• 반도체디스플레이기술학회지
• /
• 제18권4호
• /
• pp.100-104
• /
• 2019

The 'ITO/Ag/ITO' multilayers as a highly conductive and transparent electrode, even with the optimum thickness conditions, the transmittances were much lower than those of a single ITO layer on some ranges of the visible wavelength. In order to improve the transmittance, Ag layer was formed with mesh structure. Where, the thickness of the Ag layer was about 10 nm and the space between the Ag lines was varied from 2.9 ㎛ to 19.6 ㎛ with the fixed Ag width of about 1.2 ㎛ in order to vary an open ratio of the Ag mesh structure. The transmittance and sheet resistance in the ITO/Mesh-Ag/ITO multilayer structure were analyzed depending on the open ratio. As a result, a trade off in the open ratio was necessary in order to obtain the transmittance as high as possible and the sheet resistance as possible low. By the open ratio of about 86%, in the ITO/Mesh-Ag/ITO multilayer structure, the transmittance was nearly same as the single ITO layer and the sheet resistance was about 62.3 Ω/.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2001년도 학술대회 논문집
• /
• pp.112-113
• /
• 2001

In this paper, we propose an electrical method which is to estimate Ag ratio to Bi-2223/Ag tape.

• 한국초전도ㆍ저온공학회논문지
• /
• 제1권2호
• /
• pp.43-48
• /
• 1999

The normal zone propagation (NZP) velocity and V-I characteristics of two Bi-2223 pancake coils with different Ag/SC ratio were investigated based on the experimental results and broad resistive transition were obesved in two coils. The measured NZP velocity of coil was found to be faster due to increase of Ag/SC ratio, and agree well with calculated data from two dimensional heat balance equation.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 1999년도 제1회 학술대회논문집(KIASC 1st conference 99)
• /
• pp.109-112
• /
• 1999

The normal zone propagation (NZP) velocity and V-I characteristics of two Bi-2223 pancake coils with different Ag/SC ratio were investigated by experiment. Non-uniformity of Ic and broad restive transition was oberserbed in two coils. The NZP velocity of azimuth direction is faster than radius direction, and the NZP velocity of coil with higher Ag/SC ratio is faster than another coil with lower Ag/SC ratio.

• Journal of Korean Vacuum Science & Technology
• /
• 제6권2호
• /
• pp.79-83
• /
• 2002

As Ag does not form my silicide on Si surfaces, Ag wire is a candidate for self-assembled nanowire on the reconstructed and single-domain Si(5 5 12)-2 $\times$ 1. In the present study, various Ag coverages and post-annealing temperatures had been tested to fabricate a Ag nanowire with high aspect ratio. When Ag coverage was less than 0.03 ML and the post-annealing temperature was 500(C, Ag atoms preferentially adsorbed on the tetramer sites resulting in Ag wires with an inter-row spacing of ~5 nm. However, its aspect ratio is relatively small and its height is also not even. On the other hand, the Ag-posited surface completely loses its reconstruction even with the same annealing at 500 $\^{C}$ if the initial coverage exceeds 0.05 ML. But the additional subsequent annealing at 700$\^{C}$ and slow-cooling process recovers the well-ordered Ag chain with relatively high aspect ratio on the same tetramer sites. It can be understood that, in the double step annealing process, the lower temperature annealing is required for cohesion of adsorbed Ag atoms and the higher temperature annealing is for providing Ag atoms to the tetramer sites.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.256-258
• /
• 2003

Two Si wafers are bonded with indium-silver alloy using diffusion bonding method. When silver and indium thin films are contacted, they diffuse into each other and form inter-metallic compounds like $AgIn_2$, $Ag_2In$, $Ag_3In$ etc. These compounds are determined by ratio of two metals. From phase diagram of Ag-In alloy, we can get the ratio of $Ag_2In$, that has high melting point about 700$^{\circ}C$, approximately 2:1. This ratio was made by controlling of film thickness. And bonding was executed by annealing and adding pressures at a time. The joint of these wafers had been observed by SEM. And we had also seen the EDS (Energy Dispersive Spectroscopy) data to analysis the component of samples.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.527-530
• /
• 2002

A lot of efforts have been focused on the optimization of PIT parameters for Bi-2223/Ag wire. In this paper, initial annealing of Bi-2223/Ag wire to transform Bi-2212 orthorhombic from Bi-2212 tetragonal Precursor was investigated. This initial annealing step at low oxygen partial pressure were to transform Bi-2212 orthorhombic structure and to reduce the formation of second phases at superconducting wire. However Bi-2223 Phases were appeared at higher annealing temperature. Critical currents(Je) of Bi-2223/Ag tapes were sintered at low oxygen Partial pressure were higher than that of the wires sintered at atmosphere condition. In order to investigate the effect of rolling reduction ratio, Bi-2223/Ag HTS tapes were rolled with different reduction ratio. There were no clear difference of Je and filaments shape with various rolling reduction ratio.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.46-49
• /
• 2002

The aim of this paper is to investigate the influence of various deformation ratio on texture of Ag tapes that can be used as a RE-$Ba_2Cu_3O_{7-{\delta}}$ coated conductor tapes without any buffer layer. We fabricated as-rolled Ag substrate with various deformation ratio per step. Thickness and total deformation ratio of Ag tapes were $100{\mu}m$ and >98%, respectively. And as-rolled Ag substrate was annealed at $750^{\circ}C$ for 30min. The as-rolled and recrystallization textures were measured using x-ray pole figures and orientation distribution function (ODF) analysis. With the increase of rolling ratio from 5 to 20%, deformation texture are changed from {1l0}<311> to {1l0}<112>, {032}<100>, {051}<211>. After recrystallization by annealing, main texture was observed to {013}<100> under present condition.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2001년도 추계 기술심포지움
• /
• pp.67-73
• /
• 2001

To investigate the relationships of solder joint characteristics with solder composition and A:V ratio (solder volume per pad area), Sn-37Pb and Sn-4.0Ag-0.5Cu solder balls with 330, 400, 450 and $457{\mu}{\textrm}{m}$ size were reflowed on same substrate. Sn-37Pb and Sn-4.0Ag-0.5Cu was reflowed at $220^{\circ}C$ and $240^{\circ}C$ respectively by IR-type soldering machine. As a result of reflowed solder- ball diameter(D) and height(H) measurement, D/H was decreased with solder ball size increment in range of 330~450 ${\mu}{\textrm}{m}$. But, D/H was increased in the solder joint for 457 ${\mu}{\textrm}{m}$ size, it was caused possibly by decrement of solder ball height increment compared with solder volume increment. As a result of shear and pull test, joint strength with A:V ratio was high. Joint strength of Sn-4.0Ag-0.5Cu was higher than Sn-37Pb. However, Sn-37Pb had more stable solder joint of small standard deviation. A thick and clean scallop type Ni-Cu-Sn intermetallic compound layer was formed in high A:V ratio and Sn-4.0Ag-0.5Cu solder joint interface.

• 한국응용과학기술학회지
• /
• 제31권2호
• /
• pp.313-319
• /
• 2014

This study was performed to obtain high conversion efficiency of $NH_3$ and minimize generation of nitrogen oxides using metal-supported catalyst with Ag : Cu ratio. Through structural analysis of the prepared catalyst with Ag : Cu ratio ((10-x)Ag-xCu ($0{\leq}x{\leq}6$)), it was confirmed that the specific surface area was decrease with increasing metal content. A prepared catalysts showed Type II adsorption isotherms regardless of the ratio Ag : Cu of metal content, and crystalline phase of $Ag_2O$, CuO and $CuAl_2O$ was observed by XRD analysis. In the low temperature($150{\sim}200^{\circ}C$), a conversion efficiency of AC_10 recorded the highest(98%), whereas AC_5 (Ag : Cu = 5 : 5) also showed good conversion efficiency(93.8%). However, in the high temperature range, the amounts of by-products(NO, $NO_2$) formed with AC_5 was lower than that of AC_10. From these results, It is concluded that AC_5 is more environmentally and economically suitable.