• Journal of the Speleological Society of Korea
• /
• no.78
• /
• pp.23-27
• /
• 2007

In this paper, we have investigated the characteristics of the magnetic abrasive using sludge on polishing of internal finishing of seamless stainless steel tube applying magnetic abrasive polishing. Either white alumina grain was used to resin sludge at a low temperature, and the sludge of magnetic abrasive powder was synthesized and crushed into 200 meshes. Surface roughness was measured before and after polishing, and more than 40% of improvement of surface roughness was achieved when grain was used under a specific condition. Even though some degree of surface roughness due to deeper scratches still exist, but the result showed a prospective magnetic abrasive polishing using sludge with white alumina grains.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.151-157
• /
• 2004

In this paper deals with behavior of the magnetic abrasive using sludge on polishing characteristics in a new internal finishing of seamless stainless steel tube applying magnetic abrasive polishing. The magnetic abrasive using sludge-abrasive grain WA and GC used to resin bond fabricated low temperature. And sludge of magnetic abrasive powder fabricated that sludge was crused into 200 mesh. The previous research have made an experiment in the static state the movement of magnetic abrasive grain is nevertheless in the dynamic state. In this paper, We could have investigated into the changes of the movement of magnetic abrasive grain. In reference to this result, we could have made the experiment which is set under the condition of the magnetic flux density, polishing velocity according to the form of magnetic brush.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1996.10a
• /
• pp.91-95
• /
• 1996

One must observe abrasive grain of grinding wheel and know their behaviors to understand the grinding mechanism. The behaviors of abrasive grain on the wheel surface. such as shapes distributions and changes were studied to make the grinding mechanism clear but the behaviors of abrasive grains on CBN wheel are not known enough. From this paper the working surface of a grinding wheel is observed by photography in which a picture of a wheel surface is taken by the camera through the microscope on the grinding machine and analyzed with the computer.

• Journal of the Korea Safety Management & Science
• /
• v.11 no.4
• /
• pp.311-317
• /
• 2009

In this paper deals with behavior of the magnetic abrasive using Ba-Ferrite on polishing characteristics in a new internal finishing of STS304 pipe applying magnetic abrasive polishing. The magnetic abrasive using Ba-Ferrite grain WA used to resin bond fabricated low temperature. And Ba-Ferrite of magnetic abrasive powder fabricated that Ba-Ferrite was crused into 200 mesh. The previous research have made an experiment in the static state the movement of magnetic abrasive grain is nevertheless in the dynamic state. In this paper, We could have investigated into the changes of the movement of magnetic abrasive grain. In reference to this result, we could have made the experiment which is set under the condition of the magnetic flux density, polishing velocity according to the form of magnetic brush.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.565-568
• /
• 2003

In this paper we deal with behavior of the magnetic abrasive using Ba-Ferrite on polishing characteristics in a new internal finishing of STS304 pipe applying magnetic abrasive polishing. The magnetic abrasive using Ba-Ferrite grain WA was used to resin bond fabricated at low temperature. And Ba-Ferrite of magnetic abrasive powder was crused into 200 mesh. The previous research made an experiment in the static and the dynamic state on the movement of magnetic abrasive grain. In this paper. We investigated into the changes of the movement of magnetic abrasive grain. In reference to this result. we have made the experiment which is set under the condition of the magnetic flux density. polishing velocity according to the form of magnetic brush.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.6
• /
• pp.1533-1541
• /
• 1990

Cubic boron nitride (CBN) is known the second hardest material followed diamond and was provided industry as an abrasive grain in the late 1960's. Since the introduction of CBN, a large amount of research has been carried out to determine the best application condition for grinding operation. Despite the advantages in its characteristics, CBN has not yet gained full acceptance as more excellent abrasive grain than traditional one. The reason for this state is that the surface roughness ground by CBN is worse than by traditional one and dressing and truing is very difficult. This led user's resistance to the use of CBN as an abrasive grain. Present study is to investigate the cause of lower surface roughness ground by CBN single crystal abrasive grain comparing with traditional one.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.77-80
• /
• 2004

In this paper, we have investigated the characteristics of the magnetic abrasive using sludge on polishing of internal finishing of seamless stainless steel (STS304) tube applying magnetic abrasive polishing. Either white alumina (WA) or green carborundum (GC) grain was used to resin sludge at a low temperature, and the sludge of magnetic abrasive powder was synthesized and crushed into 200 meshes. Surface roughness was measured before and after polishing, and more than 40% of improvement of surface roughness was achieved when WA grain was used under a specific condition. Even though some degree of surface roughness due to deeper scratches still exist, but the result showed a prospective magnetic abrasive polishing using sludge with WA or GC grains.

• Transactions on Electrical and Electronic Materials
• /
• v.6 no.3
• /
• pp.128-132
• /
• 2005

In this paper, we have investigated the characteristics of the magnetic abrasive using sludge on polishing of internal finishing of seamless stainless steel (STS304) tube applying magnetic abrasive polishing. Either white alumina (WA) or green carborundum (GC) grain was used to resin sludge at a low temperature, and the sludge of magnetic abrasive powder was synthesized and crushed into 200 meshes. Surface roughness was measured before and after polishing, and more than $40\%$ of improvement of surface roughness was achieved when WA grain was used under a specific condition. Even though some degree of surface roughness due to deeper scratches still exist, but the result showed a prospective magnetic abrasive polishing using sludge with WA or GC grains.

• Journal of the Speleological Society of Korea
• /
• no.82
• /
• pp.8-12
• /
• 2007

In this paper, we have investigated the characteristics of the magnetic abrasive using sludge on polishing of internal finishing of seamless stainless steel tube applying magnetic abrasive polishing. Either green carborundum(GC) grain was used to resin sludge at a low temperature, and the sludge of magnetic abrasive powder was synthesized and crushed into 200 meshes. Surface roughness was measured before and after polishing, and more than 38% of improvement of surface roughness was achieved when grain was used under a specific condition. Even though some degree of surface roughness due to deeper scratches still exist, but the result showed a prospective magnetic abrasive polishing using sludge with green carborundum grains.

• Journal of Biosystems Engineering
• /
• v.35 no.3
• /
• pp.169-174
• /
• 2010

This study was conducted to investigate the effect of abrasive processing and non abrasive processing in the milling process on the quality of rice. The effect was analyzed based on the factor such as whiteness, grain temperature, moisture content, crack and broken rice ratio. The results were as followings. Whiteness of abrasive rice was the same as non abrasive rice. The rice temperature increase of abrasive rice was $1.6^{\circ}C$ lower than non abrasive rice. The crack ratio was increased in the process of milling and non abrasive rice showed higher values than abrasive rice. The broken rice ratio of the using abrasive processing was about 0.05% lower than that of non abrasive processing. The moisture content decreased in the process of milling regardless of the use abrasive rice milling machine.