• 한국안전학회지
• /
• 제35권3호
• /
• pp.96-104
• /
• 2020

The numerical simulations were conducted to investigate the thermal-fluid phenomena occurred inside the experimental apparatus during a PCCS, used to remove heat released in accidents from a containment of light water nuclear power plant, operation. Numerical simulations of the flow and heat transfer caused by wall condensation inside the containment simulation vessel (CSV), which equipped with 18 vertical heat exchanger tubes, were conducted using the commercial computational fluid dynamics (CFD) software ANSYS-CFX. Shear stress transport (SST) and the wall condensation model were used for turbulence closure and wall condensation, respectively. The simulation using the actual size of the apparatus. However, rather than simulating the whole experimental apparatus in consideration of the experimental cases, calculation resources, and calculation time, the simulation model was prepared only in CSV. Selective simulation was conducted to verify the effects of non-condensable gas(NC gas) concentration, CSV internal pressure, and wall sub-cooling conditions. First, as a result of the internal flow of CSV, it was observed that downward flow due to condensation occurred surface of the vertical tube and upward flow occurred in the distant place. Natural convection occurred actively around the heat exchanger tube. Due to this rising and falling internal flow, natural circulation occurred actively around the heat exchanger tubes. Next, in order to check the performance of built-in condensation model using according to the non-condensable gas concentration, CSV internal flow and wall sub-cooling, the heat flux values were compared with the experimental results. On average, the results were underestimated with and error of about 25%. In addition, the influence of CSV internal pressure and wall sub-cooling was small, but when the condensate was highly generated due to the low non-condensable gas concentration, the error was large compared to the experimental values. This is considered to be due to the nature of the condensation model of the CFX code. However, in spite of the limitations of CFD, it is valid to use the built-in condensation model of CFD for PCCS performance prediction from a conservative perspective.

• 대한소아치과학회지
• /
• 제37권2호
• /
• pp.240-245
• /
• 2010

제1형 신경섬유종증은 약 3000명당 1명 꼴로 발생되며 상염색체 우성유전질환이다. 피부의 카페오레반점 및 다발성 신경 섬유종과 피부, 신경계, 골격계, 내분비계, 혈관계의 다양한 이형성이 특징이다. 실제적인 구강 내 신경섬유종은 25%의 환자에서 발생한다고 알려져 있다. 제1형 신경섬유종증으로 진단된 만9세의 여아가 치은의 부종을 주소로 본원에 내원하였다. 하악 전치부 설측에 치은비대가 존재하였고, 환자의 사지와 몸통에서 갈색반점인 카페오레 반점을 확인할 수 있었다. 비대된 치은조직을 국소마취 하에 제거하였고, 조직검사를 시행한 결과 신경섬유종으로 확진하였다. 7개월 후 검사 결과 재발의 증거없이 양호한 치유를 보였다. 재발의 가능성이 있으므로 정기적인 검사가 필요하다.

• Journal of Chest Surgery
• /
• 제19권2호
• /
• pp.225-231
• /
• 1986

Pericardial adhesions following open heart surgery pose a special problems, increasing the risk of cardiac reoperation because of the danger of damaging the heart, coronary artery and veins, or grafts and also the fibrous tissue may obliterate the pericardial space and eventually constrict the heart. This study was undertaken to evaluate the effect of intrapericardial urokinase and dextran 40 on the formation of pericardial adhesions in an animal model. latrogenic traumas on the pericardium were surgically induced in 30 rabbits, simulating injuries possible during actual surgery. In all rabbits, blood [1 ml] was obtained from an ear vessel and injected into the pericardium. Control group of ten rabbits did not receive any further medication, urokinase group of ten received 15, 000-20, 000 IU of urokinase, and remained ten received 1 ml of 10% dextran 40. All rabbits were sacrificed at 4 weeks. At autopsy, the development of adhesions were graded as none [Grade I], minimal [Grade II], moderate [Grade III], and severe [Grade IV]. Histological studies of the parietal pericardium and epicardium were performed. The results were as follows: 1. Group 1[Control group] showed minimal adhesion in 40%, moderate in 50%, and severe in 10% of the group. Sharp dissections were necessary in 60% of adhesions. 2. Group II [Dextran group] showed no adhesions in 20%, minimal in 60%, and moderate in 20% of the group. 3. Group III [Urokinase group] showed no adhesions in 40%, minimal in 40%, and moderate in 20% of the group. Considering in this group, the adhesion activity was significantly suppressed [60% adhesions] compared to the control group [100% adhesions] [P < 0.05]. 4. Histological findings revealed mild serosal fibrosis in none adherent group, loose fibrous connections between two layers of pericardium in minimal adhesion group, tight fibrous connections in moderate adhesion group, and marked fibrous thickening and close attachment of two surfaces were noted in severe adhesion group. These data have revealed the decreased incidence of pericardial adhesions with urokinase and dextran 40.

• 조명전기설비학회논문지
• /
• 제23권4호
• /
• pp.56-61
• /
• 2009

본 논문은 축소형 모델 접지전극이 접속된 금속제 구조물 주변의 대지표면전위분포와 위험전압에 대하여 기술하였다. 접지에 관련된 문제를 실제 현장데이터로부터 적정한 결론을 도출하기는 매우 어려우므로 접지전극 주변의 전위분포와 접촉전압, 보폭전압의 산정에 축소형 모델시험을 사용한다. 본 연구에서는 균질토양을 모의하기 위해 직경이 1,100[mm] 반구형 용기를 사용하였다. 실험결과, 접지전극 주변의 대지표면전위는 매우 높게 나타났으며, 특히 접지전극의 직상부의 대지표면전위는 다른 위치에 비해 높게 나타났다. 접지전극의 매설깊이가 증가함에 따라 대지표면전위와 보폭전압은 낮아지지만 접촉전압은 높아지는 것으로 나타났다.

• 한국항해항만학회지
• /
• 제32권5호
• /
• pp.369-377
• /
• 2008

최근 컨테이너선의 대형화 추세와 항만간의 경쟁 가속화로 인해 컨테이너터미널의 효율적 운영과 생산성 향상에 대한 관심과 노력이 증대되고 있다. 특히 YT를 이용한 이송방식을 채택하고 있는 터미널의 경우 AGV(Automated Guided Vehicle)를 이용하고 있는 자동화터미널에 비해 상대적으로 경제성 및 운용효율성 측면에서 불리한 것이 사실이다. 최근 10여 년간 이와 같은 YT운용의 비효율성을 보완하기 위해 YT Pooling Operation 도입과 같은 노력이 계속되어 왔으나 개별 YT의 위치인식기능부재로 인한 제약으로 실질적인 효과는 미미한 수준이었다. 본 연구에서는 최근 주목받고 있는 RTLS(Real Time Location System) 기술을 활용하여 기존 YT Pooling Operation의 제약사항을 해결하는 새로운 개념의 YT Dynamic Operation 모델을 세안한다.

• 무역상무연구
• /
• 제49권
• /
• pp.3-41
• /
• 2011

In this article, the author have studied on main revisions and some recommendations of the Incoterms(R) 2010. Main revisions are as belows. 1. Two new Incoterms rules -DAT and DAP- have replaced the Incoterms 2000 rules DAF, DES, DEQ and DDU. 2. New classification of the Incoterms(R) 2010 are adopted. First class is Rules for any mode or modes of transport(EXW, FCA, CPT, CIP, DAT, DAP and DDP belong to this class.) and second class is rules for sea and inland waterway transport(FAS, FOB, CFR and CIF belong to this class.). 3. Incoterms(R) 2010 rules formally recognizes that they are available for application to both international and domestic sale contracts. 4. The Guidance Notes and Introduction are not part of the actual Incoterms(R) 2010 rules. 5. Under the FOB, CFR and CIF, all mention of the ship's rail as the point of delivery has been omitted in preference for the goods being delivered when they are "on board" the vessel. 6. Incoterms(R) 2010 rules include the obligation to 'procure goods shipped' as an alternative to the obligation to ship goods in the relevant Incoterms rules. 7. Incoterms(R) 2010 rules give electronic means of communication the same effect as paper communication. 8. Incoterms(R) 2010 rules have allocated obligations between the buyer and seller to obtain or to render assistance in obtaining security-related clearances. such as chain-of custody information. Some recommendations are as belows. 1. The parties must incorporate the Incoterms(R) 2010 rules into their contract of sale. 2. The parties must choose the appropriate Incoterms(R) 2010 rules. 3. Specify the place or port as precisely as possible in their contract of sale. 4. Remember that Incoterms(R) 2010 rules do not give the parties a complete contract of sale. 5. Incoterms(R) 2010 rules do not prohibit alteration of Incoterms rule, but there are dangers in so doings. In order to avoid any unwelcome surprises, the parties would need to make the intended effect of such alterations extremely clear in their contract.

• 비파괴검사학회지
• /
• 제31권5호
• /
• pp.479-486
• /
• 2011

의료영상을 기반으로 한 경동맥 분기부 혈류유동장 전산유체역학 해석의 수행에 있어 입구부 경계 조건 도출을 위한 환자 특정 시간 변동 상세 유속 분포를 얻는 것은 일반적으로 쉽지 않다. 그러므로 대부분의 경우 계측된 혈류량을 바탕으로 이상적인 축대칭 완전발달 유속 분포를 적용하게 된다. 그러나 MRI로 직접 계측한 총경동맥 혈류 유속분포를 적용한 기존의 연구에서 입구부 유속분포 경계 조건이 경동맥 분기부 혈류 유동장 해석 결과에 중요한 영향을 미친다는 것을 보였으며, 특히 계측된 혈류 유속분포가 전형적인 Dean type 유동과 다른 독특한 형태를 가진다는 것을 보고하였다. 본 연구에서는 이러한 독특한 형태의 유속 분포가 경동맥 입구부 형상의 이차곡률에 의해 생성됨을 보이고, 직접 경동맥 분기부 유동장 CFD 해석의 경계 조건으로 적용하여 이의 영향을 조사하였다. 이를 통하여 충분한 길이의 실제 경동맥 입구부 형상을 적용 할 경우, 입구부 경계 조건의 영향이 의료영상으로 부터 혈관 형상을 도출하는 과정에서 불가피하게 유기되는 영상 처리 오차에 의한 영향에 비해 상대적으로 크지 않음을 알 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권2호
• /
• pp.123-132
• /
• 2014

The maritime sector is advancing with dedicated endeavor to reduce greenhouse gas in addressing issues with regards to global warming. Since 01 January 2013, the International Maritime Organization (IMO) regulation mandatory requirement for Energy Efficiency Design Index (EEDI) has been in place and should be satisfied by newly-built ships of more than 400 gross tonnage and the Ship Energy Efficiency Management Plan (SEEMP) for all ships type. Therefore, compliance to this necessitates planning during the design stage whereas verification can be carried-out through an acceptable method during sea trial. The MEPC-approved 2013 guidance, ISO 15016 and ISO 19019 on EEDI serves the purpose for calculation and verification of attained EEDI value. Individual ships EEDI value should be lower than the required value set by these regulations. The key factors for EEDI verification are power and speed assessment and their synchronization. The shaft power can be measured by telemeter system using strain gage during sea trial. However, calibration of shaft power onboard condition is complicated. Hence, it relies only on proficient technology that operates within the permitted ISO allowance. On the other hand, the ship speed can be measured and calibrated by differential ground positioning system (DGPS). An actual test on a newly-built vessel was carried out to assess the correlation of power and speed. The Energy-efficiency Design Index or Operational Indicator Monitoring System (EDiMS) software developed by the Dynamics Laboratory-Mokpo Maritime University (DL-MMU) and Green Marine Equipment RIS Center (GMERC) of Mokpo Maritime University was utilized for this investigation. In addition, the software can continuously monitor air emission and is a useful tool for inventory and ship energy management plan. This paper introduces the synchronization and identification method between shaft power and ship speed for EEDI verification in accordance with the ISO guidance.

• 동력기계공학회지
• /
• 제21권2호
• /
• pp.64-69
• /
• 2017

The purpose of this study is to investigate the performance characteristics of seawater cooling system for a fishing vessel. The circulation amount of refrigerant, condensation capacity, evaporation capacity, compression work and coefficient of performance(COP) were analyzed as the heat source temperature changed. The experimental setup consisted of an open-type compressor, a shell&tube type condenser, an evaporator and an expansion valve. The heat source was controlled by a constant temperature chamber. The main results of this study are summarized as follows. The condensation capacity increased with increasing heat source temperature, and it was confirmed that the effect of circulating amount of refrigerant was dominant. The amount of heat for vaporization was almost constant even though the temperature of the heat source increased. On the other hand, the compression power was increased. This is because the compression ratio increases as the condensation pressure, the enthalpy difference between inlet and outlet, the amount of circulating refrigerant increases. The performance coefficient of this system showed a tendency decreasing with increasing heat source temperature. Therefore, the basic data of the seawater cooling system for the maintenance of the catch line of the shore fishing boats was acquired through this study, and it is considered that it will be sufficient for the actual design.

• Journal of Advanced Marine Engineering and Technology
• /
• 제39권9호
• /
• pp.981-986
• /
• 2015

지구온난화에 대한 심각성이 대두되면서 선박부문의 온실가스 배출에 관한 연구가 전 세계적으로 활발하게 진행되고 있다. 이에 반하여 국내 연구 수준은 기초에 그치고 있다. 본 논문에서는 선박으로부터 배출되는 이산화탄소의 여러가지 저감대책 중에서 운항손실과 투자비용을 최소화하면서 수행할 수 있는 방법으로 전자제어엔진 사용, 트림 최적화, 프로펠러 연마 및 친환경 방오도료의 사용을 선정하였다. 선정된 저감대책들을 운항실습선에 적용하여 시험 운항을 실시하였고 연료소비율에 미치는 영향을 분석하였다. 그 결과, 각 대책들은 약 1~5%의 연료소비율 저감 효과가 있었고 이를 에너지효율운항지수 산출에 적용하면 약 1~5%를 감소시키는 것을 알 수 있었다. 향후 국제적 환경규제를 제정할 때 우리나라에게 유리하도록 대응하기 위해서는 에너지효율운항지수에 대한 연구에도 지속적인 노력이 필요하다고 사료된다.