• 한국약용작물학회지
• /
• 제26권4호
• /
• pp.291-295
• /
• 2018

Background: The use of Rehmannia glutinosa of the family Scrophulariaceae, in traditional medicine is well known. This study was conducted to elucidate the effect of air curing of the seed rhizome of R. glutinosa on its storability and yield. Methods and Results: The root of the R. glutinosa cultivar (Dagang) was harvested in at the end of November. The seed rhizomes were air cured for one to seven days. They were subsequently wrapped with newspaper and further stored in a plastic container at $1^{\circ}C$. It was observed that the weight loss and decay rates were significantly lower in the air cured seeds than in the untreated ones. Moreover, the decay rate of the control was approximately 50%, 120 days after storage. However. the decay rate of all the air cured treatment groups was less than 1%. Additionally, air curing led to an increase in the germination rate of the seeds and the root yield when compared with the untreated groups. Taken together, the ideal treatment period for air curing was found to be 3 days. Under these conditions, the germination rate and yield were 88.7% and 2,185 ㎏/10a, respectively. Conclusions: This study successfully demonstrated that the air curing of seed rhizomes can lead to a considerable increase in the storability and yield of R. glutinosa.

• 생물환경조절학회지
• /
• 제20권4호
• /
• pp.304-310
• /
• 2011

본 연구는 기존의 농가 보급형 고구마 저장고에 가열기(본체), 환기팬, 배풍구 팬, 습도 조절을 위한 관으로 구성된 간이 큐어링 설비를 부가시킨 후, 그 효과를 검증하기 위하여 수행되었다. 6일간의 큐어링 처리 기간 동안 저장고 내 기온 및 상대습도는 $32^{\circ}C$, 90%로 설정되었다. 고구마의 저장 기간(6 개월) 동안 1개월에 1회씩 표본을 수집하여 물리화학적 품질을 측정한 결과, 부패율과 부패 정도를 함께 보여주는 McKinney Index는 큐어링 처리구의 경우 0.83%였으며, 큐어링 처리를 하지 않은 대조구의 경우 5.08%였다. 큐어링 처리구의 경도 및 당도, 건물율은 모두 대조구보다 높았으며, 대조구의 표피색이 큐어링 처리구보다 빠르게 변하여 큐어링 처리가 저장기간 동안 고구마의 변색을 지연시켰음을 알 수 있었다. 본 연구를 통하여 간이 큐어링 설비를 이용한 큐어링 처리는 초기 비용이 많이 소모되는 일반 큐어링 설비를 대체하여 고구마의 물리화학적 품질을 증진시킬 수 있으며, 저장 기간을 늘릴 수 있음을 알 수 있었다.

• 품질경영학회지
• /
• 제16권1호
• /
• pp.43-48
• /
• 1988

Most of silicone used for water repellent finish is MHP (methyl hydrodiene polysiloxane), which is formed by hydrolysis and condensation polymerization of MHD (methyl hydrodiene dichlorosilane: Me H Si $Cl_2$). The cross-linking theory explains the water repellent mechanism of MHP. The silicone finish on fiber could improve in handle, softness, abrasion resistance, soil repellency, tear strength and crease resistance, as well as water repellency. According to using method silicone-water repellent finishing agents, could be devided into air dry type and curing type. MHP is the typical curing type of water repellent finishing agent, and this type requires the curing temperature above $150^{\circ}C$ at least. High curing temperature is the very drawback of this curing type. For this reason, there has been global interest in the lowering of its temperature. The objective of this study is to investigate merits of alkali treatment for silicone finishing by ANOVA and LSD (least significant difference).

• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.629-637
• /
• 2023

This study aimed to evaluate the effect of post-curing equipment and time on the flexural strength of 3D printing resins produced by a liquid crystal display(LCD) printer. The three 3D printing resins(DENTCA Denture Teeth, DT; C&B 5.0 hybrid, CH; C&B Permanent A2, CP) were divided into four groups according to post-curing time(10 min and 30 min) and equipment with or without vacuum treatment. For the three-point flexural strength test and biaxial strength test were prepared by method according to ISO 10477, ISO 6872, respectively. Flexural strength was measured with universal testing machine. Comparison between post-curing time of each post-curing equipment was analyzed by independent sample t-test and Mann-Whitney U test(α=.05), and comparison between groups according to each 3D printing resin was performed by Kruskal-Wallis test and post-hoc by Bonferroni-Dunn test(α=.05). The flexural strength of the resin post-curing under vacuum was higher than that of the resin post-curing in air. In the comparison according to the post-curing time, in the case of the post-curing equipment without vacuum, the 30 minute curing time showed significantly higher flexural strength than the 10 minute curing time, except for the biaxial flexural strength of CH(P<.05). In the post-curing equipment with vacuum, the three-point flexural strength of all 3D printing resins(DT, CH, and CP) showed a higher value at 30 minute curing time than at 10 minute curing time.

• 원예과학기술지
• /
• 제31권3호
• /
• pp.289-298
• /
• 2013

마의 수확 후 관리기술 최적화 일환으로 3년에 걸쳐 단계적으로 치유 처리 및 저장온도에 따른 품질변화를 분석하였다. 마 괴근은 11월 초 중순에 수확하였고 수확후처리로서 상온과 $29^{\circ}C$ 열풍 조건에 따라 기간을 달리하는 치유과정을 거쳤다. 치유처리 후 저장온도는 저온장해 발생여부 판단과 저장 기간 최적화를 위해 $0.5-7.5^{\circ}C$ 범위에서 검증과정을 거쳤고 저장기간은 4개월에서 7개월까지 점진적으로 연장하였다. 저장 후 유통품질 유지를 위한 처리로는 단시간 $60^{\circ}C$ 열풍처리 후 $20^{\circ}C$ 상온유통과 $7^{\circ}C$ 저온유통 효과를 비교하였다. 수확 후 치유처리는 마의 호흡속도를 감소시켰고 상온치유보다는 3-5일 열풍치유가 장기저장 후 경도를 유지하고 중량감소를 낮춤으로써 품질유지에 보다 효과적이었다. 다양한 저장온도를 설정한 장기 저장 실험결과, $0.5^{\circ}C$에 저장된 마는 유통과정에서 저온장해 현상으로 판단되는 호흡속도의 증가와 조직붕괴 및 연화현상으로 인한 상품성의 저하가 빠르게 진행되었다. 적정 저장온도로는 저온장해 현상을 보이지 않으면서 품질 저하를 최소화하는 $3-4^{\circ}C$ 범위인 것으로 조사되었다. 장기저장 후 유통과정에서는 발근과 부패 억제 등 품질유지를 위해 저온유통이 필요한 것으로 나타났다. 연구결과를 종합해 볼 때, 마는 수확 후 열풍치유와 $3-4^{\circ}C$ 저장 및 저장 후 저온유통 과정으로 구성되는 최적화 프로그램 적용을 통해 7개월 이상 저장 후까지 품질유지가 가능한 것으로 판단되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.214.2-214.2
• /
• 2013

Device performance for the 45 and 32 nm node CMOS technology requires the integration of ultralow-k materials. To lower the dielectric constant for PECVD and spin-on materials, partial replacement of the solid network with air (k=1.01) appears to be more intuitive and direct option. This can be achieved introducting of second "labile" phase during depositoin that is removed during a subsequent UV curing and annealing step. Besides, with shrinking line dimensions the resistivity of barrier films cannot meet the International Technology Roadmap for Semiconductors (ITRS) requirements. To solve this issue self-forming diffusion barriers have drawn attention for great potential technique in meeting all ITRS requirments. In this present work, we report a Cu-V alloy as a materials for the self-forming barrier process. And we investigated diffusion barrier properties of self-formed layer on low-k dielectrics with or without UV curing treatment. Cu alloy films were directly deposited onto low-k dielectrics by co-sputtering, followed by annealing at various temperatures. X-ray diffraction revealed Cu (111), Cu (200) and Cu (220) peaks for both of Cu alloys. The self-formed layers were investigated by transmission electron microscopy. In order to compare barrier properties between V-based interlayer on low-k dielectric with UV curing and interlayer on low-k dielectric without UV curing, thermal stability was measured with various heat treatment temperature. X-ray photoelectron spectroscopy analysis showed that chemical compositions of self-formed layer. The compositions of the V based self-formed barriers after annealing were strongly dominated by the O concentration in the dielectric layers.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.483-490
• /
• 2002

A massive amount of marine clay produced as dredging of coast and sea bed is often dumped in open sea and filled in pond. The treatment of marine clay demand a large area and make fatal environmental problems for echo system. This research work intend to manufacture a light-weight landfill materials which are produced by mixing the dredged marine clay with various amount cement and foam. An extensive Uniaxial and Triaxial compression test are carried out to investigate the strength characteristics of the light-weight cement mixed marine clay with foam under various test conditions. The results indicated that the required unit weight has been achieved with negligible change after 28days curing time in water. It is also recognized that the compressive strength of light-weight landfill materials linearly decrease with increasing initial water content, and the rate of strength decrease with increasing initial water content in water curing was smaller than that of air curing Futhermore, the rate of strength decreased with increasing initial water content, however, the rate become smaller as cement content increased.

• Restorative Dentistry and Endodontics
• /
• 제19권2호
• /
• pp.447-459
• /
• 1994

The purpose of this study is to evaluate of shear bond strength of light-curing composite resin to light-curing glass ionomer cement. Composite resin and glass ionomer cement have been widely used as an esthetic filling materials in dental clinics. To achieve better clinical results, sandwich technic was developed with conpensating for disadvantages of these two materials. Especially, light-curing glass ionomer cement provided greately improved bonding strength of teeth or composite resin, and then excellent clinical results can be acquired. In this study, 6 commercial light-curing glass ionomer cements(3 commercial restorative materials : Fuji II LC, Variglass VLC, Vitremer, and 3 commercial lining materials : Fuji Lining LC, Baseline VLC, Vitrebond) were devided two groups. According to manufacturer's appointment, no surface treatment was referred to N groups. Supposing. of clinical practice, surface grinding with water spray at 320 grit sand paper, 40 seconds etching with 37% phosphoric acid, 20 seconds washing, 20 seconds air drying was referred to N groups. Totally 12 experimental groups were devided, and all 120 specimens from 10 specimens of each groups were made. After light-curing composite resin was bonded to light-curing glass ionomer cement, shear bond strength was tested by Instron universal testing machine between glass ionomer cement and composit resin. The data were analyzed statistically by Student's t-test and ANOVA. The obtained results were as follows; 1. In light-curing glass ionomer cement, restorative materials showed higher shear bond strength to composite resin than lining materials(p<0.05). 2. Variglass VLC of restorative material group and Baseline VLC of lining material group have highest shear bond strength to composite resin(p<0.001). 3. In light-curing glass ionomer cement, surface grinding and acid etching reduced shear bond strength to composite resin(p<0.001)}. 4. VGN group 1s highest shear bond strength to composite resin, VBE group is lowest shear bond strength to composite resin(p<0.001).

• The Journal of Advanced Prosthodontics
• /
• 제5권4호
• /
• pp.423-427
• /
• 2013

PURPOSE. This study evaluated the bond strength between porcelain denture teeth (Bioblend 43D) and four different polymerized denture resins (Lucitone 199, Palapress, Acron MC, Triad) with and without a bonding agent and after four different types of surface treatment (polished, HF etched, sandblasted, air-abraded). MATERIALS AND METHODS. Central incisor porcelain denture teeth were divided into 32 groups of 5 each. Tensile bond strength (MPa) was determined using a testing machine at crosshead speed of 0.5 mm/min. Mean and standard deviation are listed. Data were analyzed by two-way ANOVA. Means were compared by Tukey-Kramer intervals at 0.05 significance level. RESULTS. All surface treatment increased bond strength compared to polished surface and the highest bond strength was found with Palapress resin with etched porcelain surface (8.1 MPa). Bonding agent improved the bond strength of all denture resins to porcelain teeth. Superior bonding was found with Palapress and air-abraded porcelain (39 MPa). CONCLUSION. Resins with different curing methods affect the bond strength of porcelain teeth to denture bases. Superior bonding was found with auto-polymerized resin (Palapress). Application of ceramic primer and bonding agent to porcelain teeth with and without surface treatment will improve the bond strength of all denture resins to porcelain teeth.

• 한국건설순환자원학회논문집
• /
• 제9권3호
• /
• pp.338-347
• /
• 2021

본 논문은 층간 보강재를 보강한 3D 프린팅 콘크리트의 부착강도를 평가하기 위해 수행되었다. 겹침이음 길이에 따라 두 종류의 층간 보강 방법을 고려하였다. 첫 번째 방법은 층간 보강재의 겹침이음을 하지 않았으며, 두 번째 방법은 40mm의 겹침이음을 고려하였다. 또한, 기건양생 조건과 수중양생 조건의 서로 다른 양생 조건을 고려하였다. 실험 변수를 고려하여 3D 프린팅 콘크리트 시편의 압축강도, 쪼갬인장강도 및 휨인장강도를 세가지 하중 방향에서 측정하였다. 압축강도, 쪼갬인장강도 및 휨인장 강도는 하중방향에 영향을 받았다. 특히 3D 프린팅으로 제작한 콘크리트 시편의 층간 부착면에 인장력이 작용하면 쪼갬인장강도 및 휨인장강도가 크게 감소하였다. 그러나 층간 보강재가 보강된 층의 종방향으로 하중이 가해질 때, 프린팅된 시편의 휨인장강도 또는 부착강도는 크게 증가하였다. 또한 기건양생 조건의 휨인장강도 또는 부착강도는 감소하였으며, 기건 양생 조건에 의해 더 많은 공극의 형성을 유발하여 하중에 더 취약해지는 것으로 나타났다.