• Journal of the Korean GEO-environmental Society
• /
• v.8 no.4
• /
• pp.19-25
• /
• 2007

Process analysis with ASM3 (Activated Sludge Model3) was performed to offer basic data for the optimization of aerated biofilter (ABF) process design and operation. This study was focused on the simulation of the nitrification reaction in ABF which was a part of the advanced nutrient treatment process using bio-adsorption. The ABF process has been developed for the removal of suspended solids and nitrification reaction in sewage. A GPS-X (General Purpose Simualtor-X) was used for the sensitivity analysis and operation assessment. Sensitivity of ASM3 parameters on ABF was analysed and 4 major parameters ($Y_A$, $k_{sto}$, ${\mu}_A$, $K_{A,HN}$) were determined by dynamic simulation using 70 days data from pilot plant operation. The optimized values were 0.14 for $Y_A$, 3.5/d for $k_{sto}$, 2.7/d for ${\mu}_A$ and 1.1 mg/L for $K_{A,HN}$, respectively. Simulation with optimized parameter values were conducted and TN, $NH_4{^+}-N$ and $NO_3{^-}-N$ concentrations were estimated and compared with measured data at the range of 10 min to 4 hrs of hydraulic retention time (HRT). The simulated results showed that optimized parameter values could represent the characteristics of ABF process. Especially, the ABF showed relatively high nitrification rate (60%) under very short HRT of 10 min. As a consequence, the ABF was thought to be successfully used in the site which having high variation of influent loading rate.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.2
• /
• pp.39-46
• /
• 2008

Due to the growth in industrialization, potential hazards in subsurface environments are becoming increasingly significant. The extraction of the contaminant from the soil and movement of the water are restricted due to the low permeability and adsorption characteristics of the reclaimed soils. There are a number of approaches to in-situ remediation that are used in contaminated sites for removing contaminants. These include soil flushing, dual phase extraction, and soil vapor extraction. Among these techniques, soil flushing was the focus of the investigation in this paper. Incorporated technique with PVDs has been used for dewatering from fine-grained soils for the purpose of ground improvement by means of prefabricated vertical drain systems. The laboratory model tests were performed by using the flushing tracer solutions for silty soils and recorded the tracer concentration changes with the elapsed time and flow rates. The modeling was intended to predict the effectiveness and time dependence of the remediation process. Modeling has been performed on the extraction, considering tracer concentration and laboratory model test characteristics. The computer model used herein are SEEP/W and CTRAN/W, this 2-D finite element program allows for modeling to determine hydraulic head and pore water pressure distribution, efficiency of remediation for the subsurface environment. It is concluded that the coefficient of permeability of contaminated soil is related with vertical velocity and extracted flow rate. The vertical velocity and extracted flow rate have an effect on dispersivity and finally are played an important role in-situ soil remediation.

• Polymer(Korea)
• /
• v.34 no.4
• /
• pp.300-305
• /
• 2010

Zaltoprofen is a propionic acid derivative of non-steroidal anti-inflammatory drugs (NSAIDs) and has been widely used in the treatment of a number of arthritic conditions or lumbago. Zaltoprofen has low water solubility and low bioavailability, therefore great efforts have been devoted to enhance the extent of drug adsorption. In this study, zaltoprofen was formulated into a tablet to enhance the bioavailability and to achieve sustained-release using additives such as lactose monohydrate, carboxymethylcellulose (CMC), hydroxypropylmethylcellulose (HPMC). Fourier transform-infrared (FTIR) and differential scanning calorimeter (DSC) were employed to study the structure and crystallization of zaltoprofen in the tablet with various contents of additives. It was found that additives had interactions with zaltoprofen and inhibited the crystallization of zaltoprofen. Tablets containing low viscosity HPMC showed a higher release than those containing high viscosity HPMC. Also, as the amount of CMC increased zaltoprofen release increased.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.408-414
• /
• 2021

This study aimed to improve the production of bioactive materials with antioxidant activity using a fermented Luffa aegyripia extract and improve the anticancer effect by enhancing UV absorption and inhibiting melanoma cell growth. The total phenolic content (TPC) and antioxidant activity of the fermented extract were 30.23 mg GAE/g DM and 45.12%, respectively, which was 1.4 times higher than that of the hot-water extract (HWE). The fermented extract showed a UV adsorption rate of 53.9%, which was 1.5 times higher than HWE, and it was concluded that UV absorption was increased by TPC, which was increased through the fermentation of L. aegyptiaca extracts using Lactobacillus. In the anticancer effect test, fermented and HWE extracts had carcinogenic effects of 1.0 and 2.0 mg/mL, respectively. This suggests that the increased antioxidant activity due to the increase in TPC caused by fermentation contributed to the anticancer effect. The UV absorption rate of fermented extracts was 2.4 times higher than HWE, giving them potential use as cosmetics and pharmaceutical materials with high polyphenol contents and antioxidant properties and skin cancer prevention.

• Applied Chemistry for Engineering
• /
• v.32 no.1
• /
• pp.83-90
• /
• 2021

In this study, effects of the physical and chemical properties of low temperature heated carbon on electrochemical behavior as a secondary battery anode material were investigated. A heat treatment at 600 ℃ was performed for coking of petroleum based pitch, and the manufactured coke was heat treated with different heat temperatures at 700~1,500 ℃ to prepare low temperature heated anode materials. The physical and chemical properties of carbon anode materials were studied through nitrogen adsorption and desorption, X-ray diffraction (XRD), Raman spectroscopy, elemental analysis. Also the anode properties of low temperature heated carbon were considered through electrochemical properties such as capacity, initial Coulomb efficiency (ICE), rate capability, and cycle performance. The crystal structure of low temperature (≤ 1500 ℃) heated carbon was improved by increasing the crystal size and true density, while the specific surface area decreased. Electrochemical properties of the anode material were changed with respect to the physical and chemical properties of low temperature heated carbon. The capacity and cycle performance were most affected by H/C atomic ratio. Also, the ICE was influenced by the specific surface area, whereas the rate performance was most affected by true density.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.620-629
• /
• 2022

By varying various experimental conditions such as heating rate, molar hourly space velocity (MHSV), and nitridation reaction temperature, vanadium oxynitride was prepared through temperature programmed reduction/nitridation reaction (TPRN) of vanadium pentoxide and ammonia, and characterization were performed. In order to investigate the physico-chemical properties of the prepared catalyst, N₂ adsorption-desorption analysis, X-ray diffraction analysis (XRD), hydrogen temperature programmed reduction (H₂-TPR), temperature programmed oxidation (TPO), ammonia temperature programmed desorption (NH₃-TPD), transmission electron microscopy (TEM) was performed. Transformation of V₂O₅ with 5 m² g^-1 low specific surface area by reduction at 340 ℃ to V₂O₃ showed a high specific surface area value of 115 m² g^-1 by micropore formation. As the nitridation temperature increased beyond that, the specific surface area continued to decrease due to sintering. The nitridation reaction variable that had the greatest influence on the specific surface area was the reaction temperature, and the x + y value of VN_xO_y of a single phase approached from 1.5 to 1.0 as the nitridation reaction temperature increased. At a high reaction temperature of 680 ℃, the cubic lattice constant a was VN. close to the value. At 680 ℃, the highest nitridation temperature among the experimental conditions, the ammonia conversion rate was 93%, and no deactivation was observed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1A
• /
• pp.75-84
• /
• 2009

The present study assesses the chloride threshold level for corrosion of steel in concrete by examining the properties of four different binders used for blended concrete in terms of chloride binding, buffering of cement matrix to a pH fall and the corrosion behaviour. As binders, ordinary Portland cement (OPC), 30% pulverised fuel ash (PFA), 60% ground granulated blast furnace slag (GGBS) and 10% silica fume (SF) were used in a concrete mix. Testing for chloride binding was carried out using the water extraction method, the buffering of cement matrix was assessed by measuring the resistance to an artificial acidification of nitric acid, and the corrosion rate of steel in mortar with chlorides in cast was measured at 28 days using an anodic polarisation technique. Results show that the chloride binding capacity was much affected by $C_{3}A$ content and physical adsorption, and its order was 60% GGBS>30% PFA>OPC>10% SF. The buffering of cement matrix to a pH fall was varied with binder type and given values of the pH. From the result of corrosion test, it was found that the chloride threshold ranged 1.03, 0.65, 0.45 and 0.98% by weight of cement for OPC, 30% PFA, 60% GGBS and 10% SF respectively, assuming that corrosion starts at the corrosion rate of $0.1-0.2{\mu}A/cm^{2}$. The mole ratio of [$Cl^{-}$]:[$H^{+}$], as a new presentation of the chloride threshold, indicated the value of 0.008-0.009, irrespective of binder, which would be indicative of the inhibitive characteristic of binder.

• Journal of the Korean Wood Science and Technology
• /
• v.6 no.2
• /
• pp.3-19
• /
• 1978

Five species, Abies koreana Wilson (A. koreana), Castanopsis cuspidata var. Sieboldii Nakai (C. Cuspidata). Machilus thunbergii Sieb. et Zucc. (M. thunbergii), Styrax japonica (S. japonica), and Quercus acuta Thunberg(Q. acuta) growing in the southern part of Korea were selected for the investigation of wood properties. In order to evaluate the wood properties of these five species, anatomical, physical, mechanical, chemical and pulping characteristics were investigated. And this study also covered wood technological problems related to the drying, gluing, debarking, flooring, and wood workability so that these species might serve to the best advantage. The results obtained were summarized as follows: 1. The trunk of A. koreana with many knots was straight. However, the trunks of S. japonica and C. cuspidata were crooked. 2. A. koreana showed the longest and the widest ill the fiber morphology; 2.97mm in length, 39.3${\mu}$ in width. In general, fiber width of all the species investigated were greater than those of other Korean hardwoods. 3. The specific gravity of Q. acuta was 0.74${\pm}$0.03, and that of A.koreana was 0.34${\pm}$0.02. The range of specific gravity of the other species was 0.47-0.52. 4. The adsorption of water was propotioned inversely with the specific gravity, but the adsorption of humidity was proportioned with the specific gravity. In spite of their medium density, S. japonica showed the greatest adsorption, and M. thunbergii the least. The water adsorption of cross section was twice greater than that of lateral direction, and there was a slight difference in between the radial and the tangential direction. 5. Shrinkage for tested five species was ranged from 5.36 to 10.24% in tangential direction, and 2.83~6.13% in radial direction. Q. acuta recorded the greatest shrinkage rate, and A. koreana the least. The greater was the specific gravity, the larger was the shrinkage rate. 6. The mechanical properties of Q. acuta were similar to those of Quercus mongolica which grow in Kangwon-Do. Strength properties of C. cuspidata, M. thunbergii, A. koreana were equivalent to those of other Korean commercial woods with similar specific gravity, except S. japonica which showed slightly higher strength than that of other species with similar density. 7. Higher glue joint strength for urea and phenol adhesieves was recorded in the species of M. thunbergii and C. cuspidata, however, high-density species(Q. acuta) and even low-density species(A. koreana) did not show good joint strength. 8. The attractive figure of M. thunbergii in texture seemed to he appreciated for decoration. And the grain and texture of other species were proper for furniture and building materials. 9. All of the species except Q. acuta were considered good for wood workability. 10. The denser the specific gravity was, the longer the drying time took. However, severe drying defects were formed in M. thunbergii whose density was medium. 11. All the species were considered suitable for the flooring wood expect A. koreana whose density was light. 12. Pentosan component in all the species was great, and the amount of extractives in Q. acuta was worth noticing. 13. Yield in kraft pulp was above the level of economic pulp yield, i.e. 45% in all species. 14. Debarking was easy in the species of A. koreana and M. thunbergii, and debarking after being boiled in water was the most efficient in all species.

• Applied Biological Chemistry
• /
• v.21 no.2
• /
• pp.71-80
• /
• 1978

In an attempt to elucidate the fate of 3,4-DCA and TCAB in various French soils, uniformly $^{14}C-ring-labeled$ 3,4-DCA and TCAB mere utilized and the following results obtained. 1) The rate of breakdown of $^{14}C-3,4-DCA$ into $^{14}CO_2$ was relatively higher in the early stage than that in the later stage. In 6 months of incubation in alkaline soil (pH 7.9), the rate was as high as 6.5% at dose 1 (1.5 ppm) and as low as 1.92% at dose 2(94 ppm), whereas in organic acid soil (pH 5.5) the rate was 4.91% at dose 1 and 4.24% at dose 2, respectively, without making any great difference between the two levels. 2) At dose 1, 47.70% of the initial radioactivity of $^{14}C-3,4-DCA$ was bound to soil in organic acid soil and 29.49% bound in alkaline soil, whereas at dose 2, 38.40% in organic acid soil and 20.30% in alkaline soil, respectively. 3) The amount of formation of $^{14}C-TCAB$ from $^{14}C-3,4-DCA$ seems to depend largely on the concentration of 3,4-DCA applied rather than on soil types. At dose 2, the amount was 50% of the total radioactivity extracted in organic acid soil and 30% in alkaline soil, corresponding to 1.8% and 1.4% of the initial radioactivity applied to soil, respectively. Cis-TCAB also seemed to be formed at dose 2 in both soils. Meanwhile, at dose 1, even though $^{14}C-TCAB$ was detected in trace on tlc and glc in both soils, the amount does not exceed 2 to 3% of the radioactivity extracted, corresponding to 0.05 to 0.1% of the initial radioactivity. 4) The rate of breakdown of $^{14}C-TCAB$ into $^{14}CO_2$ ranged from 0.05 to 0.20% in all the four soils. Most of the applied $^{14}C-TCAB$ remained intact after 3 months, not producing any detectable metabolites. 5) The fact that much more $^{14}C-TCAB$ was adsorbed to alkaline soil than to the other soils strongly indicates that in alkaline condition trans-isomer was converted tocisisomer which has the higher adsorption affinity than the former.

• Korean Journal of Environmental Agriculture
• /
• v.27 no.3
• /
• pp.225-230
• /
• 2008

Objective of this study was to access the environmental impacts of the use of discharge water from municipal waste water treatment plant as alternative irrigation resources during drought season for rice cultivation. For the field experiments, it was observed that plant growth and yield characteristics at 20 days of alternative irrigation period with application of FAST (fertilizer application based on soil test) 50% were relatively the same as the control. For the surface water quality, it appeared that $EC_i$ (electrical conductivity of irrigation water) and SAR (sodium adsorption ratio) values of DMWT (discharge waters from municipal wastewater treatment plant) irrigation were twofold higher than those of ground water irrigation as the control regardless of fertilization levels. For the irrigation periods, there were not significantly difference between 10 and 20 days of treatments, but $EC_i$ and SAR values of surface water were highest at 30 days of irrigation periods at initial rice growing stages. Generally, $EC_i$ values of percolation water in all the treatments were gradually increasing until 30days after irrigation, and then decreasing to harvest stage. Overall, it might be considered that there was possibility to irrigate DMWT with application of FAST 50% for 20 days of drought periods at rice transplanting season. Furthermore, efficiency rate of alternative irrigation water for 20 days of drought period was 32.7% relative to the total annual irrigation water for rice cultivation.