• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.8
• /
• pp.1153-1161
• /
• 2016

For prevention of moisture adsorption, the fermented red ginseng extract spherical granules were coated by using hydrophobic fractions. The hydrophobic parts were extracted from red ginseng such as the perfect soluble part in 90% ethanol (PSE) and non-soluble part in hot water (NSHW). The optimum operating conditions for making fermented red ginseng extract spherical granules coated with PSE were a feeding rate (FR) of 0.49 mL/min, atomization air pressure (AP) of 2.14 bar, and product temperature (PT) of $48.96^{\circ}C$., whereas conditions for granules coated with NSHW were a FR of 0.61 mL/min, AP of 2.75 bar, and PT of $46.30^{\circ}C$. The solubility of coated fermented red ginseng extract spherical granule was lower than that of not coated. The fermented red ginseng extract spherical granules coated with NSHW showed more preventative effects for moisture adsorption than those coated with PSE, although there were no differences in solubility and fluidity. In the sensory evaluation, granules coated with hydrophobic fractions extracted from red ginseng were shown to be bitterer and less soluble than those not coated spherical granules. In conclusion, fermented red ginseng extract spherical granules coated with hydrophobic extracts from red ginseng showed a preventative effect against moisture.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1511-1519
• /
• 2014

The objective of this paper is to propose a modelling of a small compressed air energy storage system, which drives an induction generator based on a field-oriented control (FOC) principle for a renewable power generation. The proposed system is a hybrid technology of energy storage and electrification, which is developed to use as a small scale of renewable energy power plant. The energy will be transferred from the renewable energy resource to the compressed air energy by reciprocating air compressor to be stored in a pressurized vessel. The energy storage system uses a small compressed air energy storage system, developed as a small unit and installed above ground to avoid site limitation as same as the conventional CAES does. Therefore, it is suitable to be placed at any location. The system is operated in low pressure not more than 15 bar, so, it easy to available component in country and inexpensive. The power generation uses a variable speed induction generator (IG). The relationship of pressure and air flow of the compressed air, which varies continuously during the discharge of compressed air to drive the generator, is considered as a control command. As a result, the generator generates power in wide speed range. Unlike the conventional CAES that used gas turbine, this system does not have any combustion units. Thus, the system does not burn fuel and exhaust pollution. This paper expresses the modelling, thermodynamic analysis simulation and experiment to obtain the characteristic and performance of a new concept of a small compressed air energy storage power plant, which can be helpful in system designing of renewable energy electrification. The system was tested under a range of expansion pressure ratios in order to determine its characteristics and performance. The efficiency of expansion air of 49.34% is calculated, while the efficiency of generator of 60.85% is examined. The overall efficiency of system of approximately 30% is also investigated.

• Culinary science and hospitality research
• /
• v.22 no.8
• /
• pp.149-156
• /
• 2016

The purpose of this study is to reduce the contaminants (total volatile organic compounds (TVOCs), fine particle, odor and total airborne bacteria) during cooking process in cooking chamber, and to decrease the health damage in indoor space that has bad work environment. In order to solve the shortcomings of existing air purifiers and remove all kinds of pollutants effectively, this study focused on the development of indoor air purifiers which are made of bar type. Bio-ceramics filter which combines activated carbon and loess. The air cleaners developed with 4 measuring items including TVOCs, particulate matter, complex odor and total airborne bacteria were measured comparing their pre-service test to their post-service test after a period of time. The measured results showed higher removal efficiency of 91.02% as the concentration of TVOCs was reduced from $2,500{\mu}g/m^3$ to $223{\mu}g/m^3$. Second, the particulate matter removal ratio was 97.51% efficient with average concentration of $26.68{\mu}g/m^3$. Third, the odor showed 95.20% reduction as air dilution ratio averaged out at 144. Last, total airborne bacteria was eliminated by over 94% showing the changeable concentration from $787{\sim}814CFU/m^3$ to $47{\sim}40CFU/m^3$. In addition, the removal rate of harmful pollutants is excellent, and it is expected that the environment of the existing poor cooking room will be greatly improved by using the developed air purifier in combination with the ventilation device and the stove hood.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.32 no.2
• /
• pp.15-25
• /
• 2024

In this study, the regeneration effect of pressurized water and ultrasonic cleaning was investigated for contaminated filter cloth from the sewage sludge filter press process. For this purpose, contaminated filter cloth was collected from a 3-ton sewage sludge hydrothermal carbon treatment filter press. First, the contamination characteristics were analyzed. According to the location of the filter cloth, air permeability and unit mass were measured, and compared with the values of a new filter cloth. Next, the results were mapped over the entire area to evaluate the contamination characteristics. Finally, pressure cleaning at 3 bar and ultrasound at frequencies of 34, 76, 120, and 168 kHz were performed on the contaminated filter cloth. In addition, the cleaning efficiency was evaluated by 3 levels of contamination degree. As a result, pore contamination occurred mainly at the bottom and both sides of the filter cloth, where the filter material was continuously injected and compressed. Surface contamination appeared evenly over the entire area. As a result of washing, air permeability increased by 1.3-3.1%p and contaminant removal was by 2.7-4.4% under pressure. In ultrasonic cleaning, air permeability increased by 12.5-61.5%p and contaminants were removed by 2.7-29.2%. In ultrasonic cleaning the lower the frequency, the higher air permeability and contaminant removal rate. Also, The higher pore contamination level, the better the air permeability improvement and contaminant removal.

• The KSFM Journal of Fluid Machinery
• /
• v.7 no.6 s.27
• /
• pp.28-37
• /
• 2004

An experimental study is conducted to investigate flow characteristics on a small axial-type turbine which is applied as the rotating part of air tools. It operates in a partial admission due to consumption restriction of the high pressure air. In this operating condition, it is necessary to understand flow characteristics for obtaining the high specific output power. Tested turbine consists of two stages and the mean radius of flow passage is less than 10mm. A 6 bar pressure air is used to operate the turbine. The experimental results show that flow angles depend on the measuring location along the circumferential direction, but its discrepancy is alleviated along the axial direction. Absolute flow velocities show three times difference according to the measuring location at the exit of the first rotor due to the partial admission, but they show similar value at the exit of the second rotor by the velocity diffusion. From the measured flow angles and velocities, a ratio of output power obtained by the first and second rotor is estimated. It shows that the output power obtained by the second rotor is about $11\%$ to that by the first rotor at 60,000 RPM. It is effective therefore to improve the first rotor for increasing the turbine output power.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.13 no.4
• /
• pp.196-205
• /
• 2005

In this paper, recent research trend on heat transfer in impinging jet is reviewed. We focused on submerged jet that air issued into air or liquid issued into liquid. To control and enhance the heat transfer in single jet, researchers have performed a lot of experiments by considering the nozzle geometry, impinging surface and active method such as jet vibration, secondary injection and suction flow. The studies on multiple jet have been mainly focused on finding out the optimum condition and on investigating many different factors concerned with application condition (crossflow, rotation and geometry etc.) and combined techniques (rib turbulator, pin fin, dimple and effusion hole etc.). All most experiments showed the detailed heat transfer data by using liquid crystal method, infrared camera technique and naphthalene sublimation method. Many numerical calculations have been performed to investigate the flow and heat transfer characteristics in laminar jet region. Various turbulence models such as $k-\varepsilon-\bar{\nu^2}$, modified $k-\varepsilon-f_{\mu}$ were applied to the calculation for turbulent jet and the predicted results showed a good agreement with the experimental data. Although a lot of studies on impinging jet have performed consistently up to recently, further studies are still required to understand the flow and heat transfer characteristics more accurately, and to give a guideline for optimum impinging jet design in various applications.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.307-308
• /
• 1987

A low-Pressure gap decoupling crow-bar switch was designed and operated to obtain prolonged current pulses by discharging 50kJ condeser banks. And air core Rogowski coil was used for measuring high current.

• Journal of Korean Society of Forest Science
• /
• v.38 no.1
• /
• pp.27-32
• /
• 1978

The diurnal pattern of leaf water potential in cuttings by Dye Method was as follows: 1. Diurnal pattern of leaf water potential (${\psi}_l$) in Viburnum Awabuki K. Koch and Daphne odora Thunb. was shown the pattern of the curves without mutual relation with soil classes when soil water potential (${\psi}_s$) was 0 bar. When ${\psi}_s$ was above -0.01 bar, the cuttings in the loamy sand (L.S.) was shown by the maximum values than that in sandy clay (S.C.) by about -1 bar gap (Fig. 1). 2. The diurnal changes of ${\psi}_l$ was shown the most high from two to eight O'clock in the morning, the maximum value was -3 bars when ${\psi}_s$ was above -0.01 to -0.02 bar, and was -4 bars below -0.03 bar. The diurnal the lowest values of ${\psi}_l$ showed -20 to -22 bars from one to two O'clock in the afternoon. In the fifteenth day after cutting V.A., the staying time in the diurnal maximum values of ${\psi}_l$ is about half in comparison with it in the fifth day. The curves of recovery of water stress (Fig. 1), the former reached to the diurnal maximum values -1 to -2 bars lately every hours comparing with it of the latter. The general diurnal pattern of ${\psi}_l$ was most clearly related to change with air temperature and the relative humitidy. 3. Comparing the treatment block by IAA 50 ppm with controlled block in fifteenth day after V.A. cuttings, in case of treatment reached to maximum values -2 to -3 bars lately as shown Fig. 2., and also staying times was only half in comparison with controlled block. 4. The cuttings 4 leafs was much rootings than 2 leafs in V.A. (Table. 1), and the former reached maximum value -2 to -3 bars lately every hours comparing with the latter. 5. In case of Buxus microphylla var. Koreana as shown Fig. 3., comparing the pattern curves of in the cuttings 8 leafs with 4 leafs, the former reached to maximum values -2 to -3 bars lately in comparison with the latter, but reffering to the amount of rooting (Table. 2), the former is less than the latter.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.4
• /
• pp.878-885
• /
• 2008

The FPDs(Flat Panel Displays) such as LCD(Liquid Crystal Display) and PDP(Plasma Display Panel) and OLED(Organic Light Emitting Diode), recently, have been substituted for CRT(Cathode Ray Tube) displays because they have a convex surface, small volume, light weight and lower electric power consumption. The productivity of FPDs is greatly dependent on the area of thin glass panel with 0.6 - 0.8mm thickness because FPDs are manufactured by cutting a large-scaled thin glass panel with patterns to the required product dimensions. So FPD's industries are trying to increase the area of thin glass panel. For example, the thin glass panel size of the 8th generation is 2,200mm in width, 2,600mm in length and 0.7mm in thickness. The air flows both in the thin glass panel and in the porous PE-plate surface were modeled and analyzed, from which a working condition was estimated. The thin glass panel on the porous PE-plate surface with self-lubricating characteristics was investigated and compared with that on the square duct floating bar surface with many holes of 1mm diameter when the thin glass panel contacts the floating bar surface due to malfunction of electric power supply.

• Journal of the Korea Concrete Institute
• /
• v.13 no.3
• /
• pp.277-284
• /
• 2001

Hardened concrete contains pores of varying types and sizes, and therefore the transport of air through concrete can be considered. The rate of permeability will not only depends on the continuity of pores, but also on the moisture contents in concrete and finishing material on concrete. Also it knows that the durability of reinforced concrete structure is concerned with air permeability which effects on the carbonation occurred by invasion of CO2 gas and the corrosion of steel bar occurred by O$_2$. In this paper, the effects of curing conditions and finishing materials on carbonation and air permeability are investigated according to the accelerated carbonation test. As results, carbonation velocity and air permeability are effected by curing conditions and finishing materials, and air permeability coefficient is effected by moisture content. Also the relationship between carbonation velocity coefficients and air permeability coefficients has been quite well established.