• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.451-454
• /
• 2009

Production and application of biodiesel are expected to grow steadily in the coming years and thus output of its by-product, crude glycerin, will accordingly increase as well. In the present study, gasification of biodiesel by-product as a renewable energy was performed in an entrained flow gasifier to investigate the gasification performance with the operating conditions. Crude glycerin shows a high heating value of 6,000 kcal/kg and low ash and sulphur content. Gasification was conducted in a temperature range of $950\;{\sim}\;1500\;^{\circ}C$. The variation of syngas composition with excess air ratio of 0.17 ~ 0.7 for air or oxygen as a gasification agent was investigated. From the results, syngas heating value, carbon conversion and cold gas efficiency of more than $2500\;kcal/Nm^3$, 95% and 65% were achieved, respectively. The temperature dependency of syngas composition, carbon conversion, and cold gas efficiency shows a similar tendency to excess air ratio at the temperature corresponding to the excess air ratio. The $H_2/CO$ ratio of the product gas was varied from 1.25 to 0.7 with the excess air ratio and this gas composition was favorable for DME synthesis. The optimum excess air ratio for gasification of biodiesel by-product was evaluated to be an approximately 0.35 to 0.4. The present results indicate that crude glycerin can be utilized as a feedstock for gasification to make syngas.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.48 no.3
• /
• pp.63-71
• /
• 2006

A downdraft gasifier was made of stainless steel for biomass gasification. Internal reactor had a 300 mm diameter and 8 air intakes. Three thermocouples were installed to measure the temperature inside the reactor. Three different biomass fuels were provided in the experiments to find out the effects of fuel conditions on gasification processes; charcoals, woodchips, and mixture of woodchip and charcoals. Two different experiments were conducted fer charcoal experiments, small and larger sizes of charcoal fuels. It took about 10 minutes after ignition to generate combustible producer gas when charcoal was f9d, but 20 or more minutes for woodchips. When the gasification was stabilized, the highest temperature was observed just below the combustion zone. The air flow rate for woodchip experiment was provided at 25% of a stoichiometric requirement of combustion, which was within the range of typical air flow rate fer woody biomass gasification. Carbon monoxide concentrations were also within the values reported in the previous studies, ranging 20 to 30% depending on fuel types. It could be seen that fuel size and heating value were very important parameters in biomass gasification. These parameters should be taken into account in operating and designing biomass gasifiers.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.129.2-129.2
• /
• 2010

As a part of the government renewable energy policy, KOWEPO is constructing 300MW IGCC plant in Taean. IGCC plant consists of gasification block, air separation unit and power block, which performance test is separately conducted. Overall performance test for IGCC plant is peformed to comply with ASME PTC 46. Major factors affected on the overall efficiency for IGCC plant are external conditions, each block performance(gasification, ASU, power block), water/steam integration and air integration. Performance parameters of IGCC plant are cold gas efficiency, oxygen consumption, sensible heat recovery of syngas cooler for gasification block and purity of oxygen, flow amount of oxygen and nitrogen, power consumption for air separation unit and steam/water integration among the each block. The gas turbine capacity applied to the IGCC plant is 20 percent higher than NGCC gas turbine due to the low caloric heating value of syngas, therefor it is possible to utilize air integration between gas turbine and air separation unit to improve overall efficiency of the IGCC plant and there is a little impact on the ambient condition. It is very important to optimize the air integration design with consideration to the optimized integration ratio and the reliable operation. Optimized steam/water integration between power block and gasification block can improve overall efficiency of IGCC plant where the optimized heat recovery from gasification block should be considered. Finally, It is possibile to achieve the target efficiency above 42 percent(HHV, Net) for 300MW Taean IGCC plant by optimized design and integration.

• Journal of Environmental Science International
• /
• v.15 no.6
• /
• pp.601-606
• /
• 2006

The coal gasification fuel is important to replace petroleum fuel. Also they have many benefits for reducing the air pollution. Measurements on the combustion characteristics of synthetic gas from coal gasification have been conducted as compared with LPG in constant volume combustion chamber. The fuel is low caloric synthetic gas containing carbon monoxide 30%, hydrogen 20%, carbon dioxide 5%, and nitrogen 45%. To elucidate the combustion characteristics of the coal gasification fuel, the combustion pressures, combustion durations, and pollutants(NOx, $CO_2$, CO) are measured with equivalence ratios($\phi$), and initial pressures of fuel-air mixture in constant volume chamber. In the case of the coal gasification fuel, maximum combustion pressure and NOx concentration are lower rather than LPG fuel. However CO and $CO_2$ emission concentration are similar to that of LPG fuel.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.11
• /
• pp.3205-3208
• /
• 2014

Catalytic gasification of cellulose was carried out in a U-type fixed reactor with Ni loaded MSU-F catalyst (Ni/MSU-F) and Ni loaded ${\gamma}-Al_2O_3$ (Ni/${\gamma}-Al_2O_3$). The characteristics of the catalysts were analyzed by using X-ray diffraction, $H_2$-temperature programmed reduction, and Brunauer-Emmett-Teller analyses. The operation conditions of catalytic gasification reactions were $750^{\circ}$ and 0.2 equivalence ratio. Air was used as gasification agent. Catalytic gasification characteristics, such as gas yield and gas composition ($H_2$, CO, $CO_2$, $C_1-C_4$), were measured and calculated. The gas yield of Ni/MSU-F was much higher than that of Ni/${\gamma}-Al_2O_3$. Especially high amount of hydrogen was produced by Ni/MSU-F.

• 한국연소학회:학술대회논문집
• /
• 2007.05a
• /
• pp.63-68
• /
• 2007

An experimental study was carried out to investigate gasification process of wood sawdust in the 1-dimensional downdraft fixed bed gasifier. The preheated air which was used oxidizer and steam were used as a gasifying agent. The downdraft fixed bed gasifier obtains more amount of hydrogen and methane by increasing residence time of supplied air. The operating parameters, the supplied air temperature and steam were used. The oxidizer temperature was varied from 500K to 620K and vapor was added. The gasification process was monitored by measuring temperature at three position near the biomass using R-type thermocouples and the syngas composition was analyzed by gas chromatograph. We get the sample gas at the end of gasifier and it was eonugh time to finishing the chemical reaction. Finally, the amount of hydrogen and methane were increased widely as increasing the oxidizer temperature and adding steam.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.64 no.5
• /
• pp.1-8
• /
• 2022

Hydrogen can be produced by gasification of biomass and other combustible fuels. Depending on oxydant agents, syngas or producer gas compositions become quite different. Since biomass has limited amount of hydrogen including moisture in it, the hydrogen concentration in the syngas is about 15% when air is supplied for oxidant agent. Experiments were conducted to investigate the channges in hydrogen concentrations in syngas with different oxidant agent conditions, fuel conditions, and external heat supply. Allothermal reaction resulted in higher concentrations of hydrogen with the supply of steam over air, reaching over 60%. Hydrogen is produced by water-gas and water-gas shift reactions. These reactions are endothermic and require enough heat. Autothermal reaction occurred in the downdraft gasifier used in the experiment did not provide enough heat in the reactions for hydrogen production. Steam seems a more desirable oxidant agent in producing the syngas with higher concentrations of hydrogen from biomass gasifications since nitrogen is included in syngas when air is used.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.11
• /
• pp.80-85
• /
• 2021

The gasification of coffee leaves, which are a type of biomass waste, was conducted on a pilot of a downdraft fixed gasification system to investigate the gasification characteristics. The experiment was performed using a coffee leaf pellet size and a batch-type gasification system consisting of a gasifier, cooling cyclone, scrubber, and bag filter. It was found that the air-to-fuel ratio was 2.32 Nm³/kg·h and the reaction temperature was 700 ℃-900 ℃. However, the air flow rate changed to 0.45 Nm³/min, which was lower than the initial starting value depending on the temperature change during the gasification process. It was concluded that coffee leaves can be converted from biomass waste into useful synthetic gas as an alternative energy source.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.238-243
• /
• 2004

High temperature air blown gasification is new concept to utilize the waste heat from gasifier that is called the multi-staged enthalpy extraction technology. This process was developed to solve the economic problem due to air separation cost for the oxygen-blown as a gasifiying agent. In this study, we have performed the construction of pebble bed gasifier and operated it by controlling the pebble size and bed height. As a result, we can produce the syngas with the calorific value of 700kcal/$Nm^3$ at the condition of air temperature 650$^{\circ}C$.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3429-3434
• /
• 2007

An experimental study was carried out to investigate gasification process of wood sawdust in the I-dimensional downdraft fixed bed gasifier. The preheated air was used oxidizer and steam were used as a gasifying agent. The operating parameters, the supplied air temperature and steam were used. The oxidizer temperature was varied from 500K to 620K and vapor was added. The gasification process was monitored by measuring temperature at three position near the biomass using R-type thermocouples and the syngas composition was analyzed by gas chromatograph. The change of hydrogen and carbon monoxide, carbon dioxide, methane was observed. Overall, the volume fraction of hydrogen and methane were increased widely as increasing the oxidizer temperature and adding steam.