• Korean Journal of Materials Research
• /
• v.10 no.8
• /
• pp.569-574
• /
• 2000

To improve the ductility of $Al_3Hf$ and $Al_3Ta$ intermetallic compounds, which are the potential temperature structural materials, the mechanical alloying behaviour and the effect of ternary additions on the $Ll_2$ phase formation were investigated. During the mechanical alloying by the SPEX mill, the $Ll_2$ $Al_3Hf$ intermetallic compound was formed after 6 hours of milling in AL-25%Hf system. In AL-25%Ta system, however, only the $D0_{22}$ $Al_3Ta$ intermetallic compound was formed until 30 hours of milling and the $Ll_2$ phase was not observed. In AL-12.5%M-25%Ta(M=Cu, Zn, Mn, Fe, Ni) systems, the additions of Cu and Zn had no effect on the $D0_{22}$ structure of the binary $Al_3Hf$ and the additions of Mn, Fe and Ni produced the amorphous phase. Therefore it was considered that these ternary additions could not overcome the energy difference between $Ll_2$ and $D0_{22}$ structures in the $Al_3Hf$ intermetallic compound. In AL-12.5%M-25%Hf(M=Cu, Zn, Mn, Fe, Ni)systems, the additions of Cu and Zn did not affect the $Ll_2$ structure of the binary $Al_3Hf$ but the additions of oMn, Fe and Ni produced the amorphous phase as they did in AL-12.5%M-25%Ta systems. Therefore, it was considered that the Ni, Mn and Fe additions promote the formation of amorphous phase in $Al_3X$ intermetallic compounds.

• Journal of the Korean Ceramic Society
• /
• v.38 no.10
• /
• pp.936-941
• /
• 2001

The influence of the ${Al_2}{O_3}$ particle size on flaw tolerance of the $ZrO_2/{Al_2}{O_3}$ composites prepared by mixing 5.31 mol% ${Y_2}{O_3}$-4.45 mol% ${Nb_2}{O_5}$-90.31 mol% $ZrO_2$ and ${Al_2}{O_3}$ was investigated. The composites exhibited rising R-curve behavior and plateau fracture toughness of 7.9 and $8.8MPam^{1/2}$ for the additions of 20 vol% of 0.2 and $2.8{\mu}m$ ${Al_2}{O_3}$ particles, respectively. The difference in the fracture toughness resistance was attributed mainly to the grain size of tetragonal $ZrO_2$ phase in the composites, which scaled with the ${Al_2}{O_3}$ particle size.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.14 no.1
• /
• pp.5-14
• /
• 1977

"Electrical Properties of Barium Titanates with Addition Sb2O3." PTC BaTiO3 in low resistance at room temperature was prepatred. Al2O3, SiO2 and TiO2 were doped with a view to improving reproduction. Sb2O3 was doped as impurity in order to control of resistivity of the specimens. The relations between the amount of Sb3O3 and electrical properties wereinvestigated. Of the compositions studied, additions of 3.75mole% Al2O3, 1.25mole% SiO2, 2.25mole% TiO2 and 0.16~0.25wt% Sb2O3 to BaTiC3 was low resistivity in 14-300 ohm-cm.00 ohm-cm.

• Korean Journal of Materials Research
• /
• v.5 no.2
• /
• pp.157-168
• /
• 1995

The effects of Mo additions on the microstructure and the room temperature deformation behavior of polysynthetically twinned (PST) crystals of TiAl were studied in order to get a basic conception for alloying additions on the two-phase TiAl compounds with the lamellar structure. It was found that the Mo additions in TiAl PST crystals increase both the yield stress and tensile elongation to fracture but the increase in yield stress deppend on the angle $\Phi$at which the lamellar boundaries lie from the loading axis. The large difference in yield stress between specimens deformed parallel($\Phi = 0^\circ$)or perpendicular($\Phi = 90^\circ$) to the loading axis and those deformed in intermediate orientations could be plained by the difference in Mo content between the TiAl and the $$Ti_{3}Al$ phases. It was also found that the Mo-doped specimens with intermediate orientation fail by cracking zigzag across to the lamellar boundaris, which is the same fracture mode as that of binary specimens with intermediate orientations tested in vacuum This suggests that Mo atoms are thought to play a role to reduce the environmental embrittlement of binary PST crystals, resulting in increasing the tensile ductility.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1134-1136
• /
• 1993

The mean grain size of sample decreases with increasing the addition of $Al_2O_3$ in the basic composition of YIG. It is mean that the addition of $Al_2O_3$ is helpless the development of magnetic properties in YIG garnet, considering the relation of ${\mu}{\propto}D^{1/3}$. To increase addition of $Al_2O_3$ decreased the area of hysterisis loop. It is known that the addition of $Al_2O_3$ is help the development of magnetic properties in YIG garnet, considering the relation of loss component factor and the area of hysterisis loop. As a results, sample with the addition of $Al_2O_3$ 0.5 mol % among the fabricated samples is must effective in the magnetic properties of YIG Garnet.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.397-404
• /
• 2009

Effects of ceramic filler types and dose on the low temperature sintering and dielectric properties of ceramic/$CaO-Al_2O_3-SiO_2$ (CAS) glass composites were investigated. All of the specimens were sintered at $850{\sim}900^{\circ}C$ for 2 h, which conditions are required by the low-temperature co-firing ceramic (LTCC) technology. Ceramic fillers of $CaCO_3$, $Al_2O_3$, $CaCO_3-Al_2O_3$ mixture, and $CaCO_3-Al_2O_3$ compound ($CaAl_2O_4$), respectively, were used. The addition of $Al_2O_3$ yielded the crystalline phase of alumina, which was associated with the inhibition of sintering, while, $CaCO_3$ resulted in no apparent crystalline phase but the swelling was significant. The additions of $CaCO_3-Al_2O_3$ mixture and $CaAl_2O_4$, respectively, yielded the crystalline phases of alumina and anorthite, and the sintering properties of both composites increased with the increase of filler addition and the sintering temperature. In addition, the $CaAl_2O_4$/CAS glass composite, sintered at $900^{\circ}C$, demonstrated good microwave dielectric properties. In overall, all the investigated fillers of 10 wt% addition, except $CaCO_3$, yielded reasonable sintering (relative density, over 93 %) and low dielectric constant (less than 5.5), demonstrating the feasibility of the investigated composites for the application of the LTCC substrate materials.

• Korean Journal of Materials Research
• /
• v.10 no.5
• /
• pp.321-327
• /
• 2000

Two kinds of $Al_2O_3/TZP$ composites were prepared using the liquid infiltration of 3Y-TZP and 12Ce-TZP precursors into hte sintered porous $Al_2O_3$. Small TZP additions(~11.0wt%) had increased the strength(19~59%) and fracture toughness(14~157%) of the sintered Al2O3 material($1600^{\circ}C$, 2h). The addition of 3Y-TZP was effective on case of the strength. By the way, in case of the fracture toughness that of 12Ce-TZP was effective. Infiltrated TZP was concentrated on the surface where its grain growth was enhanced and $Al_2O_3$ grain growth was effectively inhibit-ed, when compared to the inner region of the composite. The indentation crack was propagated through both intergranular modes and transgranular and the proportion if intergranular fracture was the larger in $Al_2O_3/12Ce-TZP$.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.1
• /
• pp.3-9
• /
• 2000

Arc-melted alloys of TiAl-(o.25, 0.5, 1.0at%) Si were isothermally oxidized at 800, 900 and $1000^{\circ}C$ in air for 60hr. It was found that the oxidation resistance of the prepared TiAl-Si alloys was much better than that of pure TiAl, being progressively increasing with an increase in the Si content. This was attributed to the formation of $SiO_2$in addition to ($TiO_2$+$Al_2$$O_3$) oxides which formed in TiAl alloys with and without silicon additions. However, the silica formation within the oxide layer unfortunately accelerated the oxide scale spallations. During oxidation, all the elements in the base alloy diffused outward, whereas oxygen from the atmosphere diffused inward. The oxides were primarily composed of an outer thick $TiO_2$layer, an intermediate diffuse $Al_2$$O_3$layer and an inner $TiO_2$layer. A small amount of $SiO_2$was present all over the oxide scale and some voids were found around the intermediate layer.

• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.787-794
• /
• 1995

To improvement the magnetic and frequency properties of YIG(Yttrium-Iron Garnet) in microwave region, it is investigated that the effect of $Al^{3+}$ ions on magnetic and frequency characteristics of YIG, using samples of basic YIG composition( $Y_{3}$F $e_{5}$ $O_{l2}$) added with A1$_{2}$ $O_{3}$ from 0 to 2.5 [mol%]. The measurment is conducted mainly for the structural properties and magnetical properties. The structural properties is measured using SEM(Scanning Electro Microscope), EDX(Energy-dispersive X-ray spectrometer) and XRD(X-ray diffraction equipment). The magnetical properties is measured with B-H curve tracer and impedance analyzer. As a result, it is confin-ned that the effect of eddy current loss is minimized while maintaining high saturation flux density of YIG, when YIG is added with 0.5 [mol%] of A1$_{2}$ $O_{3}$.>.>.

• Journal of the Korean Ceramic Society
• /
• v.28 no.8
• /
• pp.625-625
• /
• 1991

The specimens for the corrosion test were made by hot-pressing of SiC power with 2 wt% Nl2O3 and 10wt% Al2O3 additions at 2000℃ and 2050℃. The specimens were corroded in 37 mole% NaCl and 63 mole% Na2SO4 salt mixture at 1000℃ up to 60 min. SiO2 layer was formed on SiC and then this oxide layer was dissolved by Na2O ion in the salt mixture. The rate of corrosion of the specimen containing 10 wt% Al2O3 was slower than that of the specimen containing 2 wt% Al2O3. This is due to the presence of continuous grain boundary phase in the specimen containing 10 wt% Al2O3. The oxidation of SiC produced gas bubbles at the SiC-SiO2 interface. The rate of corrosion follows a linear rate law up to 50 min. and then was accelerated. This acceleration is due to the disruption oxide layer by the gas evolution at SiC-SiO2 interface. Pitting corrosion has found at open pores and grain boundaries.