• 한국공작기계학회논문집
• /
• 제17권2호
• /
• pp.90-96
• /
• 2008

A pneumatic system was proposed to evaluate displacement accuracy of the pneumatic actuator without external load and to analyze capability of integration of the proposed valve system. The proposed pneumatic system consisted of a combination of pneumatic valves, two proximity sensors, and a programmable logic controller(PLC). The position controller is based on the PLC controller connected with the proximity sensors. Displacement accuracy of the pneumatic cylinder stroke was tested by varying air pressures of the supply and discharge-side and strokes of the pneumatic cylinder. The displacement accuracy of the pneumatic cylinder stroke increased as the supply and discharge side of air pressure increased at the stroke length of 133mm. Also the displacement accuracy increased as the stroke length increased with a fixed supply and discharge side of air pressure of the pneumatic cylinder as 3.5 and $4.5kg/cm^2$, respectively. The most accurate displacement of the pneumatic cylinder(i.e., standard deviation of 0.01 mm) was obtained at the supply and discharge side of air pressure of 4.0 and $5.0kg/cm^2$, respectively, and strokes of 170 and 190 mm among arbitrarily selected supply and discharge side air pressures and strokes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.879-882
• /
• 2005

This paper shows a method for design of the nano-positioning planar scanner used in the scanning probe microscope. The planar scanner is composed of flexure guides, piezoelectric actuators and feedback sensors. In the design of flexure guides, the Castigliano's theorem was used to find the stiffness of the guide. The motion amplifying mechanism was used in the piezoelectric actuator to achieve a large travel range. We found theoretically the travel range of the total system and verified using the commercial FEM(Finite element method) program. The maximum travel range of the planar scanner is above than 140 $\mu$m. The 3 axis positioning capability was verified by the mode analysis using the FEM program. Moreover, we presented the actual AFM(Atomic Force Microscope) imaging results with up to 2Hz imaging scan rate. Experimental results show that the properties of the proposed planar scanner is well enough to be used in SPM applications like AFM.

• 한국자동차공학회논문집
• /
• 제23권5호
• /
• pp.553-563
• /
• 2015

Reportedly the fatality rate from secondary collision is six times higher than the average fatality rate from all traffic accidents. So prevention of the secondary collision is attracting significant attention from automotive industries. However, the secondary collision prevention systems that have been developed are not considering possibility of brake actuator failure that can occur by the impact during the initial collision. In this paper, a new system has been developed that could prevent secondary collision even in case of brake actuator failure by taking advantage of still operating actuators. In this system, a steering control is performed for maintaining a lane by using linear quadratic regulator. Additionally, the system attempts differential brake control with the remaining braking capability to stop the vehicle in the shortest distance. Through simulation in various collision scenarios, the system has demonstrated significant potential of preventing secondary collision that could otherwise have resulted in severe fatality.

• 한국항공우주학회지
• /
• 제36권7호
• /
• pp.651-657
• /
• 2008

본 논문에서는 저사양의 반작용 휠을 이용하여 토크 가용성을 높이는 두 가지 기법이 제안 하였다. 첫 번째는 기존의 의사역행렬을 이용한 토크 제어 분배 법칙 대신 가중치가변 의사역행렬과 모멘텀을 최소화하는 제어 분배 법칙을 제안하여 반작용 휠의 토크, 모멘텀 제한 조건 내의 해를 찾도록 했다. 두 번째는 휠의 장착각을 변경하여 토크가 많이 필요한 축의 토크 가용성 자체를 증가시키는 방법을 제안하였다. 제안된 법칙들은 위성체의 자세 천이에 적용되었으며, 시뮬레이션을 통하여 성능 향상과 실제 위성의 적용 가능성을 기술했다.

• 제어로봇시스템학회논문지
• /
• 제5권3호
• /
• pp.288-296
• /
• 1999

A force-reflecting hand controller can provide the kinesthetic information obtained from a slave manipulator to the operator of a teleoperation system. The goal is to construct a compact hand controller that can provide large workspace and good force-reflecting capability. This paper presents the design and the analysis of a 6-degree-of-freedom force-reflecting hand controller using fivebar parallel mechanism. The forward kinematics of the fivebar parallel mechanism has been calculated in real-time using three pin-joint sensors in addition to six actuator position sensors. A force decomposition approach is used to compute the Jacobian. To evaluate the characteristics of the fivebar parallel mechanism, it has been compared with the other three parallel mechanisms in terms with workspace and manipulability measure. The hand controller using the fivebar parallel mechanism has been constructed and tested to verify the feasibility of the design concept.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.729-734
• /
• 2000

This paper proposes virtual-magnetic system by a force-reflecting interface to drive a ultrasonic motors(USMs) To approach virtual magnet in graphic the 6 dDOF force-reflecting interfaces provides force feedback to users as if I is magnetic-force, So users can feel real magnet Effectively to display the magnetic-force we need the interface with specific characteristics such as low inertia almost zero friction and very high stiffness As an actuator for the interface the USMs have many good advantage satisfied these conditions over conventional servo motors. To estimate capability of this virtual-magnetic system we did an experiment of magnetism based on coulomb's law when Coulmb's low apply this experiment it is vey conformable to real magnet

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1190-1194
• /
• 2007

Since the dismantling processes of building are very dangerous, there have been many studies to develop a remote operating devices using joystick. In this paper, in order to improve the operability of the dismantling actuator that is usually an excavator, a novel concept of tele-operated haptic device is proposed. Operators who use this haptic device with additional environmental sensing devices can work safely away from the dangerous sites. First, based on the concept design of the haptic device, the workspace mapping from the haptic device to the excavator is explored. Second, the kinematics which deals with the conversion from the 3 dimensional position information of the haptic device to the joint variable information of the backhoe is included. Lastly, 3D graphical simulation of both haptic device and the backhoe will be shown. This new design of the haptic device can be easily manufactured and gives the workers very convenient and transparent remote control capability.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.458-461
• /
• 1995

A new type of rotational motor which is developed has a resolution smaller than 10 $^{-4}$ radian and can be accessed for full rotational angles. The operation principle of the motor is based on inchworm motion of two belt driving mechanism. Flexure hinge mechanism, which is pertinent to symmetry construction of the motor, is designed to minimze the effort to frame and is analyzed by using finite element method. Depending on input signal amplitude, rotational angle by one cycle is varied form 0.2*10 $^{-4}$ rad to 9.76* $^{-4}$ rad. This shows that it has the capability of getting very small rotational angle by considering radius of rotor and amplitude of input signal.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.246-246
• /
• 2006

Ionic polymer-metal composite (IPMC) soaked with various ionic liquids was prepared by using polystyrene sulfonic acid-grafted poly(vinylidene fluoride-co-hexafluoropropylene) as ion-exchange membrane (IEM). The prepared IPMCs were effectively deformed three times larger and actuated for 300 times longer than those of Nafion with water at the same applied conditions. The experimental results indicated than the increase in the bending capability can be caused by the increase in the improved properties of the IEMs and ionic liquids such as uptake content and ionic conductivity. And air-operating stability of the IPMCs is appreciably governed by various physical and electrochemical properties of soaked solvents in IEMs.

• 한국분무공학회지
• /
• 제17권2호
• /
• pp.57-63
• /
• 2012

For reduction of CO, NOx and soot emission emitted by diesel diffusion combustion, the authors focused on injection actuator to improve fuel availability inside combustion chamber. In this study, it was investigated the internal dynamic characteristics of two-stage injection with diesel injectors with different driving type for the common rail direct injection by using the AMESim simulation code. The analysis parameter defined such as fuel pressure, injection hole's diameter and driven voltage. As the results, it was shown that the piezo-driven injector had a faster response and had better control capability than the solenoid-driven injector. It was found the piezo-driven injector can be utilized effectively as multiple injector than solenoid-driven injector.