• International Journal of Aeronautical and Space Sciences
• /
• v.15 no.3
• /
• pp.219-231
• /
• 2014

We develop a preliminary design optimization procedure in this paper regarding the wing planform in a solar-powered high-altitude long-endurance unmanned aerial vehicle. A high-aspect-ratio wing has been widely adopted in this type of a vehicle, due to both the high lift-to-drag ratio and lightweight design. In the preliminary design, its characteristics need to be addressed correctly, and analyzed in an appropriate manner. In this paper, we use the three-dimensional Euler equation to analyze the wing aerodynamics. We also use an advanced structural modeling approach based on a geometrically exact one-dimensional beam analysis. Regarding the structural integrity of the wing, we determine detailed configuration parameters, specifically the taper ratio and the span length. Next, we conduct a multi-objective optimization scheme based on the response surface method, using the present baseline configuration. We consider the structural integrity as one of the constraints. We reduce the wing weight by approximately 25.3 % from that in the baseline configuration, and also decrease the power required approximately 3.4 %. We confirm that the optimized wing has sufficient flutter margin and improved static longitudinal/directional stability characteristics, as compared to those of the baseline configuration.

• Journal of Mechanical Science and Technology
• /
• v.20 no.8
• /
• pp.1139-1148
• /
• 2006

This paper addresses the analytical modeling and dynamic response of the advanced composite rotating blade modeled as thin-walled beams and incorporating viscoelastic material. The blade model incorporates non-classical features such as anisotropy, transverse shear, rotary inertia and includes the centrifugal and coriolis force fields. The dual technology including structural tailoring and passive damping technology is implemented in order to enhance the vibrational characteristics of the blade. Whereas structural tailoring methodology uses the directionality properties of advanced composite materials, the passive material technology exploits the damping capabilities of viscoelastic material (VEM) embedded into the host structure. The VEM layer damping treatment is modeled by using the Golla-Hughes-McTavish (GHM) method, which is employed to account for the frequency-dependent characteristics of the VEM. The case of VEM spread over the entire span of the structure is considered. The displayed numerical results provide a comprehensive picture of the synergistic implications of both techniques, namely, the tailoring and damping technology on the dynamic response of a rotating thin-walled b ε am exposed to external time-dependent excitations.

• Earthquakes and Structures
• /
• v.19 no.2
• /
• pp.91-101
• /
• 2020

This work presents an efficient and original hyperbolic shear deformation theory for the bending and dynamic behavior of functionally graded (FG) beams resting on Winkler - Pasternak foundations. The theory accounts for hyperbolic distribution of the transverse shear strains and satisfies the zero traction boundary conditions on the surfaces of the beam without using shear correction factors. Based on the present theory, the equations of motion are derived from Hamilton's principle. Navier type analytical solutions are obtained for the bending and vibration problems. The accuracy of the present solutions is verified by comparing the obtained results with the existing solutions. It can be concluded that the present theory is not only accurate but also simple in predicting the bending and vibration behavior of functionally graded beams.

• Magazine of the Korea Concrete Institute
• /
• v.10 no.6
• /
• pp.269-280
• /
• 1998

Recently, application of composite materials such as fiber reinforced concretes(FRCs) and fiber reinforced plastics(FRPs) in conjunction with conventional structural components has become one of the main research areas. A proper use of advanced composite materials requires understanding their resistance mechanism and failure mode when they are applied to structures or their components. Particular considerations are given in this research to develop an analytical model which can predict the nonlinear flexural responses of bonded and unbonded prestressed concrete beams possibly having layers of different cementitious composite matrices in a section and/or FRP tendons. The block concept is used, which can be regarded as an intermediate modeling method between the couple method with one block and the layered method with multiply sliced layers in a section. In order to find a particular deflection point of a beam under load, solutions to the 2N-variables are found numerically by using approximate N-force equilibrium equations and N-moment equilibirum equations. The model is shown to successfully predict the flexual behavior of variously reinforced bonded and unbonded prestressed concrete beams. The model is also successful in simulating a gradually increasing load after sudden drop inload resistance due to fracture of one or more FRP tendons. This feature is useful in tracing the overall load-deflection response of a beam prestressed with brittle FRP tendons.

• Wind and Structures
• /
• v.27 no.4
• /
• pp.269-282
• /
• 2018

In this paper, a new displacement field based on quasi-3D hybrid-type higher order shear deformation theory is developed to analyze the static and dynamic response of exponential (E), power-law (P) and sigmoïd (S) functionally graded beams. Novelty of this theory is that involve just three unknowns with including stretching effect, as opposed to four or even greater numbers in other shear and normal deformation theories. It also accounts for a parabolic distribution of the transverse shear stresses across the thickness, and satisfies the zero traction boundary conditions at beams surfaces without introducing a shear correction factor. The beam governing equations and boundary conditions are determined by employing the Hamilton's principle. Navier-type analytical solutions of bending and free vibration analysis are provided for simply supported beams subjected to uniform distribution loads. The effect of the sigmoid, exponent and power-law volume fraction, the thickness stretching and the material length scale parameter on the deflection, stresses and natural frequencies are discussed in tabular and graphical forms. The obtained results are compared with previously published results to verify the performance of this theory. It was clearly shown that this theory is not only accurate and efficient but almost comparable to other higher order shear deformation theories that contain more number of unknowns.

• Advances in Computational Design
• /
• v.1 no.1
• /
• pp.105-117
• /
• 2016

The objective of this work is to study the restraining effect in fire resistance of framed structures and to evaluate the global response of reinforced concrete frames when exposed to fire based on advanced finite element method. To study the response a single portal frame is analyzed. The effect of floor slab on this frame is studied by modeling a beam-column-slab assembly. The evolution of temperature distribution, internal stresses and deformations of the frame subjected to ISO 834 standard fire curve for both the frames are studied. The thermal and structural responses are evaluated and a comparison of results of individual members and entire structure is done. From the study it can be seen that restraining forces has significant influence on both stresses and deflection and overall response of the structure when compared to individual structural member. Among the various structural elements, columns are the critical members in fire and failure of column causes the failure of entire structure. The fire rating of various structural elements of the frame is determined by various failure criteria and is compared with IS456 2000 tabulated fire rating.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.1
• /
• pp.61-67
• /
• 2015

The concept of horizontal shear connection utilization on wood-concrete beams intends to be an alternative connection detail for composite wood-concrete decks. The volume of sawn-wood is over three times more expensive than concrete, in Brazil. In order to be competitive in the Brazilian market we need a composite deck with the least amount of wood and a simple and inexpensive connection detail. This research project uses medium to high density tropical hardwoods managed from the Brazilian Amazon region and construction steel rods. The beams studied are composed of a bottom layer of staggered wood boards and a top layer of concrete. The wood members are laterally nailed together to form a wide beam, and horizontal rebar connectors are installed before the concrete layer is applied on top. Two sets of wood-concrete layered beams with horizontal rebar connectors (6 and 8) were tested in third-point loading flexural bending. The initial results reveal medium composite efficiency for the beams tested. An improvement on the previously conceived connection detail (set with six connectors) for the composite wood-concrete structural floor system was achieved by the set with eight connectors. The new layout of the horizontal rebar connectors added higher composite efficiency for the beams tested. Further analysis with advanced rigorous numerical Finite Element Modeling is suggested to optimize the connection parameters. Composite wood-concrete decks can attend a large demand for pedestrian bridges, as well as residential and commercial slabs in the Brazilian Amazon.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.22 no.2
• /
• pp.117-136
• /
• 2020

The purpose of this study is to analyze changes in high-tech fashion along with the types and characteristics of high-tech fashion that have appeared recently providing diverse material for the fashion field. High-tech fashion requires such research to learn how much distance one has in one's life. It is also meaningful to predict what direction high-tech fashion research may be needed. For research methods, previous research and literary studies were considered and photographs in which high-tech techniques were used were collected using the keyword 'high-tech fashion'. High-tech fashion types can be organized into the four types of luminescent types, mutual interaction types, 3D printing fashion, and virtual fashion. The research results were as follows. First, luminescent fashion was an important expression method of high-tech fashion. Materials for luminescent fashion first started with LED electric wire connections and many methods have been attempted with the appearance of electrically conductive clothing material, such as luminescent lasers and beam projectors. Second, interactive high-tech fashion often appears as variable fashion. The work of Hussein Chalayan, which was combined with advanced technology, set up a base for variable type interactive high-tech fashion in the 2000s. As bioengineering technology has developed, fashion that interacts with the environment without an energy source has appeared and the interaction among fashion, people, and the environment can be seen. Third, diverse forms of expressiveness in virtual reality such as 3D CLO shows a great difference with past high-tech fashion. Simple and diverse attempts made through virtual fittings reduce the limitations of time and space, permit interaction, and add a sense of reality through speed and dynamic physical beauty. Fourth, 3D printed fashion expresses complex and detailed clothing material that is different from those before with the development of computer 3D modeling technology. Modeling that can imitate geometric and bio-engineered structures is possible and mysterious feelings are passed on to people through creative expressions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.5
• /
• pp.819-827
• /
• 1997

In this paper, a new modeling of a fine actuator for an optical pick-up has been proposed and multiobjective optimization of the actuator has been performed. The fine actuator is constituted of the bobbin which is supported by wire suspension, the coils which wind around the bobbin, and the magnets which cause the magnetic flux. If current flows in the coils, magnetic force is so produced as to be balanced with spring force of wire, so the bobbin is pisitioned. In this model the transfer function from input voltage to output displacementof bobbin has been obtained so that we can describe this integrated system with electromagnetic and mechanical parts. Wire suspension is regarded as a continuous Euler beam, damper as distributed viscous damping, and bobbin as a rigid body which can move up- and down- ward motion only. According to the model, the high frequency dynamic characteristics of the fine actuator can be known and the effect of damping can be investigated while the conventional second order model cannot. In multiobjective optimization, two objective functions have been chosen to maximize the fundamental frequency and the sensitivity with respect to the input voltage of the actuator so that Pareto's optimal solutions have been obtained using .epsilon.-constraint method. These objective functions will satisfy the trends which will enhance the access speed and reduce the tracking error in the optical pick-up technology of next generation. In the result of optimization, we obtain the designs of the optical pick-up fine actuator which has high speed, high sensitivity and low resonant peak. Furthermore, we offer the relation between two object functions so that the designer can make easy choice.

• Journal of the Korea Furniture Society
• /
• v.20 no.5
• /
• pp.467-479
• /
• 2009

The high-tech computer technology developments have greatly affected the area of design education. Starting from the mid 80s, innovations in visual presentation methods have heightened with 2D computer graphic programs, CAD & 3D modeling, and Rapid Prototype that allows dimensional generation. The specialty and quality in design studio education have advanced due to the development in presentation methods such as Power Point and Keynote. But there are many problems with the current method of presenting the visual outcome in a data format using beam projectors, which is a vertical presenting method compared to the old studio study method of conducting discussions and reviews based on the substantial outcome. The essence of studio study that allows for comparisons and analysis by horizontally opening up the various work outcomes is being offset. Also the requirement for manual idea sketching work that plays an important role in the initial design phase continuing to decrease due to the digital working process dependence and cumbersome procedures in the presentation. In order to resolve this problem, the CALM system (Class Applied LCD Modular System) has been developed that replaces the method of attaching the sketches or renderings on the wall with a digital multi-display system. In a nutshell, individuals will upload the outcomes online and display them on the CALM system studio that is composed of 32 LCD (Columns: 4 $\times$ Rows: 8) monitors that are 19 inches in size so that various personnel can openly study the design outcomes. Also the central 42 inch PDP monitor that offers touch pad capability allows each design outcome to be described and examined by expanding. The concept phase of this development process has elevated to the production of an operating prototype that is being reviewed of its practicality. It is considered that the development of this system will decrease the extreme tendency of depending on digital operation but achieve revitalization of a more realistic and opened studio study environment compared to the individual consulting method of the old study approach.