• 전자공학회논문지
• /
• 제52권1호
• /
• pp.135-139
• /
• 2015

플라즈마 디스플레이 패널의 각 부화면 시간동안 기입 방전의 지연시간을 각각 조사하였고 오방전이 발생하지 않는 범위내에서 추가 주사전압의 높이를 다르게 인가하여 모든 부화면 시간동안 기입방전 지연시간을 단축시키기 위한 수정된 구동방법을 제시한다. AC PDP에서 첫번째 초기화 기간 동안 주사전극에 높은 상승 경사파 전압을 인가하여 약한 플라즈마 방전이 발생하고 셀 내부에서 프라이밍 입자와 벽전하 생성을 유도한다. 생성된 벽전하는 셀 내부 벽전압이 되므로 기입기간 중 기입전압과 더해져서 기입 방전을 일으킨다. 그러나 셀 내부의 벽전하는 시간이 지나면서 점차 소멸되므로 1 TV 프레임 시간 동안 각 부화면 시간동안 기입방전은 늦게 발생한다. 첫 번째 부화면 시간에는 초기화 기간 동안 상승 경사파를 갖는 높은 전압에 의해 벽전하가 많이 남아 있으므로 첫 번째 기입 방전은 다른 부화면 시간보다 빠르게 형성된다. 한편, 두 번째부터 마지막 부화면 시간까지의 기입 방전 생성시간은 셀 내의 벽전하 소멸에 의하여 점차적으로 늦어진다. 본 연구에서는 각 부화면 시간동안 기입방전의 시간지연을 조사하였고, 부화면 시간의 기입기간 마다 추가 주사전압을 다르게 인가하여 전체 기입방전지연시간을 단축시켰다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2156-2159
• /
• 2005

ADS(Address Display Period Separation) driving method has been considered to be the most appropriate driving technique for AC PDP. ADS driving method is composed of reset, address, sustain and erase period. Therefore, a long time should be allocated to an address period, which results in a reduction of brightness. To realize a high luminance and high picture quality, it is necessary to high speed addressing. However, address discharge time lag increases as the temperature decreases, which can cause the misfiring and low picture quality In this paper, the electric field effect and priming particle effect are investigated in order to reduce the address discharge time lag at low temperature. Address discharge time lag was reduced effectively when the priming particles are provided.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권8호
• /
• pp.407-414
• /
• 2004

In this paper, a new gray scale expression method that divides the scan lines into multiple blocks is suggested. The proposed method can drive 16 sub-fields per 1 TV field in the panel with XGA ($1366{\times}768$) resolution. The on and off states of even subfields depend on the condition of odd subfields. The write address mode is used in the odd subfields, while the erase address mode is used in the even subfields. Because the ramp reset pulse is applied every 2 sub-fields, both the contrast ratio and the dynamic voltage margin are sufficiently obtained in comparison with previous AWD (Address While Display) methods. In realizing 16 subfields, shortening the scan time in the erase address period was important. The X bias voltage in the erase address period affected the minimum address voltage but did not the delay time of the address discharge. The delay time of the address discharge was affected by the address voltage and the time interval between the last sustain discharge and the scanning time. We also evaluated the dynamic false contour. New method shows an improved image quality in horizontal moving, but discontinuous lines were observed at the boundaries of each block in vertical moving

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.613-616
• /
• 2007

Characteristics of dark image retention and address discharge time lag were investigated simultaneously. It was found that reset waveforms with low black luminance did not guarantee lower image retention. Improved address discharge time lag due to modified reset waveforms similarly did not show improved image retention. The address discharge time lag and the image retention are in a trade-off relation.

• 한국정밀공학회지
• /
• 제21권9호
• /
• pp.174-181
• /
• 2004

Recently, many studies have been undergoing to reduce working time in field of machine tool. There are two ways of reducing working time to reduce actual working time by heighten spindle speed and to reduce stand-by time by shortening tool exchange time. Auto tool changer belongs to latter case. Fixed address type auto tool changer can store more number of tools in small space than magazine transfer Ope and can shorten tool exchange time. This study focuses on the topology optimization to reduce the weight of the fixed address type ATC. The optimization program using a real number coding genetic algorithm is developed and is applied to the 10-bar truss optimization problem to verify the developed program. And, it is shown that the developed program gives better results than other methods. Finally, The developed program applied to optimize the fixed address type ATC.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권2호
• /
• pp.1185-1188
• /
• 2007

The address discharge characteristics by the various scan-low and common-bias voltages are investigated based on measured address discharge time lags and $V_t$ close-curve analysis. The scan-low voltages are changed under the same voltage difference between the X and Y electrodes during an address period. As the voltage difference between the scan and address electrodes is increased during an address period, the address discharge time lag is shortened but the background luminance is increased. It is found that the improved address discharge characteristics is caused by the effect of the higher external applied voltage during an address period than the accumulated wall charges during a reset period and the high background luminance can be prevented by applying an address-bias voltage during a rising-ramp period and low reset voltage.

• 한국전기전자재료학회논문지
• /
• 제18권2호
• /
• pp.180-186
• /
• 2005

As a driving method of AC-PDP, Address-Display Separated(ADS) driving has been widely adopted for its simple architecture and low discharge failure rate. However, a high definition like a HDTV has defect of long addressing time by reason of a number of pixels. Priming effect isn't fully sustained because of long addressing time during the address period. Therefore, it has different wall charge and luminance of each addressing time in the sustain period. In this study, we suggest a new driving waveform on the address period to improve these defects. We applied a ramp waveform, instead of a square waveform, to an address period in ADS, for operating on the AC-PDP, which used the conventional gas [He-Ne-Xe]. When the ramp waveform is applied to the address period, we experimented for uniform wall charge and the improved luminance by sustained Priming effect at each addressing time in the sustain period.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1150-1153
• /
• 2003

Recently, Many studies have been undergoing to reduce a working time in a field of machine tool. There are two ways of reducing working time; to reduce actual working time by heighten spindle speed and to reduce stand-by time by shortening tool exchange time. Automatic tool change system belongs to the latter case. Fixed address type automatic tool change system that is being developed in this study can store more number of tool in small space than magazine transfer type automatic tool changer as well as shorten tool exchange time. In this paper, a simplified equivalent model of finite element method in order to analyze frame structure of fixed address type automatic tool change system is presented.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권2호
• /
• pp.1181-1184
• /
• 2007

The new self-priming addressing driving scheme was proposed to improve an address discharge time lag. It utilizes the priming effect maintaining the priming ramp discharge during an address period and the address discharge time lag is significantly improved. In this study, the basic characteristics of the priming ramp discharge are presented.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.726-729
• /
• 2003

A new driving method is proposed to reduce the address period. The scan time of new driving method overlaps with the next scan time during the discharge lag time. Thus, without reducing the address pulse width and the scan pulse width, the new addressing method can reduce the address period. The results show that the scan time of about 100ns ${\sim}$ 300ns can be overlapped without the misfiring,.