• 한국주조공학회지
• /
• 제20권1호
• /
• pp.13-20
• /
• 2000

In the present study,($10%Al_2O_3+5%Si$)/AZ91 Mg hybrid composite was fabricated using the squeeze casting method. During squeeze casting, Molten Mg was infiltrated into the preform of $10%Al_2O_3+5%Si$ and reaction product of $Mg_2Si$ intermetallic compound was formed by the reaction between molten Mg and Si Powder. Microstructure has been observed and mechanical properties were evaluated for the reaction squeeze cast(RSC) hybrid composite. It was found that Si powder totally reacted with molten Mg to form $Mg_2Si$. Reinforcement($Al_2O_3$) and the reaction product ($Mg_2Si$) are fairly uniformly distributed in Mg Matrix for the squeeze cast hybrid composite. Mechanical Properties were improved with hybridization of reinforcements, namely higher hardness and enhanced wear resistance comparing squeeze cast($15%Al_2O_3$)/AZ91 Mg composite.

• 한국세라믹학회지
• /
• 제27권4호
• /
• pp.501-512
• /
• 1990

Al2O3 and 0.25wt% MgO-doped Al2O3 powders were made from the alcohol solution of Al(NO3)3.9H2O and Mg(NO3)2.6H2O by spray pyrolysis method. Each powder was prepared at 900 and 100$0^{\circ}C$. Powders prepared at 90$0^{\circ}C$ were amorphous phase, but prepared at 100$0^{\circ}C$ wre mainly ${\gamma}$-Al2O3 crystalline form. Particle size of the MgO-doped Al2O3 powders was in the range of 0.2-2${\mu}{\textrm}{m}$, but undooped powders shwoed comparatively wider range of particle size. All the powders prepared at 900 and 100$0^{\circ}C$ were transformed to $\alpha$-Al2O3 crystalline form by calcination at 110$0^{\circ}C$ for 1hr. Each powder was sintered at 1600, 1650 and 1$700^{\circ}C$ for 2hrs. MgO-doped Al2O3 body sintering at 1$650^{\circ}C$ showed 99% of relative density but undooped Al2O3 showed 95% of relative density, even sintered at higher temperature of 1$700^{\circ}C$.

• 한국세라믹학회지
• /
• 제36권4호
• /
• pp.410-416
• /
• 1999

The reactivity of three kinds of spinels which CaO-Al2O3-SiO2 slag was investigated in terms of mineral phases and microstructures. New crystal products were not formed by reaction of 12CaO.7Al2O3 in the slag with spinels and free MgO components was preferenctially dissolved into slag for MgO-rich spinel and stoichiometric spinel. Meanwhile mineral phase was changed from 12CaO.7Al2O3 to CaO.Al2O3 to CaO.2Al2O3 finally to CaO.6Al2O3 having high melting point for Al2O3 -rich spinel. The Fe-oxide component of the slag was taken up by only stoichiometric spinel grains within the spinel clinker and the trapped amount of Fe-oxide was independent of MgO content of MgO in spinel clinker the more th resistance to slag corrosion but the less resistance to slag penetration.

• 한국주조공학회지
• /
• 제16권6호
• /
• pp.556-564
• /
• 1996

Variation of shape and size of solid particles and solute redistribution in Mg-9wt.%Al, AI-4.5wt.% Cu, and AI-7wt.%Si alloys were investigated when they were heated to semi-solid temperatures and held without stirring. In the case of Mg-9wt.% Al and Al-4.5wt.%Cu alloys, the polygonal shaped solid particles were agglomerated with non-uniform distribution, and there were no disappearance of the solid/solid boundary until the end of melting. But in the case of an Al-7wt.%Si alloys, two or three spherical shaped particles were coalesced or separated individually, and the coalesced particles had no solid/solid interface on the contrary to the prevous case. The maximum size of solid particles during isothermal heating at high temperature was smaller than that at lower temperature, but the time required to reach the maximum size at high temperature was shorter than that at lower temperature. The concentrations of main solute atom whose distribution coefficient is lower than 1, decreased in the primary solid particles as the liquid fraction increased, and the gradient of solute concentration was steeper in Mg-9wt.%Al alloy and Al-4.5wt.%Cu alloy than that of Al-7wt.%Si alloy.

• 동력기계공학회지
• /
• 제5권4호
• /
• pp.74-81
• /
• 2001

The infiltration behavior of molten Al-alloy, microstructures, hardness, and the interfacial reactions of $SiC_p/Al$ composites fabricated by the pressureless infiltration technique were investigated. It was made clear that both the weight fraction of SiC reinforcement and additive Mg content considerably influenced on the infiltration behavior of the molten Al-alloy matrix. Complete infiltration of molten Al-alloy achieved under the conditions that weight fraction of SiC content is more than 30wt%, and additive Mg content is more than 9wt%. Interfacial region of Al-alloy matrix and SiC reinforcement phase, $Mg_2Si$ was formed by the reaction between Mg and SiC. Another reaction product AlN was also formed by the reaction between Al-alloy matrix and gas atmosphere nitrogen.

• 한국표면공학회지
• /
• 제39권1호
• /
• pp.25-34
• /
• 2006

Al-Mg alloy, an open rack vaporizer(ORV) material was reported to be corroded in seawater environments though the ORV material was coupled to thermally sprayed Al-Zn alloy functioning a sacrificial anode. In addition, the corrosion behavior based on the calculated corrosion potential did not match the observed corrosion behavior. Hence, the goal of this study is to get better understanding on Al or Al-Mg alloy coupled to Al-Zn alloy and to provide the calculated corrosion potential representing the corrosion behavior of the ORV material by immersion test, electrochemical tests, and calculation of corrosion and galvanic potential. The corrosion potentials of Al and Al alloys also depended on alloying element as well as surface defects. The corrosion potentials of Al and Al-Mg alloy were changed with time. In the meantime, the corrosion potentials of Al-Zn alloys were not. The corrosion rates of Al-Zn alloys were exponentially increased with zinc contents. The phenomena were explained with the stability of passive film proved by passive current density depending on pH and confirmed by the model proposed by McCafferty. Dissimilar material crevice corrosion (DMCC) test shows that higher content of zinc caused Al-Mg alloy corroded more rapidly, which was due to the fact that higher corrosion rate of Al-Zn makes [$H^+$] and [$Cl^-$] more concentrated within pit solution to corrode Al-Mg alloy. Considering electrochemical reactions within pit as well as bulk in the calculation gives better prediction on the corrosion behavior of Al and Al-Mg alloy as well as the capability of Al-Zn alloy for corrosion protection.

• 한국주조공학회지
• /
• 제29권6호
• /
• pp.265-269
• /
• 2009

The optimum RRA heat treating conditions and SCC (stress corrosion cracking) resistance of semi-solid Al-Zn-Mg-Cu alloy fabricated by inclined cooling plate were compared with those of conventional mould cast alloys. The non-stirring method characterized by using a cooling plate can effectively eliminate dendritic structure and form a fine globular semisolid microstructure in as-cast Al-Zn-Mg-Cu alloy and the SCC resistance of semi-solid Al-Zn-Mg-Cu alloy was higher than that of conventional mold cast alloy. Also, after retrogressed treatment at RRA heat treatment of semi-solid Al-Zn-Mg-Cu alloy, retrogressed treatment time has increased more than 10 minutes at $180^{\circ}C$ to recovery the T6 heat treatment strength.

• 한국세라믹학회지
• /
• 제25권1호
• /
• pp.35-41
• /
• 1988

In the system of Li2O-MgO-Al2O3-Cr2O3, the crystalline solid solution of LiCrO2 along the pseudo-binary join between rocksalt structure(LiCrO2) and spinel structure(MgCr2O4 or MgAl2O4) have been investigated by x-ray diffraction techniques. In this study, order-disorder phase transition of LiCrO2 was observed and the unit cell of the disordered LiCrO2 structure has been established. It has been found that LiCrO2 makes a solid solution over a wide range with MgAl2O4, while not with MgCr2O4. This difference was explained as being due to the ability of oxygen lattice distortion which depended on the relative sizes and chemical bonding characteristics of the substituted ions.

• 한국응용과학기술학회지
• /
• 제35권3호
• /
• pp.757-767
• /
• 2018

고온에서 진행되는 프로판 탈수소 반응에서 촉매의 불활성화의 주된 원인은 코크 침적, 소결현상이 있다. 이러한 불활성화를 줄이는 촉매를 연구하기 위해, 본 연구에서는 열적 안정성이 높은 $MgAl_2O_4$ 를 담체로 적용하여 프로판 탈수소 반응용 촉매로의 활용성을 확인하고자 하였다. Alcohthermal method로 $MgAl_2O_4$를 소성온도 800, 900, $1000^{\circ}C$로 달리하여 제조하였고, Pt와 Sn을 공동함침법으로 담지하여$Pt-Sn/MgAl_2O_4$촉매를 제조하였다. 열적안정성의 확인을 위해 반응온도를 고온의 650, $600^{\circ}C$에서 진행하였다. 반응실험 결과 반응온도에 상관없이 담체의 소성온도가 $800^{\circ}C$인 담체적용 촉매일 때 프로판 탈수소반응 실험의 전환율과 수율이 담체소성온도가 900, $1000^{\circ}C$인 담체적용 촉매보다 높은 것을 확인하였고, 반응온도가 고온인 $650^{\circ}C$일 때는 $Pt-Sn/{\theta}-Al_2O_3$보다도 더 높은 수율을 가지는 것을 볼 수 있었다. 특성분석으로는 TGA, BET, XRD, CO-화학흡착, SEM-EDS 분석을 실시하였다. $MgAl_2O_4-800^{\circ}C$가 좋은 수율과 Pt분산도 및 적은 불활성화 정도의 관계를 서로 연관 지어 확인하였다.

• 자원리싸이클링
• /
• 제29권6호
• /
• pp.65-72
• /
• 2020

블랙 드로스는 알루미늄을 재활용하는 과정 중에 플럭스 사용에 의해 발생되는 짙은 회색의 드로스로서, NaCl, KCl, Al2O3, MgO 등이 포함되어 있다. 블랙 드로스는 용해(dissolution) 공정을 통하여 용해성 물질(NaCl, KCl)과 불용해성 물질(Al2O4, MgO)로 분리가 가능하다. 이중 용해성 물질의 경우 Salt flux로 재활용이 가능하며, Al2O3, MgO의 경우 합성 공정을 통하여 다양한 세라믹 소재로 업사이클링이 가능하다. 본 연구에서는 블랙 드로스로부터 회수한 Al2O3, MgO를 이용하여 Mayenite를 합성 하였으며, 배합 비율 및 반응 온도 조건에 따른 합성을 실시하였다. 블랙 드로스(spinel)와 CaCO3를 이용하여 Mayenite를 합성할 시 700 ℃에서 Mg0.4Al2.4O4, CaO로 변하며, 800 ℃ 이후부터 Ca12Al14O33(Mayenite)으로 변하는 것을 확인하였다. 배합 조건에는 CaCO3 함량이 증가함에 따라 Mayenite XRD 피크가 증가하며, Mg0.4Al2.4O4 XRD 피크는 감소하는 것을 확인하였다. 합성된 분말의 BET 분석 결과 Mayenite가 생성되는 과정에서 미세한 입자가 성장되고 응집됨에 따라 비표면적은 감소하는 거동을 보였다.