• Resources Recycling
• /
• v.22 no.2
• /
• pp.22-28
• /
• 2013

In the present study, the possibility of recovering and recycling the silicon carbide(SiC) from a silicon sludge by removing Fe and Si impurities was investigated. Si and SiC were separated from the silicon sludge using centrifugation. The separated SiC concentrate consisted of Fe, Si and SiC, in which Fe and Si were removed to recover the pure SiC. Leaching with acid/alkali solution was compared with the vapor-phase chlorination. The Fe concentration removed in the SiC was 49 ppm, and it was separated by leaching with 1 M HCl solution at $80^{\circ}C$ for 1 h. The Si concentration removed in the SiC was 860 ppm, and it was separated by leaching with 1M NaOH solution at $50^{\circ}C$ for 1 h. The SiC concentrate was chlorinated in a tubular reactor, 2.4 cm in diameter and 32 cm in length. The boat filled with SiC concentrate was located at the midpoint of the alumina tube, then, the chlorine and nitrogen gas mixture was introduced. The Fe and Si concentration removed in the SiC were 48 ppm and 405 ppm, respectively, at $500^{\circ}C$ reactor temperature, 4 h reaction time, 300 cc/min gas flow rate, and 10% $Cl_2$ gas mole fraction.

• Korean Journal of Materials Research
• /
• v.11 no.6
• /
• pp.465-471
• /
• 2001

The effect of sintering condition on the mechanical properties and leachability of polydispersed ceramic core body made by gel-casting process in aqueous medium have been investigated. The polydispersed ceramic slip that has low viscosity($\leq$1000cP, at 1000cP (at $50sec^{-1}$ ) and high solid loading(50vo1%) was obtained. The green bodies were fabricated through casting and gelation at room temperature followed by drying at $25^{\circ}C$for 48hrs under relative humidity of 80%. Crack-free green body was successfully fabricated through the above process. The strength at room temperature, apparent bulk density, and shrinkage of the ceramic core body increased propotionally with increasing sintering temperature(1100~150$0^{\circ}C$). However, porosity of the ceramic core body showed relatively low vague. Leaching rate of sintered core body increased with increasing porosity of the sintered body, and was significantly dependent upon the concentration of alkali caustic solution at the same leaching temperature.

• Geomechanics and Engineering
• /
• v.16 no.1
• /
• pp.105-112
• /
• 2018

This paper presents results of a compressive investigation conducted on weathered soil stabilized with ground bottom ash (GBA) and red mud (RM). The effects of water/binder ratio, RM/GBA ratio, chemical activator (NaOH and $Na_2SiO_3$) and curing time on unconfined compressive strength of stabilized soils were examined. The results show that the water/binder ratio of 1.2 is optimum ratio at which the stabilized soils have the maximum compressive strength. For 28 days of curing, the compressive strength of soils stabilized with alkali-activated GBA and RM varies between 1.5 MPa and 4.1 MPa. The addition of GBA, RM and chemical activators enhanced strength development and the rate of strength improvement was more significant at the later age than at the early age. The potential environmental impacts of stabilized soils were also assessed. The chemical property changes of leachate from stabilized soils were analyzed in terms of pH and concentrations of hazardous elements. The observation revealed that the soil mixture with ground bottom ash and red mud proved environmentally safe.

• Resources Recycling
• /
• v.27 no.6
• /
• pp.23-29
• /
• 2018

Recently rapid economic growth and technological development have led to an increase in the generation of waste electrical and electronic equipment (WEEE). As the amount of electric and electronic waste generated increases, the importance of processing waste printed circuit boards (PCB) is also increasing. Various studies have been conducted to recycle various valuable metals contained in a waste PCB in an environmentally friendly and economical manner. To get anode slime containing Ag and Au, Anode copper prepared from PCB scraps was used by means of electro-refining. Ag and Au recovery was conducted by leaching, direct reduction, and ion exchange method. In the case of silver, the anode slime was leached at 3 M $HNO_3$, 100 g/L, $70^{\circ}C$, and Ag was recovered by precipitation, alkali dissolution, and reduction method. In the case of gold, the nitrate leaching residues of the anode slime was leached at 25% aqua regia, 200 g/L, $70^{\circ}C$, and Au was recovered by pH adjustment, ion exchange resin adsorption, desorption and reduction method. The purity of the obtained Au and Ag were confirmed to be 99.99%.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.5
• /
• pp.340-349
• /
• 2013

The present paper investigates the availability of seawater as the absorbents to capture carbon dioxide ($CO_2$) emitted from the coal fired power plant (CFPP). For the purpose of the study, readily obtainable alkali materials in CFPP such as coal fly ash (FA), NaOH and $Ca(OH)_2$ are added to seawater to prepare the absorbents and their $CO_2$ capture performances are discussed. FA can be effectively used the additives to increase $CO_2$ capture capacity of seawater to a some extent. This is ascribed that some alkali components in FA are leached into seawater and they contribute to $CO_2$ capture in the solution. However, their leaching amount and rate are restricted by the various ions in seawater. The performance of NaOH added seawater is even lower than that of NaOH added water because $OH^-$ is substantially consumed on $Ma(OH)_2$ production prior to carbonation. $CO_2$ absorption capacity of $Ca(OH)_2$ added seawater is slightly larger than that of $Ca(OH)_2$ added water. This is because that $Ca^{2+}$ which originally present in raw seawater can participate in carbonation reaction.

• Particle and aerosol research
• /
• v.12 no.2
• /
• pp.43-50
• /
• 2016

The influence of basalt fibres on the compressive strength of the geopolymer type binders has been studied. For the experiments 2 types of the basalt fibres were used, namely chopped and spooled fibres. Both types of basalt fibres were 7-10 micron thick in diameter and cut into pieces of 6 mm length. The fibres were mixed with 1% weight to the fly ash powder, followed by the addition of the activator solution (8M NaOH). The pastes obtained were cured at $70^{\circ}C$ for 20 h revealing compact bodies. Compressive strength was measured after 7 days and microstructure observation performed with SEM. The cube bodies ($2{\times}2{\times}2cm$) reveal compressive strength of 47.25(4.03) MPa, while it decreased to 34.0(9.05) MPa in spooled basalt fibres and to 17.33(5.86) MPa in the chopped basalt fibres containing binder, i.e 76% and 36% of the strength without fibres, respectively. The much weaker compressive strength of the chopped fibres containing binder is related to the absence of significant adhesion between the geopolymer binder and the basalt fibres, forming voids instead. Alkali leaching effect of basalt fibres could probably explain the drop in the compressive strength with spooled and chopped fibres, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.1
• /
• pp.179-186
• /
• 1998

We have been investigated the effects of the initial pH of the aquous solution, reaction temperature and time for the flaking of the soda-lime glass container. Flaking of glass occuurred in the cases of the $121^{\circ}C$, above pH 11 of solution with no $Mg^{2+}$ ions in solution. The pH of the solution approached to pH 10 under the conditions of below pH 9 of start solution. The flaking mechanism of the glass seem to be composed of formation of leached layer of $Ca^{2+}$ and $Na^{2+}$ ion and separation of these layers during the cooling by the difference of thermal expansion between leached layer and glass surface. The leaching of alkali ions in glass depends on the pH condition of the start solution and the temperature. In the case of $Mg^{2+}$ ions are added, $Mg^{2+}$ ions accelerate the flaking of the sodalime glasses and forms the magnesium silicate compound which result in the decrease of the pH of the solution.

• Applied Chemistry for Engineering
• /
• v.17 no.4
• /
• pp.391-396
• /
• 2006

When radioactive wastewater was solidified treatment by cement, the drying rate of cement and the volume reduction ratio was decreased because of boric acid component in the wastewater. In order to supplement the demerit, effects of paraffin wax investigated in this study. Paraffin wax has a hydrophobic properties and a low affinity with inorganic materials. When the radioactive wastewater was tested by a small of wax, the compressive strength of solidified waste are decreased Therefore boric acid in radioactive wastewater are first treated by alkali salt and coated by the stearic acid. During the solidification step, The amount of paraffin wax addition get the result that the compressive strength of solidification with cement was the same as that with paraffin wax. The leaching properties of radioactive waste solidified was the same CFL (cumulative fraction leached), PR (penetration rate), effective diffusivity if paraffin wax content in solidified waste was 20% or 25%.

• Journal of the Mineralogical Society of Korea
• /
• v.5 no.2
• /
• pp.93-101
• /
• 1992

Several "Napseok" mines are distribute in the Miryang area where the volcanic rocks are hydrothermally altered. The "Napseok" are pyrophyllite and dickite, with a small amount of silicates such as quartz, illite, tosudite and dumortierite. Other associated minerals are oxides, hydroxides, sulfides, sulfates and phosphates. Pyrophyllite which occurs as 2M polytype exhibits that the basal spacing increases due to dehydroxylation at 750${\circ}C$. Halloysite shows tubular forms. Wavellite is precipitated in fissures during the latest stage of the hydrothermal alteration process. Five mineral zones, that is pyrophyllite-deckite, illite, halloysite, silica, and albite-chlorite zones, are recognized with decreasing alteration degree. Clay minerals were formed by leaching of Si and alkali ions fron the country rocks, considering mineral assemblages, pyrophyllite polytype and thermodynamical data reported in the literature, temperatures of formation of main clay deposits are assumed to be 270 to 350${\circ}C$.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.679-684
• /
• 1997

The major constituents in spent FCC catalysts are Si, Al, Fe, Ti, alkali metals and some others. The spent catalyst is also composed small amounts of rare metals such as Ce, Nd, Ni and V. The selective adsorption and concentration of Ce and Nd from the leaching solution of spent FCC catalysts with sulfuric acid($0.25mol/dm^3$) were carried out by the column method with a chelate resin having a functional group of aminophosphoric acid type. Ce and Nd were separated from eluate liquor containing Al, Nd and V by the precipitation process with oxalic acid. Vanadium is purified from chloride ion coexistance by solvent extraction, employing tri-n-octyl phosphine oxide as extractant with Al in the raffinate solution. Rare metals with the purity of 99 percent were obtained from the spent FCC catalyst.