• 한국도로학회논문집
• /
• 제17권3호
• /
• pp.49-58
• /
• 2015

PURPOSES : The use of environmentally friendly construction methods has been recently encouraged to reduce fuel consumption and the effects of global warming. For this purpose, the roller compacted concrete pavement (RCCP) construction method has been developed. RCCP is more environmentally friendly and economically efficient than general concrete by reducing the amount of CO2 generated through the application of a smaller amount of cement. RCCP has a number of advantages such as an easy construction method, low cost, high structural hydration performance, and aggregate interlocking. However, mix design standards and construction guidelines of RCCP are required for domestic application. In addition, a study on aggregate selection, which has an effect on the characteristics of RCCP, is necessary owing to a limited number of researches. Thus, the aggregate effect on the performance of RCCP in securing the required strength and workability was evaluated in consideration of domestic construction. METHODS : Sand and coarse aggregates of both 19mm and 13mm in maximum size were used in this study. Four types of aggregate gradations (s/a = 30%, 58%, and 70% for the sand and coarse aggregate of 19mm in maximum size, and s/a = 50% for a combination of the three types of aggregates) were set up to investigate the effects of the PCA band on the RCC characteristics. The conditions of s/a = 30% and 70% were evaluated to check the gradation effect outside of the recommended band. The conditions of s/a = 58% and 50% were used because they are the optimum combination of the two and three types of aggregates, respectively. RCCP gradation band was suggested gradation with a proper construction method of RCCP by synthetically comparing and analyzing the correlation of optimum water content, maximum dry density, and strength of requirements through its consistency and compaction test. RESULTS : The lower and upper limit lines are insufficient to secure a relatively strong development and workability compared to an aggregate gradation in the RCCP gradation band region. On the other hand, the line in the RCCP gradation band and the 0.45 power curve in the RCCP gradation band region were satisfactory, ensuring the required strength and workability. CONCLUSIONS : The suitable aggregate gradation on RCCP process should meet the RCCP gradation band area; however, fine particles passing through a #60 sieve do not need to be within the recommended gradation band because the influence of this region on such fine particles is small.

• 한국구조물진단유지관리공학회 논문집
• /
• 제28권1호
• /
• pp.24-31
• /
• 2024

기존 대부분의 3D 콘크리트 프린팅 연구는 모르타르를 재료로 활용하고 있다. 다만, 굵은 골재를 포함한 콘크리트에 비해 모르타르를 사용할 경우에는 높은 바인더 함량과 잔골재량으로 인하여 경제성이 저하될 수 밖에 없다. 따라서, 3D 프린팅 기술의 건설산업 적용 확대를 위해서는 굵은 골재를 사용한 콘크리트 3D 프린팅에 대한 연구가 요구된다. 본 연구에서는 굵은 골재가 포함된 3D 프린팅 용 콘크리트의 배합설계 프로세스를 제안하고자 하였다. 다양한 문헌연구 및 배합실험을 참고하여 3D 프린팅에 적합한 배합을 도출하였으며, 출력실험을 통하여 압출성을 검증하였다. 콘크리트 배합의 증점제(Viscosity modifying agent, VMA) 함량을 출력실험의 변수로 설정하였으며, 출력된 필라멘트의 치수 적합성, 골재분포도, 표면 품질을 평가하여 압출성능을 검증하였다. 실험결과, VMA의 함량이 높은 배합이 더 우수한 치수 적합성과 표면 품질을 보였으며, VMA 함량이 다름에도 불구하고 모든 배합에서 골재분포가 균등하게 나타났다. 실험결과를 바탕으로 굵은 골재가 포함된 콘크리트의 압출성을 향상 시킬 수 있는 배합설계 프로세스를 도출하였다.

• 콘크리트학회논문집
• /
• 제14권1호
• /
• pp.67-75
• /
• 2002

콘크리트 구조물의 설계 덴 해석에 있어서나 구조물 처짐 제어에 있어서 가장 중요한 재료적 변수는 탄성계수이다. 일반적으로 탄성계수는 실용적 측면에서 측정이 용이한 단위중량과 압축강도만의 함수로써 간략하게 정의되고 있다. 그러나 이러한 회귀식들은 대부분 실험자료에 대한 평균적인 의미이므로 매우 많은 불확실성이 포함되어 있어 지금까지 제시된 많은 규준식 및 실험식들이 다소의 차이가 있다. Fig. 1에서와 같이 이러한 식들은 압축강도와 탄성계수사이의 큰 상관성이 있음을 잘 나타내고 있으나, 동일한 압축강도에서 탄성계수는 크게 분산된 값으로 측정됨을 알 수 있다. 본 연구에서는 고강도 콘크리트 영역에서 탄성계수에 미치는 배합변수들의 영향을 통계적 기법을 이용하여 분석하고 이를 통하여 동일한 압축강도에서 최대의 탄성계수를 얼기 위한 방안을 구명하였다.

• 한국건축시공학회지
• /
• 제13권5호
• /
• pp.491-497
• /
• 2013

본 연구의 목적은 구조용 경량골재 콘크리트의 배합설계 절차를 확립하고, 설계강도로부터 콘크리트 목표 기건밀도의 범위를 평가하는 것이다. 본 절차를 확립하기 위해, 기존 347 실험데이터의 비선형 회귀분석 및 두 경계조건 (절대용적 및 콘크리트 기건밀도)에 기반한 수학적 모델을 구성하였다. 배합설계 모델제시 결과, 설계강도에 대한 물-시멘트비와 콘크리트 기건밀도는 굵은골재 체적비의 증가와 함께 감소하는데, 이 경향은 모래 경량보다는 전 경량골재 콘크리트에서 현저하였다. 경량골재 콘크리트의 기건단위는 설계강도에 따라 임의의 범위에서 설정되어야 하는데, 이는 제시된 모델에 의해 평가될 수 있다.

• 한국농공학회지
• /
• 제39권2호
• /
• pp.51-56
• /
• 1997

Abstract Over 4.1 billion tons of non-hazardous solid wastes are generated in the United States annually. This equals to about 16 tons of wastes per person, per year. Disposal of the wastes is a national concern due to many factors such as environmental issues, costs, and public views. South Carolina, like many other states, had a home of many military bases which were ordered to be closed. The contaminated soil was vitrified and tested for suitability in the asphalt mixes. For mix design purposes, a total of 75 specimens were made and tested. For moisture susceptibility testing, a total of 32 samples were made and tested. The results indicate that the mixtures made with sample B produced dry and wet that were comparable with the controlled mixture. At this point and with in this limited study, use of 5% of sample B in asphalt mixture is recommended in several applications such as parking lots, walking paths and drive ways.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.81-84
• /
• 2006

Currently, natural aggregates of good quality are hard to use because of continuous decrease of internal aggregate resource and regulation of gathering. So, use of crushed sand was being increased. On the other hand, skyscraper projects with 100 stories are being planned within the country and high strength concrete must be used to construct a skyscraper with 100 stories. High strength concrete is necessary to use crushed sand too because we are still unable to secure natural aggregates of good quality. So, This study indicated basic data necessary for mix design of high strength concrete through valuation of concrete property by quality variation of crushed sand.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.61-68
• /
• 2006

Cemented Sand and Gravel(CSG) is a material made by simple mixing of rock-based raw materials such as excavated soil and riverbed gravel together with cement and water. The use of CSG methodl for cofferdam and large dam is gradually increasing in Japan because a quarry and aggregate plants can be diminished. Also, the CSG method can reduce dam construction cost, construction duration and destruction of environment. In this paper, field test and test construction of CSG method was conducted on Hwabuk Dam. The mechanical properties of CSG, such as compressive strength, extention strength and field permeability test were investigated. From the results of the experimental study, application study of CSG method was discussed.

• 산업기술연구
• /
• 제16권
• /
• pp.45-50
• /
• 1996

An experimental study os performed to examine the feasibility of using wastes steel furnace slag construction materials and its utility as a replacement for the natural resources to prevent the economic loss was investigated. A half factorial exprements was performed with the variables of W/C ratio, S/A, Coarse aggrigate/Slag ratio and slump as a preliminary study for optimum mix design of concrete. The results show that the W/C ratio and Slump ratio are the most important factor to the concrete strength. The substitute of waste Slag up to 100% has little influence, saying that it can substitute the coarse aggregate without damaging the concrete properties.

• 한국농공학회논문집
• /
• 제55권3호
• /
• pp.123-128
• /
• 2013

This study was performed to evaluate the slump flow, air content, setting time, compressive strength, adiabatic temperature rise and diffusion coefficient of chloride used ordinary portland cement, crushed coarse aggregate, crushed sand, river sand, fly ash, limestone powder, blast furnace slag powder and superplasticizer to find optimum mix design of low carbon green concrete for structures. The performances of low carbon green concrete used fly ash, limestone powder and blast furnace slag powder were remarkably improved. This fact is expected to have economical effects in the manufacture of low carbon green concrete for structures. Accordingly, the fly ash, limestone powder and blast furnace slag powder can be used for low carbon green concrete material.

• 한국농공학회지
• /
• 제41권6호
• /
• pp.90-96
• /
• 1999

Over 4.1 billion metric tons of non-hazardous solid wstes are generated in the United States annually. Therefore, there is a need to reuse or reprocess as many products or by-products as possible. In this report, theaggregates produced from Naval Shipyard and Charleston area dredge spoils are designated as GP-21-23 and GP 4-5, repectively. The major objective of this study is to determine the feasiblity of the use of these aggregates in concrete. The followings are some of the conclusions, observations and recommendations regarding this portion of the research project. In most cases, the unit weight of concrete containing GP 21-23 and GP 4-5 (vitrified galss) lower than the control concrete, and the concrete containing vitrified glass produced lower compressive and bending strength compared to the control. However the concrete containing virtrified glass could be used in the field based on the minimum criterial set for the mix design. The use of vitrified glass in concrete is recommended in several applications except parking lots, side walks and main roads, because abrasion resistace is not high.