• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.1
• /
• pp.50-57
• /
• 2015

Portland cement production is under critical review due to high amount of $CO_2$ gas released to the atmosphere. Attempts to increase the utilization of a by-products such as fly ash and ground granulated blast-furnace slag to partially replace the cement in concrete are gathering momentum. Many researchs on alkali-activated concrete that does not need the presence of cement as a binder have been carried out recently. Instead, the sources of material such as fly ash, that are rich in Silicon(Si) and Aluminium(Al), are activated by alkaline liquids to produce the binder. Hence concrete with no cement is effect reduction of $CO_2$ gas. In this study, we investigated the influence of the fluidity, air content and compressive strength of mortar on alkaline activator in order to develop cementless fly ash and ground granulated blast-furnace slag based alkali-activated mortar with superplasticizer. In view of the results, we found out that Pn of fluidity and compressive strength is the best in four type of superplasticizer, and PNS of powder type of fluidity is better than that of liquid type in the case of AA.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.18 no.2
• /
• pp.117-125
• /
• 2014

This paper examines the fundamental properties of alkali-activated slag cement (AASC) activated by sodium hydroxide (NaOH). The water to binder (W/B) ratio was 0.4 and 0.5. And concentration of activator were 2M and 4M. Five mix design of each W/B ratios was considered. The N0 mixture was KS L 5109 method and N1~N4 were varied in different mixing time, mix step and entering points of fine aggregate. Test results clearly showed that the flow value, strength and drying shrinkage development of AASC were significantly dependent on the entering point of fine aggregate. The flow value tended to decreases with delaying entering point of fine aggregate. The compressive strength and flexural strength increases with delaying entering point. Moreover, the XRD analysis confirmed that there were sustain these results. The drying shrinkage increases with delaying entering point of fine aggregate. Futhermore, a modified mixing method incorporating all hereby experimentally derived parameters, is proposed to improvement the physical properties of AASC.

• Journal of the Korean Ceramic Society
• /
• v.40 no.10
• /
• pp.1005-1014
• /
• 2003

This paper examines the hydration and physical properties of alkali-blast furnace slag cement activated by Na$_2$SiO$_3$, Na$_2$CO$_3$, NaOH, Na$_2$SO$_4$. Four levels of Na$_2$O content in mixtures, 1, 3, 5, and 7 wt%, were investigated, and a W/S ratio 0.5 was used to prepare paste and mortar specimens. Compressive strength measurement of mortars was carried out adding alkali activated slag 30 wt% to OPC. The main hydration products with alkali activator kinds were C-S-H,C$_4$AH$\_$13/, AFt and Al(OH)$_3$ etc. For using Na$_2$CO$_3$ activated slag, hydration ratio of slag was higher than that of different activators, and Na$_2$SO$_4$ activated slag mortar appeared the highest compressive strength values at 28 days with activator content of 5 and 7 wt%.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.77-78
• /
• 2020

An alkaline activator was synthesized by dissolving waste glass powder (WGP) in NaOH-4M solution to explore its effects on the Class-C fly ash (FA) and ground granulated blast furnace slag (GGBS) based alkali-activated material (AAM). The compressive strength and porosity were measured, and (SEM-EDX) were used to study the hydration mechanism and microstructure. Results indicated that the composition of alkali solutions was significant in enhancing the properties of the obtained AAM. As the amount of dissolved WGP increased in alkaline solution, the silicon concentration increased, causing the accelerated reactivity of FA/GGBS to develop Ca-based hydrate gel as the main reaction product in the system, thereby increasing the strength. Further increase in WGP dissolution led to strength loss, which were believed to be due to the excessive water demand of FA/GGBS composites to achieve optimum mixing consistency. Increasing the GGBS proportion in a composite also appeared to improve the strength which contributed to develop C-S-H-type hydration.

• Advances in materials Research
• /
• v.4 no.3
• /
• pp.179-192
• /
• 2015

The study presents a preliminary investigation on the applicability of Shirasu (a pyroclastic flow deposit characterized by high percentage of volcanic glass) in geopolymer. Comparative study on compressive strength and internal pore structure has been done between geopolymers with alkali activated Shirasu and fly ash as aluminosilicates. Mortar mix proportions are selected based on variations in ratio of alkaline activators to aluminosilicate and also on silica to alkali hydroxide ratio. From the experimental study, Shirasu geopolymer exhibited fairly good compressive strength. Mix proportion based on silica to alkali hydroxide ratio is observed to have profound effect on strength development.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.103-106
• /
• 2008

Because the physical·chemical properties of bottom ash are inferior, most bottom ash is disused. But the use of bottom ash helps in reducing environmental pollution and solving some bottom ash waste problems. So, we have been investigating about the optimum mixture, hardening mechanism, curing condition and environmental safety of a paste composed of a bottom ash and alkali. optimal mixing proportion of bottom ash solid was cement 5%, water 30%, NaOH 10%. After curing during 28days, bottom ash solid can be achieved compressive strength 15.13MPa. As a result, Compressive strength tests of alkali-activated bottom ash have potential as a replacement of coarse aggregate.

• Journal of the Korean Society of Safety
• /
• v.13 no.1
• /
• pp.92-97
• /
• 1998

Malodorous gases give discomfort and harm to laborers and residential neighborhoods and therefore, the removing odor materials emitted from plants and industrial facilities is important subject. The main ingredients of alkali odor are $NH_3$ and $CE_3SH$. The adsorption characteristics of odors were studied using four different activated carbon fibers(ACF) and active carbon(AC). Alkali odor was removed by using ACF impregnated with $H_3PO_4$ and $H_2SO_4$ and treated with $HNO_3$ and NaOH. The experimental result showed that ACF has a higher removal efficiency than AC. The adsorption capacity was increased with the impregnation and surface treatment, and $H_2SO_4$ was the best impregnant for the removal of alkali odor.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.11a
• /
• pp.627-630
• /
• 2005

This paper examines degradation properties of alkali-activated alumino-silicate composite body by NAS solution exposed to high temperature. Activators include sodium hydroxides and sodium silicate solution. In the result of experiment, flexural and compressive strength of AAS base mortar exposed to high temperature ($400\~600^{\circ}C$) was higher than alumina cement base mortar. Particularly, In case of compressive strength, alumina cement base mortar was decreased by about $60\~70\%$. While, AAS base mortar exposed to high temperature ($400\~600^{\circ}C$) was higher than that curing by room temperature. The above results showed that AAS base inorganic binder has a good mechanical properties exposed to high temperature($400\~600$).

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.313-317
• /
• 2003

The study is the results of accelerated tests and the specimens, mortars, are submerged in a 5% sulfuric acid solution. The deterioration of specimens is followed up by investigating the change in weight and compressive strength of the specimens and techniques such as XRD and XRF are used to examine the chemical changes. Sulfuric acid is a very aggressive acid that reacts with the free lime [$Ca(OH)_2$] in the concrete forming gypsum($CaSO_{4}.2H_{2}O$). This reaction is associated with an increase in volume of the concrete, and the corroded surface becomes soft and white. The results showed that the OPC mortar caused an decrease in weight above 18% and strength loss about 57%. On the other hand, AASC(alkali-activated slag composites) did not cause any decrease in weight and in the case of strength caused an decrease below 10%. In addition, this mechanical results was verified to XRD and XRF.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.361-362
• /
• 2010

Six alkali-activated(AA) concrete mixes were tested to ascertain the effect of unit binder content on the slump and compressive strength of concrete. Test results showed that the compressive strength of AA-concrete increased with the increase of the unit binder content, while the increasing rate was lower that recorded in ordinary portland cement concrete.