• Composites Research
• /
• v.35 no.2
• /
• pp.69-74
• /
• 2022

In this study, the conductive paste used in a wide range such as wiring in the electronic packaging field, the automobile industry, and electronic products is manufactured under various process conditions due to the simplicity of the process, and then the thermal, mechanical, and electrical characteristics are analyzed and simulation studies are conducted to optimize the process. to establish the conditions of the conductive paste manufacturing process. First, a conductive paste was prepared by setting various types of binder resin, an essential component of the conductive paste, and characteristics such as thermal conductivity, tensile strength, and elongation were analyzed. Among the binder resins, the conductive paste applied with a flexible epoxy material had the best physical properties, and a simulation study was conducted based on the physical property data base of the conductive face. As a result of the simulation, the best physical properties were exhibited when the Ag flake volume fraction was 60%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.5
• /
• pp.12-18
• /
• 2008

Ag paste was employed for source and drain electrode of OTFTs and for the data metal lines of OTFT-OLED array on PC(polycarbonate) substrate. We tested two kinds of Ag-pastes such as pastes for 325 mesh and 500 mesh screen mask to examine the pattern ability and electrical performance for OTFTs. The minimum feature size was 60 ${\mu}m$ for 325 mesh screen mask and 40 ${\mu}m$ for 500 mesh screen mask. The conductivity was 60 $m{\Omega}/\square$ for 325 mesh and 133.1 $m{\Omega}/\square$ for 500 mesh. For the OTFT performance the mobility was 0.35 $cm^2/V{\cdot}sec$ and 0.12 $cm^2/V{\cdot}sec$, threshold voltage was -4.7 V and 0.9 V, respectively, and on/off current ratio was ${\sim}10^5$, for both screen masks. We applied the 500 mash Ag paste to OTFT-OLED array because of its good patterning property. The pixel was composed of two OTFTs and one capacitor and one OLED in the area of $2mm{\times}2mm$. The panel successfully worked in active mode operation even though there were a few bad pixels.

• Applied Chemistry for Engineering
• /
• v.29 no.6
• /
• pp.782-788
• /
• 2018

Submicron copper-silver core-shell (Cu@Ag) particles were synthesized using the sonochemical combined transmetallation reaction and the application to printed electronics as a low cost conductive paste was evaluated. $Cu_2O$ of the $Cu_2O/Cu$ composite used as a core in the reaction for the synthesis of core-shell was sonochemically reduced to Cu, and Cu atoms functioned as a reducer for silver ions in transmetallation to achieve the copper-silver core-shell structure. The characterization of submicron particles by TEM-EDS and TG-DSC confirmed the core-shell structure. Conductive pastes in which 70 wt% Cu@Ag was dispersed in solvents were prepared using a binder and wetting agents, and coated on the polyamide film using a screen-printing method. Printed paste films containing synthesized Cu@Ag particles with 8 at% and 16 at% Ag exhibited low resistivity of 96.2 and $38.4{\mu}{\Omega}cm$ after sintering at $180^{\circ}C$ in air, respectively.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.51-56
• /
• 2014

After the preparation of low-cost conductive paste containing Ag-coated Cu flakes, thermal conductivity and electrical resistivity of the paste were measured with different curing conditions. Under air-curing conditions, the thermal conductivity of the cured sample increased with an increase of curing time from 30 to 60 min. After identical curing time of 60 min, the sample cured under nitrogen indicated more enhanced thermal conductivity than that cured under air, approaching that of paste containing pure Ag flakes. Under air-curing conditions, meanwhile, the electrical resistivity of the cured sample increased with an increase of curing time from 30 to 60 min. After identical curing time of 60 min, however, the sample cured under nitrogen indicated extremely enhanced electrical resistivity ($7.59{\times}10^{-5}{\Omega}{\cdot}cm$) in comparison with that cured under air.

• Applied Chemistry for Engineering
• /
• v.32 no.1
• /
• pp.28-34
• /
• 2021

SiO2/Ag core-shell nanoparticles were synthesized by combining modified Stöber process and reverse micelle method using acetoxime as a reducing agent in water/dodecylbenzenesulfonic acid (DDBA)/cyclohexane reverse micells. The SiO2/Ag core-shells were studied for structure, morphology and size using UV-visible spectroscopy, XRD, SEM and TEM. The size of a SiO2/Ag core-shell could be controlled by changing the [water]/[DDBA] molar ratio (WR) values. The size and the polydispersity of SiO2/Ag core-shells increased with increase of the WR value. The resultant Ag nanoparticles exhibit a strong surface plasmon resonance (SPR) peak at 430 nm over the amorphous SiO2 nanoparticles. The SPR peak shifted to the red side with increase in nanoparticle size. Conductive pastes with 70 wt% SiO2/Ag core-shell were prepared, and the pastes were coated on the PET films using a screen-printing method. The printed paste film of the SiO2/Ag core-shell showed higher surface resistance than the commercial Ag paste in the range of 460~750 µΩ/sq.

• Applied Chemistry for Engineering
• /
• v.34 no.1
• /
• pp.36-44
• /
• 2023

Core-shell TiO₂/Ag nanoparticles were synthesized by a modified sol-gel process and the reverse micelle method using acetoxime as a reducing agent in water/dodecylbenzenesulfonic acid (DDBA)/cyclohexane. The structure, shape, and size of the TiO₂/Ag nanoparticles were investigated using X-ray diffraction (XRD), UV-visible spectroscopy, scanning electron microscope (SEM), transmission electron microscope (TEM), and thermogravimetric analysis (TGA). The size of TiO₂/Ag nanoparticles could be controlled by changing the [water]/[DDBA] molar ratio values. The size and the polydispersity of TiO₂/Ag nanoparticles increased when the [water]/[DDBA] molar ratio rose. The resultant Ag nanoparticles over the anatase crystal TiO₂ nanoparticles exhibited a strong surface plasmon resonance (SPR) peak at about 430 nm. The SPR peak shifted to the red side with the increase in nanoparticle size. Conductive pastes with 70 wt% TiO₂/Ag nanoparticles were prepared, and the pastes were coated on the PET films using a screen-printing method. The printed paste films of the TiO₂/Ag nanoparticles demonstrated greater surface resistance than conventional Ag paste in the range of 405~630 μΩ/sq.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.4
• /
• pp.47-52
• /
• 2003

A new type of Bi based glass frit was developed for Ag paste in PDP applications and its properties are compared with the commercially used Pb based glass frit. After optimization of the properties of Bi based frits for PDP application such as the softening temperature and the coefficient of thermal expansion (C.T.E), the screen printed electrodes prepared with the Bi based fit contained Ag paste were characterized. In $Bi_2O_3-B_2O_3-Al_2O_3$ glass system with the more than 50% of $Bi_2O_3$, the softening temperature, the thermal expansion coefficient and the line resistivity was 400∼$480^{\circ}C$, 7.31∼$10.02\times 10^{-6}/^{\circ}C$> and 4.1∼4.8$\Omega$ respectively. Properties of the Bi based frits are comparable with the Pb based frits. A printability and an uniformity of the Bi based frits were excellent in screen printed Ag eletrode. The Bi based frit system is an excellent candidate material for Pb free and Alkali free frit in PDP applications.

• Journal of the Korean Ceramic Society
• /
• v.41 no.4
• /
• pp.313-322
• /
• 2004

Thick film photolithography is a new technology in that the lithography process such as exposure and development is applied to the conventional thick film process including screen-printing. In this research, low-temperature cofireable silver paste, which enabled the formation of thick film fine-line using photolithographic technology, was developed. The optimum composition for fine-line forming was studied by adjusting the amounts of silver powder, polymer and monomer, and the additional amount of photoinitiator, and then the effect of processing parameter such as exposing dose on the formation of fine-line was also tested. As the result, it was found that the ratio of polymer to monomer, silver powder loading, and the amount of photoinitiator were the main factors affecting the resolution of fine-line. The developed photosensitive silver paste was printed on low-temperature cofireable green sheet, then dried, exposed, developed in aqueous process, laminated, and fired. Results showed that the thick film fine-line under 20$\mu\textrm{m}$ width could be obtained after cofiring.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.1
• /
• pp.67-73
• /
• 2012

After flash memory card(FMC) was manufactured by $B^2it$ process, interfacial reaction of silver bump with thermal stress was studied. To investigate bonding reliability of Ag bump, thermal shock and thermal stress tests were conducted and then examined on the crack between Cu land and Ag bump interface. Diffusion reaction of Ag bump/Cu land interface was analyzed using SEM, EDS and FIB. The Ag-Cu alloy layer due to the interfacial reaction was formed at the Ag/Cu interface. As the diffusivity of Ag ${\rightarrow}$ Cu is faster than Cu ${\rightarrow}$ Ag, a lot of (Cu, Ag) alloy layers were observed at the Cu layer than Ag. These alloy layers contributed to increase the Cu-Ag bonding strength and its reliability.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.82-82
• /
• 2010

표면실장 공법을 통해 CSP 패키지를 보드에 실장 하는데 있어 무연솔더 접합부의 신뢰성에 영향을 미치는 인자 중 가장 중요한 것은 접합부에 형성되는 IMC (Intermetallic compound, 금속간화합물)인 것으로 알려져 있다. 접합부의 칩 부분에는 솔더와 칩의 UBM (Under bump metalization)이 접합하여 IMC가 형성되나, 보드 부분에는 솔더와 보드의 UBM 뿐만 아니라 그 사이에 솔더 페이스트가 함께 접합되어 IMC가 형성된다. 본 연구에서는 패키지의 신뢰성 연구를 위해 솔더 페이스트의 유무 및 두께에 따른 무연 솔더 접합부의 미세조직의 변화를 분석하였다. 본 실험에서는 Sn-3.0(Wt.%)Ag-0.5Cu 조성과 본 연구진에 의해 개발된 Sn-Ag-Cu-In 조성의 직경 $450{\mu}m$ 솔더 볼을 사용하였으며, 솔더 페이스트는 상용 Sn-3.0Ag-0.5Cu (ALPHA OM-325)를 사용하였다. 칩은 ENIG (Electroless nickel immersion gold) finish pad가 형성된 CSP (Chip scale package)를, 보드는 OSP (Organic solderability preservative)/Cu finish pad가 형성된 것을 사용하였다. 실험 방법은 보드를 솔더 페이스트 없이 플라즈마 처리 한 것, 솔더 페이스트를 $30{\mu}m$ 두께로 인쇄한 것, $120{\mu}m$의 두께로 인쇄한 것, 이렇게 3가지 조건으로 준비한 후, 솔더 볼이 bumping된 칩을 mounting하여, $242^{\circ}C$의 peak 온도 조건의 oven(1809UL, Heller)에서 reflow를 실시하여 패키지를 형성하였다. 이후 시편은 정밀 연마한 후, OM(Optical Microscopic)과 SEM(scanning electron microscope) 및 EDS(energy dispersive spectroscope)를 사용하여 솔더 접합부 IMC의 미세조직을 관찰, 분석하였다.