioactive gas produced from the uranium-238 series. Radon gas affects public health and is the second cause of lung cancer. The study samples were collected from one area of the city of Jazan, southwest of the Kingdom of Saudi Arabia. The influence of engineering and physical parameters on the emanation coefficient of gas and other gas parameters was studied. Parameters for radon were measured using a CR-39 Solid-State Nuclear Track Detector (SSNTD) through a sealed emission container. The results showed that the emanation coefficient was affected directly by the change in the grain size of the soil. All parameters of measured radon gas have the same behavior as the emanation coefficient. The relationship between particle size and emanation coefficient showed a good correlation. The values of the emanation coefficient were inversely affected by the mass of the sample, and the rest of the parameters showed an inverse behavior. The results showed that increasing the volume of the container increases the accumulation of radon sons on the wall of the container, which increases the emission factor. The rest of the parameters of radon gas showed an inverse behavior with increasing container size. The results concluded that changing the engineering and physical parameters has a significant impact on both the emanation coefficient and all radon parameters. The emanation coefficient affects the values of the radiation dose of an alpha particle.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.3
• /
• pp.292-296
• /
• 2022

(La_0.5Nd_0.2Sr_0.3)MnO₃ specimens were prepared by a solid-state reaction. In all specimens, X-ray diffraction patterns of an orthorhombic structure were shown. The fracture surfaces of (La_0.5Nd_0.2Sr_0.3)MnO₃ specimens showed a transgranular fracture pattern be possibly due to La ions (0.122 nm) as a perovskite A-site dopant substituting for Nd ions (0.115 nm) having a small ionic radius. The full-width at half maximum (FWHM) of the Mn 2p XPS spectra showed a value greater than that [8] of the single valence state, which is believed to be due to the overlapping of Mn²⁺, Mn³⁺, and Mn⁴⁺ ions. The dependence of Mn 2p spectra on the Mn³⁺/Mn⁴⁺ ratio according to sintering time was not observed. Electrical resistivity resulted in the minimum value of 100.7 Ω-cm for the specimen sintered for 9 hours. All specimens show a typical negative temperature coefficient of resistance (NTCR) characteristics. In the 9-hour sintered specimen, TCR, activation energy, and B25/65-value were -1.24%/℃, 0.19 eV, and 2,445 K, respectively.

• Journal of the Korea Concrete Institute
• /
• v.21 no.5
• /
• pp.557-563
• /
• 2009

This study is on the properties of inorganic porous calcium silicate material made from silica powder through the autoclaving curing, the results of this study should be utilized fundamental data for the development of noise reduction porous solid material using siliceous byproduct generated by various manufacture process. For the manufacture of autoclave curing specimen, various calcareous materials used and siliceous materials used silica powder. In this study, properties in density and compressive strength according to the change of W/B and C/S ratio, microscopy for the shape of pore, SEM and XRD for the examination of hydrate after autoclave curing are carried out respectively. The test results shown that the more slurry density decrease, the more W/B increase at the fresh state, this tendency shown similar to in hardened state. Among the specimens of C/S ratio, the compressive strength of C/S ratio of 0.85 gave the highest the compressive strength. In the results of XRD, tobermorite generated by autoclaving curing was created all of specimens regardless of C/S ratio. To ascertain pore structure, we compared with existing porous calcium silicate product(ALC, organic sound absorbing porous material). The results of microscope observation, pore structure of specimen of this study was similar to that of existing inorganic sound absorbing foam concrete. therefore, we could conformed a possibility of sound absorbing porous solid material on the basis of the results.

• Korean Journal of Ecology and Environment
• /
• v.40 no.1
• /
• pp.14-30
• /
• 2007

The purpose of this study was to evaluate trophic conditions of various Korean reservoirs using Trophic State Index (TSI) and predict the reservoir conditions by empirical models. The water quality dataset (2000, 2001) used here were obtained from the Ministry of Environment, Korea. The water quality, based on multi-parameters of dissolved oxygen (DO), biological oxygen demand (BOD), chemical oxygen demand (COD), total phosphorus (TP), total nitrogen (TN), suspended solid (SS), Secchi depth (SD), chlorophyll-${\alpha}$ (CHL), and conductivity largely varied depending on the sampling watersheds and seasons. In general, trophic conditions declined along the longitudinal axis of headwater-to-the dam and the largest seasonal variations occurred during the summer monsoon of July-August. Major inputs of TP occurred during the monsoon (r=0.656, p=0.002) and this pattern was similar to solid dynamics of SS (r=0.678, p<0.001). Trophic parameters including CHL, TP, SD, and TN were employed to evaluate how the water systems varies with season. Trophic State Index (TSI, Carlson, 1977), based on TSI (CHL), TSI (TP), and TSI (SD), ranged from mesotrophic to eutrophic. However, the trophic state, based on TSI (TN), indicated eutrophic-hypereutrophic conditions in the entire reservoirs, regardless of the seasons, indicating a N-rich system. Overall, nutrient data showed that phosphorus was a primary factor regulating the trophic state. The relationships between CHL (eutrophication index) vs. trophic parameters (TN, TP, and SD) were analysed to develop empirical models which can predict the trophic status. Regression analyses of log-transformed seasonal CHL against TP showed that the value of $R^2$ was 0.31 (p=0.017) in the premonsoon but was 0.69 (p<0.001) during the postmonsoon, indicating a greater algal response to the phosphorus during the postmonsoon. In contrast, SD had reverse relation with TP, CHL during all season. TN had weak relations with CHL during all seasons. Overall, data suggest that TP seems to be a good predictor for algal biomass, estimated by CHL, as shown in the empirical models.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.5
• /
• pp.218-224
• /
• 2011

LAS ($Li_2O-Al_2O_3-SiO_2$) ceramics were sintered by a solid-state reaction. $CaCO_3$ and $ZrO_2$ were added to the ${\beta}$-spodumene ($Li_2O-Al_2O_3-4SiO_2$) composition of the LAS system for enhancement of sintering behavior and mechanical strength, respectively. We have investigated the sintering characteristics, microstructures, mechanical properties and thermal expansion characteristics according to the change of the amount of additive and sintering temperature of the ${\beta}$-spodumene. At 0.1 mol% $CaCO_3$, the densification of ${\beta}$-spodumene was significantly improved. At 0.04 mol% $ZrO_2$, the strength of ${\beta}$-spodumene was also improved. For all the selected all compositions, the thermal expansion coefficient was measured by a dilatometer, which revealed 1.2 to $1.7{\times}10^6/^{\circ}C$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.17 no.1
• /
• pp.117-124
• /
• 2006

By calcining at $750^{\circ}C$ for 30 h in $O_2$ stream after milling, $LiNi_{1-y}In_yO_2$(y = 0.005, 0.01, 0.025, 0.05, and 0.1) were synthesized and their electrochemical properties were investigated. All the samples had the $R{\bar{3}}m$ structure. In addition, they contained $LiInO_2$ phase and the intensities of the peaks for the $LiInO_2$ phase increased as the value of y increased. The sample with y = 0.01 had the largest first discharge capacity (140.2 mAh/g), but the sample with y = 0.005 had a better cycling performance. The samples with y $\geq$ 0.025 had a bad cycling performance irrespective of the first discharge capacity. The sample with y = 0.005 had the largest value of $I_{003}/I_{104}$ and the smallest value of R-factor. Among all the samples, $LiNi0_{0.995}In_{0.005}O_2$ had the best electrochemical properties. This sample had a smaller first discharge capacity than $LiNiO_2$, but it showed a better cycling performance than $LiNiO_2$.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.2
• /
• pp.260-267
• /
• 2020

In this study, supercapacitor based on the all solid state electrolyte with PVA(polyvinyl alcohol), ionic liquid as a BMIMBF4(1-buthyl-3-methylimidazolium tetrafluoroborate) and activated carbon/Ni-MOF composite was fabricated and characterized its electrochemical properties with function of MOF. In order to analysis and comparison that electrochemical performances [including cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS) and galvanostatic charge/discharge test] of prepared supercapacitor based on activated carbon/Ni-MOF composite and all solid state electrolyte. As a result, specific capacitance of the supercapacitor without Ni-MOF was 380 F/g which value decreased to 340 F/g after adding Ni-MOF to activated carbon as a electrode material. This result exhibited that decreased electrochemical property of the supercapacitor effected on physical hinderance in the electrode. In further, it needs to optimization of the Ni-MOF amount (wt%) in the electrode composite to maximize its electrochemical performances.

• Journal of the Korean Ceramic Society
• /
• v.42 no.5 s.276
• /
• pp.352-358
• /
• 2005

By calcining at $750^{\circ}C$ for 30 h in $O_2$ stream after milling, $LiNi_{1-y}M_yO_2(M=Zn^{2+},\;Al^{3+}$, and $Ti^{4+}$, y = 0.005, 0.01, 0.025, 0.05, and 0.1) were synthesized and their electrochemical properties were investigated. All the samples had R3m structure. $LiNi_{1-y}Zn_yO_2$ (y = 0.025, 0.05, and 0.1) contained ZnO anuor $Li_2ZnO_2$ as impurities. Among the samples substituted with the same element, the samples with relatively large value of $I_{003}/I_{104}$ and the smallest R-factor had the largest first discharge capacity and good cycling performance. $LiNi_{0.975}A1_{0.025}O_2$ had the largest first discharge capacity (172.5 mAh/g) and good cycling performance (about $89.4\%$ of the first discharge capacity at the 20th cycle). This sample had the largest value of $I_{003}/I_{104}$ and the smallest R-factor among all the samples. In addition, the particles of this sample were finer and their size was more homogeneous than the other samples. $LiNi_{0.95}A1_{0.05}O_2$ had relatively large first discharge capacity 150.4 mAh/g and good cycling performance.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.2
• /
• pp.47-54
• /
• 2020

To develop the bright-vivid red- and yellow-inorganic fluorescent pigments with high luminescence properties, A₃V₅O₁₄ (A = K and Rb) and Cs₂V₄O₁₁ inorganic pigments were synthesized by a water assisted solid state reaction (WASSR) method and a conventional solid state reaction method. Although impurity peaks corresponding to the AVO₃ and AV₃O₈ (A = K, Rb, and Cs) were observed in all samples prepared, the trigonal structure A₃V₅O₁₄ (A = K and Rb) and orthorhombic structure Cs₂V₄O₁₁ were successfully obtained as a main phase. These inorganic pigments showed the broad absorption band (under 550 nm) originated from CT transitions of VO₄ polyhedron, and the strong broad red- and green-emission bands due to ³T₂ → ¹A₁ and ³T₁ → ¹A₁ transitions of the [VO₄]^3- group. The A₃V₅O₁₄ (A = K and Rb) and Cs₂V₄O₁₁ pigments showed a bright-vivid red- and yellow-body color, where the a* values of the A₃V₅O₁₄ (A = K and Rb) were +35.5 and +45.9, respectively, and b* value of Cs₂V₄O₁₁ pigments was +50.3. The L* values of the A₃V₅O₁₄ (A = K and Rb) and Cs₂V₄O₁₁ inorganic pigments were over +45. These results indicate that the A₃V₅O₁₄ (A = K and Rb) and Cs₂V₄O₁₁ inorganic pigments could be an attractive candidate as a bright-vivid red- and yellow inorganic pigments.

• Journal of the Mineralogical Society of Korea
• /
• v.31 no.4
• /
• pp.295-306
• /
• 2018

Despite the utility of solid-state NMR, NMR studies of iron-bearing silicate glasses remain a challenge because the variations in the peak position and width with increasing iron content reflect both paramagnetic effect and iron-induced structural changes. Therefore, it is essential to elucidate the effect of temperature on the NMR signal for iron-bearing silicate glasses. Here, we report the $^{29}Si$ and $^{27}Al$ MAS NMR spectra for $(Mg_{0.95}Fe_{0.05})SiO_3$ and $Fe_2O_3$-bearing $CaAl_2Si_2O_8$ (anorthite) glasses with varying spinning speed to interpret the NMR spectra for iron-bearing silicate glasses. The increase in the spinning speed results in an increase in the sample temperature. The current NMR results allow us to understand the origins of the changes in NMR signal with increasing iron content and to provide information on the dipolar interaction between nuclear spins. The $^{29}Si$ NMR spectra for $(Mg_{0.95}Fe_{0.05})SiO_3$ glass and $^{27}Al$ NMR spectra for $Fe_2O_3$-bearing $CaAl_2Si_2O_8$ glasses show that the peak shape and position of iron-bearing glasses do not change with increasing spinning speed up to 30 kHz. These results suggest that the NMR signal in the Fe-bearing glasses may stem from the 'survived nuclear spins' beyond the cutoff radius from the Fe, not from the paramagnetic shift. Based on the current results, the observed apparent shifts toward lower frequency of Al peak for $Fe_2O_3$-bearing $CaAl_2Si_2O_8$ glasses with increasing $Fe_2O_3$ at all spinning speed (15 kHz to 30 kHz) indicate the increase in the fraction of ${Q^4}_{Al}$(nSi) with lower n (i.e., 1 or 2) with increasing $Fe_2O_3$ and the spatial proximity between Fe and ${Q^4}_{Al}$(nSi) with higher n (i.e., 3 or 4). The present results show that changes in the NMR signal for iron-bearing silicate glasses reflect the actual iron-induced structural changes. Thus, it is clear that the applications of solid-state NMR for iron-bearing silicate glasses hold strong promise for unraveling the atomic structure of natural silicate glasses.