• Journal of the Korean earth science society
• /
• v.25 no.6
• /
• pp.474-483
• /
• 2004

This paper analyzed the characteristics of daily ozone variations over Kangreung and Wonju. It was found that the diurnal cycle of ozone over Wonju has a primary ozone peak in the afternoon and a minimum around sunrise, which is a typical diurnal ozone cycle observable in the urban area. However, the cycle over Kangreung shows a primary peak in the afternoon and secondary peak around 3 a.m. The amounts of ozone in the secondary peak is occasionally higher than that in the primary peak. This nocturnal ozone peak is frequently observed year-round, and the highest frequency and extent are observed in spring. The possible cause of this nocturnal ozone increase was investigated using meteorological parameters and the HYSPLIT trajectory model. It was found that the nocturnal ozone peak is highly correlated with strong wind speed, which has led to positive temperature anomaly. The trajectory model revealed that when the secondary peak occurred, the air was originated from the west and a sinking motion subsequently followed. These findings suggested that when the westerly wind is strongest in spring, the polluted airs from urban areas are transported to the upper boundary layer over Kangreung area. In the case of strong wind during the night, nocturnal ozone peaks were produced by active vertical mixing between lower boundary and upper boundary layers.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.31 no.12
• /
• pp.1662-1671
• /
• 2007

The change in physical properties of polypropylene nonwoven fabrics used as top sheet for disposable sanitary goods was carried out using chitosan that is a type of natural polymer and has excellent human affinity by varying the molecular weight and concentration of chitosan. Low molecular weight(LMW) chitosan treated fabrics were found to be evenly coated on fabrics and had better dyeability by apparent dye uptake and its deodorization rate increased over the time. On the other hand, high molecular weight(HMW) chitosan treated fabrics showed higher add-on ratio and its dynamic water absorption rate and represented an increase in water transport rate. With chitosan treatment, its air permeability was improved. Regardless of the type of bacteria and chitosan concentration, its antibacterial activity was excellent in the case of the HMW chitosan treatment. In this regard, chitosan treatments by using a relatively high molecular weight was found as an effective way in the functional improvement of moisture properties and antibacterial activity including their most important performance in sanitary nonwoven fabrics.

• Journal of the Korea Convergence Society
• /
• v.11 no.6
• /
• pp.237-248
• /
• 2020

The purpose of this study is to measure the agricultural product market efficiency of the three e-commerce platforms from the perspective of consumer price fairness perception, analyze the quality and price gap of invalid brands, and help agricultural products enterprises to formulate reasonable price strategies. The characteristics of farm products sold in e-commerce platforms(quality, origin, taste, safety level) were selected as output indicators and the prices of products were selected as input indicators to evaluate the efficiency of the market through DEA analysis. According to the analysis, JD mall has the largest proportion of effective brands, while YHD.com has the highest average market efficiency, and northeast rice has the largest difference in average efficiency among the three platforms. The results show that price inefficiencies still exist in the electronic market. The development of online market for agricultural products should pay attention to consumer price fairness and pay attention to the coordination between price and quality. The limitation of this paper is that it does not focus on the influence of words of mouth marketing in internet market and consumer experience, which can be the future research direction.

• Atmosphere
• /
• v.25 no.2
• /
• pp.221-233
• /
• 2015

Pollen is closely related to health issues such as allergenic rhinitis and asthma as well as intensifying atopic syndrome. Information on current and future spatio-temporal distribution of allergenic pollen is needed to address such issues. In this study, the Community Multiscale Air Quality Modeling (CMAQ) was utilized as a base modeling system to forecast pollen dispersal from oak trees. Pollen emission is one of the most important parts in the dispersal modeling system. Areal emission factor was determined from gridded areal fraction of oak trees, which was produced by the analysis of the tree type maps (1:5000) obtained from the Korea Forest Service. Daily total pollen production was estimated by a robust multiple regression model of weather conditions and pollen concentration. Hourly emission factor was determined from wind speed and friction velocity. Hourly pollen emission was then calculated by multiplying areal emission factor, daily total pollen production, and hourly emission factor. Forecast data from the KMA UM LDAPS (Korea Meteorological Administration Unified Model Local Data Assimilation and Prediction System) was utilized as input. For the verification of the model, daily observed pollen concentration from 12 sites in Korea during the pollen season of 2014. Although the model showed a tendency of over-estimation in terms of the seasonal and daily mean concentrations, overall concentration was similar to the observation. Comparison at the hourly output showed distinctive delay of the peak hours by the model at the 'Pocheon' site. It was speculated that the constant release of hourly number of pollen in the modeling framework caused the delay.

• Atmosphere
• /
• v.22 no.1
• /
• pp.29-45
• /
• 2012

An unusual autumn storm developed rapidly in the western part of the East sea on the early morning of 23 October 2006. This storm produced a record-breaking heavy rain and strong wind in the northern and middle part of the Yeong-dong region; 24-h rainfall of 304 mm over Gangneung and wind speed exceeding 63.7 m $s^{-1}$ over Sokcho. In this study, MTSAT-1R (Multi-fuctional Transport Satellite) water vapor and infrared channel imagery are examined to find out some features which are dynamically associated with the development of the storm. These features may be the precursor signals of the rapidly developing storm and can be employed for very short range forecast and nowcasting of severe storm. The satellite features are summarized: 1) MTSAT-1R Water Vapor imagery exhibited that distinct dark region develops over the Yellow sea at about 12 hours before the occurrence of maximum rainfall about 1100 KST on 23 October 2006. After then, it changes gradually into dry intrusion. This dark region in the water vapor image is closely related with the positive anomaly in 500 hPa Potential Vorticity field. 2) In the Infrared imagery, low stratus (brightness temperature: $0{\sim}5^{\circ}C$) develops from near Bo-Hai bay and Shanfung peninsula and then dissipates partially on the western coast of Korean peninsula. These features are found at 10~12 hours before the maximum rainfall occurrence, which are associated with the cold and warm advection in the lower troposphere. 3) The IR imagery reveals that two convective cloud cells (brightness temperature below $-50^{\circ}C$) merge each other and after merging it grows up rapidly over the western part of East sea at about 5 hours before the maximum rainfall occurrence. These features remind that there must be the upward flow in the upper troposphere and the low-layer convergence over the same region of East sea. The time of maximum growth of the convective cloud agrees well with the time of the maximum rainfall.

• Tunnel and Underground Space
• /
• v.9 no.4
• /
• pp.306-314
• /
• 1999

In underground spaces including nuclear waste repository, prediction of air quantity, temperature/humidity and pollutant concentration is utmost important for space construction and management during the normal state as well as for determining the measures in emergency cases such as underground fires. This study aims at developing a model for underground space environment which has capabilities to take into account the effects of autocompression for the natural ventilation head calculation, to find the optimal location and size of fans and regulators, to predict the temperature and humidity by calculating the convective heat transfer coefficient and the sensible and latent heat transfer rates, and to estimate the pollutant levels throughout the network. The temperature/humidity prediction model was applied to a military storage underground space and the relative differences of dry and wet temperatures were 1.5 ~ 2.9% and 0.6 ~ 6.1%, respectively. The convection-based pollutant transport model was applied to two different vehicle tunnels. Coefficients of turbulent diffusion due to the atmospheric turbulence were found to be 9.78 and 17.35$m^2$/s, but measurements of smoke and CO concentrations in a tunnel with high traffic density and under operation of ventilation equipment showed relative differences of 5.88 and 6.62% compared with estimates from the convection-based model. These findings indicate convection is the governing mechanism for pollutant diffusion in most of the tunnel-type spaces.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.10
• /
• pp.649-657
• /
• 2017

A rupture in a high-pressure pipe causes the fluid in the pipe to be discharged in the atmosphere at a high speed resulting in a supersonic jet that generates the compressible flow. This supersonic jet may display complicated and unsteady behavior in general. In this study, Computational Fluid Dynamics (CFD) analysis was performed to investigate the compressible flow generated by a supersonic jet ejected from a high-pressure pipe. A Shear Stress Transport (SST) turbulence model was selected to analyze the unsteady nature of the flow, which depends upon the various gases as well as the diameter of the pipe. In the CFD analysis, the basic boundary conditions were assumed to be as follows: pipe of diameter 10 cm, jet pressure ratio of 5, and an inlet gas temperature of 300 K. During the analysis, the behavior of the shockwave generated by a supersonic jet was observed and it was found that the blast wave was generated indirectly. The pressure wave characteristics of hydrogen gas, which possesses the smallest molecular mass, showed the shortest distance to the safety zone. There were no significant difference observed for nitrogen gas, air, and oxygen gas, which have similar molecular mass. In addition, an increase in the diameter of the pipe resulted in the ejected impact caused by the increased flow rate to become larger and the zone of jet influence to extend further.

• Journal of Chest Surgery
• /
• v.13 no.2
• /
• pp.85-91
• /
• 1980

Extracorporeal circulation by hemodilution technique has been currently used with its clinical safety and good peripheral tissue perfusion in open heart surgery. There is no doubt that $O_{2}$ carrying capacity of the blood is disturbed by decreased hemoglobin level resulting from hemodilution of the circulating blood. From the view point of the blood gas exchange, these experimental studies were undertaken to determined the sate limit of hemodilution in the condition of cardiopulmonary bypass with a constant perfusion flow rate. Twelve adult mongrel dogs weighing 10 to 13 Kg. were anesthetized with pentobarbital and then respiration was controlled with Harvard volume respirator using room air. The cardiopulmonary by pass was performed by use of Sarns heart lung machine (console 5000, 5 head and 2 roller pumps) and Travenol pediatric bubble oxygenator. The perfusion rate during bypass was maintained at a constant rate of 80 ml/min/Kg of body weight. The ratio of oxygen gas flow to blood flow was kept in 3 to 1 constantly. International hemodilution was attained by serial blood withdrawals and immediate infusion of equal volumes of diluants composed of Ringer's lactate, 5% dextrose in water and 25% mannitol solution, proportionally 60%, 30%, and 10%. Arterial and venous blood samples were obtained between 15 and 20 minutes following each hemodilution. Hematocrits and hemoglobin values, $PO_{2}$, $PCO_{2}$ and pH were measured. Oxygen and carbon dioxide contents oxygen consumption and carbon dioxide elimination were calculated groups according to different hematocrit values and the correlations were evaluated. Result were as follows. 1. the arterial $O_{2}$ tension and $O_{2}$ saturation were maintained at the physiological level irrespective of the hematocrit value. 2. The venous $O_{2}$ tension and $O_{2}$ saturation showed a tendency to decline with the decrease in hematocrit value and positive correlation between them (r = +0.49, r = +0.76), The mean values of venous $O_{2}$ tension and $O_{2}$ saturation, however, were not decreased when the hematocrit levels were lower than 20%. 3. The arterial $O_{2}$ content declined lineally in proportion to the fall of hematocrit level with a positive correlation between them (r = +0.95). 4. The venous $O_{2}$ contents were decreased gradually as the hematocrit value decreased with positive correlation between them ( r =+0.89). The trend of diminution of venous $O_{2}$ content, however, was became low according to progressive decrease of hematocrit level. 5. Systemic oxygen consumption was in higher range than $O_{2}$ requirement of basal metabolism when the hematocrit value was above 20%, but abruptly decreased when the hematocrit value became to below 20%. 6. The arterial $CO_{2}$ tension and $CO_{2}$ content showed trend of increasing with progressive decrease of hematocrit value but exhibited a rather broad range and there was no relationship between those value and the hematocrit value. 7. The venous $CO_{2}$ tension and $CO_{2}$ content have also no correlation with change of Ht. value but related directly to those value of arterial blood with positive correlation between them (r = +0.78, r = +0.95_. 8. A-V difference of $CO_{2}$ content and $CO_{2}$ elimination wasnot significantly influenced by Ht. value. From the results, we obtained that feasible limit in inteneional hemodilution is above the hematocrit value of 20% under the given experimental condition.

• Journal of Distribution Science
• /
• v.14 no.5
• /
• pp.51-57
• /
• 2016

Purpose - In the year of 2015 and 2016, one of the items that got attention in CES was a drone. It has been 100 years since a drone emerged, but most were used for military purposes. As its use became diverse as of 2010, it got attention of the general public. In Korea, it was in 2011 that a drone was known to the public through an aerial video shooting for television program. This study tried to come up with suggestions by comparing domestic with overseas cases, and tried to consider the related technologies and systems with applying the role of drones in logistics service. Research design, data, and methodology - The overseas cases were regarded as drone's logistical purpose. The Prime Air service by US Amazon is still not commercialized and under pre-testing due to Federal Aviation Regulations, although it started in 2013. In Germany, DHL succeeded in delivering service testing which is called Parcelcopter, but it is not commercialized yet. Other than these, there are more attempts to prepare logistics service in China with Taobao, in France with Geopost's test, and in Africa. In Korea, CJ Korea Express tested delivery with a self-developed drone Results - In order to study for utilizing drones for logistics as the prerequisites, some overseas and domestic cases, which are currently considered, were reviewed. Also, the technologies and institutional requirements to commercialize drones for logistical purpose were reviewed. The reasons for using drones in logistics is to ensure the price competitiveness by reducing cost. The empirical test also will be needed because drone pilot areas are designated by ministry of land, infrastructure and transport. Conclusions - In order to utilize drones in logistics and foster the industry, this study would like to suggest the followings. First of all, size of drones for logistics needs to be fixed and their operating system should be standardized. Centralized investment resources are needed through standardization to ensure the market occupancy. Secondly, it is necessary to get the converged businesses that do research, develop and commercialize drones with the investment of private sector. Example can be found in Korea aerospace Industries. We can respond to the rapid growth of the market with intensive investing by integrating the private sector investment. Thirdly, institutional arrangements are needed to be established quickly. In the case of high-technologies like drones, institutional support often does not follow the rapid development of the technology. The problems can be found in securing drones-only airspace, creating drone-specialized pilot's license, matters related to remote controller and complementary regulations for drones in Aviation Act. If these regulations are not prepared or complemented at the right timing, technologies cannot be commercialized even though the development is completed. Fourthly, there is a need to secure the transparency regarding possible privacy and personal information protection problem while operating drones. Finally, in order to foster this new industry, government should focus on supporting R&D more in the long term than short term outcomes.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.8 no.4
• /
• pp.251-258
• /
• 2014

A wheelchair is a typical mobility aid for the physically disabled or the old and the weak, and is the most commonly used rehabilitation aid. In general, most of users of manual wheelchair have difficulty though vocational rehabilitation and independent living is possible. The reason is that long-distance movement is always accompanied with wheelchair transfer problem because a wheelchair is used as direct means of transport. Hence, the wheelchair transfer problem should be first solved in order that a wheelchair user can independently live. Therefore, this study examined and analyzed the domestic and overseas launched products and patented technologies of wheelchair transfer system for vehicle, and proposed a wheelchair transfer mechanism of a new system for vehicle. This study proposed a wheelchair transfer mechanism for vehicle in order to remove the disadvantage of wheelchair transfer system for vehicle to support the conventional wheelchair user's movement, and in order to conform with the structure of domestic welfare vehicle for the disabled. Because a difference between storage space installed in the roof of vehicle and storage space for leisure, which is generally utilized, gets to disappear by applying this proposed mechanism, popularity among users can be increased. And storage space that has become smaller like this will be capable of decreasing the disadvantage of air resistance in traveling. Besides, because of getting to conform with the structure of welfare vehicle, restrictions on the application range will disappear from small sedan to SUV. Therefore, users can have more choices.