• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.10a
• /
• pp.435-438
• /
• 2012

Today, In all fields, As combination of ubiquitous computing-based technologies between electronic space and physical space, has been active trend research about wireless integration sensor network between sensors and wireless technology. Also, but in ship is underway research about Ship Area Network(SAN) of intelligent ship to integrate wireless technology, ship is required SAN-bridge technology of a variety of wired, wireless network integration and heterogeneous sensor and interoperability of the controller and SAN configuration management technology of remote control. Ship keep safe of all the surrounding environment including crew besides structural safety and freight management monitoring. In this paper, for monitoring design such as on climate change detection and temperature, pressure about various structures, there identify technology trends for routing and data aggregation to use energy efficiency in wireless sensor network. And to analyze self-organizing clustering method, study For wireless sensor network configuration in ship.

• Advances in aircraft and spacecraft science
• /
• v.6 no.2
• /
• pp.117-144
• /
• 2019

High Altitude and Long Endurance (HALE) aircraft are capable of providing intelligence, surveillance and reconnaissance (ISR) capabilities over vast geographic areas when equipped with advanced sensor packages. As their use becomes more widespread, the demand for additional range, endurance and payload capability will increase and designers are exploring non-conventional configurations to meet the increasing demands. One such configuration is the joined-wing concept. A joined-wing aircraft is one that typically connects a front and aft wings in a diamond shaped planform. One such example is the Boeing SensorCraft configuration. While the joined-wing configuration offers potential benefits regarding aerodynamic efficiency, structural weight, and sensing capabilities, structural design requires careful consideration of elastic buckling resulting from the aft wing supporting, in compression, part of the forward wing structural loading. It has been shown already that this is a nonlinear phenomenon, involving geometric nonlinearities and follower forces that tend to flatten the entire configuration, leading to structural overload due to the loss of the aft wing's ability to support the forward wing load. Severe gusts are likely to be the critical design condition, with flight control system interaction in the form of Gust Load Alleviation (GLA) playing a key role in minimizing the structural loads. The University of Victoria Center for Aerospace Research (UVic-CfAR) has built a 3-meter span scaled and flexible wing UAV based on the Boeing SensorCraft design. The goal is to validate the nonlinear structural behavior in flight. The main objective of this research work is to perform Ground Vibration Tests (GVT) to characterize the dynamic properties of the scaled flight vehicle. Results from the experimental tests are used to characterize the modal dynamics of the aircraft, and to validate the numerical models. The GVT results are an important step towards a safe flight test program.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.527-530
• /
• 2010

WSN is composed of a lot of small sensors with the limited hardware resources. In WSN, at the initial stage, sensor nodes are randomly deployed over the region of interest, and self-configure the clustered networks by grouping a bunch of sensor nodes and selecting a cluster header among them. Specially, in WSN environment, in which the administrator's intervention is restricted, the self-configuration capability is essential to establish a power-conservative WSN which provides broad sensing coverage and communication coverage. In this paper, we propose a communication coverage-aware cluster head election algorithm for Herearchical WSNs which consists of communication coverage-aware of the Base station is the cluster head node is elected and a clustering.

• Journal of Internet Computing and Services
• /
• v.15 no.4
• /
• pp.111-118
• /
• 2014

In mobile sensor networks, a large number of sensor nodes with battery powered are deployed randomly in a region. They monitor the environmental states and transmit data to its neighboring nodes. For mobile sensor networks, It is needed to maintain the connectivity autonomously among nodes as the sensor node moves. However, the existing works have focused on the energy savings in the fixed sensor networks. A specific algorithm considering node mobility is required in the mobile sensor networks. Along with energy efficiency, the transmission delay should be considered. In this paper, we propose an autonomous configuration scheme and a node scheduling algorithm when a moving node joins into the existing network. Through simulations, we show a superior performance of the proposed algorithm to the existing protocol.

• Journal of the Korean Ceramic Society
• /
• v.42 no.1
• /
• pp.11-15
• /
• 2005

The configuration of the main components and the physical structure of the Taguchi sensor, the first ceramic gas sensor mass produced, has remained virtually unaltered since its appearance 40 years ago. This device owns an excellent combination of the quality factors but is non-selective. The research efforts carried out to enhance the selectivity in this resistive gas sensor are briefly reviewed. A novel design, Capillary-attached Gas Sensor (CGS), is introduced, which employs the same ceramic components used for the fabrication of a classical Taguchi sensor but in altered geometries. CGS presents remarkable advantages from the view point of selectivity over the original design. While the steady state response of a CGS has the same significance as that of the Taguchi sensor, its transient response presents valuable diagnostic information. Fabrication and test of a prototype CGS is reported.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.1
• /
• pp.57-66
• /
• 2001

In order to measure steel corrosion in mortar by a transient electro-magnetic (TEM) Method, the development of the sensors have been studied. The sensors were made of enamelled wire with diameter of 0.25mm and Acril. The sensor configuration was used as a coincident loop type. The secondary electro motive force(EMF) was measured with SIROTEM III. The accelerator was equipped with the SIROTEM III. The accelerator permits the transmitter to turn off approximately 10~15 times faster than normal. The high resolution time series used for very shallow or high resistivity investigation was selected. The steels were embedded in mortar which were made from sand : cement : water ratio of 2 : 1: 0.5. The mortar specimen was 50cm long, 20cm wide and 10cm thick. To investigate steel corrosion in mortar, the sensors used were with 2$\times$2$cm^2$(3, 6, 9$\Omega$), 3$\times$3$cm^2$(3, 6, 9$\Omega$) and 6$\times$6$cm^2$(3, 6, 9$\Omega$). The obtained result obtained showed that the sensor 8(6$\times$6$cm^2$, 6$\Omega$) was the proper sensor for the measurement of steel corrosion in mortar.

• Journal of Mechanical Science and Technology
• /
• v.15 no.10
• /
• pp.1369-1379
• /
• 2001

This paper focuses on a development of a sensor system measuring locations of a vehicle to localize a mobile robot while it tracks on the track (location sensor) . Also it focuses on a system configuration identifying the vehicle's orientation and distance from the object while it is stationary at certain station (position sensor) . As for the location sensor it consists of a set of sensors with a combined guiding and counting sensor, and an address-coded sensor to localize the vehicle while moving on the rail. For the position sensor a PSD (Position Sensitive Device) sensor with photo-switches sensor to measure the offset and orientation of the vehicle at each station is introduced. Both sensor systems are integrated with a microprocessor as a data relay to the main computer controlling the vehicle. The location sensor system is developed and its performance for a mobile robot is verified by experiments. The position measuring system is proposed and is robust to the environmental variation. Moreover, the two kinds of sensor systems guarantee a low cost application and high reliability.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.101-104
• /
• 2007

Efficient Query processing and optimization are critical for reducing network traffic and decreasing latency of query when accessing and manipulating sensor data of large-scale sensor networks. Currently it has been studied in sensor database projects. These works have mainly focused on in-network query processing for sensor networks and assumes homogeneous sensor networks, where each sensor network has same hardware and software configuration. In this paper, we present a framework for efficient query processing over heterogeneous sensor networks. Our proposed framework introduces query processing paradigm considering two heterogeneous characteristics of sensor networks: (1) data dissemination approach such as push, pull, and hybrid; (2) query processing capability of sensor networks if they may support in-network aggregation, spatial, periodic and conditional operators. Additionally, we propose multi-query optimization strategies supporting cross-translation between data acquisition query and data stream query to minimize total cost of multiple queries. It has been implemented in WSN middleware, COSMOS, developed by ETRI.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.517-520
• /
• 2008

Wireless sensor network supporting healthcare environment should provide customized service in accordance with context information such as continuous location change and status information for people or movable object. In addition, we should consider data transmission guarantees a person's bio information and privacy security provided through sensor network. In this paper analyzes LEACH protocol which guarantees the dynamic self-configuration, energy efficiency through configuration of inter-node hierarchical cluster between nodes and key distribution protocol used for security for data transmission between nodes. Based on this analysis result, we suggested self-configuration routing protocol supporting node mobility which is weakness of the existing LEACH protocol and data transmission method by applying key-pool pre-distribution method whose memory consumption is low, cluster unit public key method to sensor node.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.176-182
• /
• 1999

This paper presents a new autonomous kinematic calibration technique by using a laser-vision sensor called "Perceptron TriCam Contour". Because the sensor measures by capturing the image of a projected laser line on the surface of the object, we set up a long, straight line of a very fine string inside the robot workspace, and then allow the sensor mounted on a robot to measure the point intersection of the line of string and the projected laser line. The point data collected by changing robot configuration and sensor measuring are constrained to on a single straght line such that the closed-loop calibration method can be applied. The obtained calibration method is simple and accurate and also suitable for on-site calibration in an industrial environment. The method is implemented using Hyundai VORG-35 for its effectiveness.