• ETRI Journal
• /
• v.32 no.5
• /
• pp.819-822
• /
• 2010

Supporting QoS over multihop wireless mesh networks is difficult because end-to-end delay increases quickly with the increasing number of hops. This paper introduces a novel multichannel time-division multiple-access media access control (McTMAC) protocol that can help to efficiently reduce delay over multihop networks. Performance evaluation results demonstrate that McTMAC outperforms existing alternative protocols. The max-delay can be reduced by as much as 60% by using McTMAC.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.6
• /
• pp.60-66
• /
• 2010

Mesh grounding electrodes in Korea and abroad are designed as lattice-shaped equidistance grounding grids. In case of a lattice-shaped grounding Grid, however, there is a problem of higher touch voltage at the corner of the grid relative to the center. To overcome this problem, we used oblique-shaped equidistance grounding grid to reduce the area of the corner where mesh voltage occurs. As a result the mesh voltage was reduced. Therefore, this paper suggests the use of oblique-shaped grounding grid instead of the existing lattice-shaped ones. It applied the same grounding design dimensions for both lattice-shaped and oblique-shaped grounding grids, compared and analyzed mesh voltage, GPR, ground resistance, total length of grounding conductor, verified that oblique-shaped grounding grid is superior to the lattice-shaped.

• Journal of Power System Engineering
• /
• v.4 no.1
• /
• pp.60-67
• /
• 2000

As the speed of rotating machines increases and also their weight decreases, the coupling between lateral and torsional vibrations must be considered. In the past, rotordynamics and geardynamics have tended to treat the lateral and torsional vibrations of the system elements as separate and decoupled mechanisms. In the paper, the coupled lateral-torsional free and forced vibration of rotors trained by gears is analyzed using finite element method. Also the complicated variation of the meshing stiffness as a function of contact point along the line of action is estimated correctly. The gear mesh model is assumed to be linear with constant average mesh stiffness.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.5
• /
• pp.54-60
• /
• 2013

There is increasing demand for practical groundings for small-area substations because of the recent revision of Korea's Electrotechnical Regulations, which necessitates the method of evaluating their safety. This paper proposes a practical mesh grounding system for 22.9kV substations and studies how to evaluate its safety. The proposed grounding system is proved to obey the safety criteria of ANSI/IEEE Std. 80 via ANSI/IEEE Std. 80 method and computer simulation.

• International Journal of Safety
• /
• v.8 no.2
• /
• pp.20-25
• /
• 2009

In this study, an experiment in the field was performed to analyze the mechanical properties and the influence of steel fiber and silica fume on the rebound ratios of shotcrete. The experimental parameters which are the reinforcing methods (steel fiber, wire mesh), steel fiber contents (0.0%, 0.5%, 0.75%, 1.0%), silica fume contents (0.0%, 10.0%), layer thickness (60 mm, 80 mm, 100 mm), and the placing parts (sidewall, shoulder, crown) were chosen. From the mechanical test, it was found that the flexural strength and toughness is significantly improved by the steel fiber and/or silica fume. According to the results for the side wall in this test, the larger the fiber contents are in case of steel fiber reinforced shotcrete, the less the rebound ratios are within the range of 20-35%, compared to the wire mesh reinforced shotcrte. And also, the reduced rebound ratios were very larger in using steel fiber reinforced shotcrete with silica fume content of 10%, and these results are true of the shoulder and the crown. respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.6
• /
• pp.505-516
• /
• 2009

The effects of wood species, particle size of wood flours and coupling treatment on the mechanical properties of wood plastic composites (WPC) are investigated in this study. Chemical components of wood flour from 3 different wood species were analyzed by the chemical analysis. Wood flours of 40~60 mesh and 80~100 mesh were manufactured from Larix (Larix kaempferi Lamb.), Quercus (Quercus accutisima Carr.), and Maackia (Maackia amuresis Rupr. et Maxim). The wood flours were reinforced into polypropylene (PP) by melt compounding and injection molding, then tensile, flexural, and impact strength properties were analyzed. The order of alpha-cellulose content in wood is Quercus (43.6%), Maackia (41.3%) and Larix (36.2%). The order of lignin content in wood is Larix (31.6%), Maackia (24.7%), and Quercus accutisima (24.4%). The content of extractives in wood is in the order of Larix (8.5%), Maackia (4.4%), and Quercus accutisima (3.9%). As the content of alpha-cellulose increases and the lignin and extractives decreases, tensile and flexural strengths of the WPC increase. At the same loading level of wood flours, the smaller particle size (80~100 mesh) of wood flours showed highly improved tensile and flexural strengths, compared to the larger one (40~60 mesh). The impact strength of the WPC was not significantly affected by the wood species, but the wood flours of larger particle size showed better impact strengths. The addition of maleated polypropylene (MAPP) provided the highly improved tensile, flexural and impact strengths. Morphological analysis shows improved interfacial bonding with MAPP treatment for the composites.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.48 no.1
• /
• pp.10-19
• /
• 2012

The mesh selectivity of a drift net for yellow croaker (Larimichthys polyactis) was examined in field experiments with six different net mesh size (40, 45, 50, 55, 60 and 65mm) from April to December, 2008 in the coastal areas of Jeollanam-do in Korea. The total catch of 6,748 consisted of yellow croaker (n=6,310; 89.1% of total catch), common mackerel (n=158; 5.6%) and other species (n=280; 9.6%). The selectivity curve for yellow croaker was fit by the models of selectivity curve in SELECT method. The optimal mesh size for 50% retention for minimum landing size (191mm) of yellow croaker was estimated as 49.6mm-51mm by selectivity curves. And the bi-normal model for the selectivity curve was found to fit the data best.

• Food Science and Preservation
• /
• v.6 no.1
• /
• pp.76-80
• /
• 1999

Power consumption, mesh size, moisture content, color difference, amylogram of rice flour milled with the water soaked rice were compared with that of rice using dry pin mill process. The rice was soaked in 23, 24, 25, 26% of water for 10hr, independently. The more rice had moisture content, the less power consumption was needed. Power consumption to mill the rice soaked in 25% of water was less than that of dry rice by 6.8kW/100Kg. Moisture content of rice flour from the rice soaked with 25% of water was 2% higher than that of rice flour from the rice soaked with 23% of, water. Population of flour particle from the rice soaked with 24-25% of water was 45.7∼46.25 of 60 mesh, 9.7∼10.4% of 80∼100 mesh and 7.7∼8.1% of 100 mesh. Gelatinization temperature of rice flour from the rice soaked with 23% and 24∼25% of water was 65.70C and 64.50C, independently. Temperature of rice flour from the rice soaked with 23% 24∼25% of water sith minimum viscosity was 85.50C and 88.4∼88.70C, independently. Brightness and whiteness of the rice flour from the rice soaked with 24∼25% of water were 95.90∼95.95 and 905.82∼95.94, independently. Brightness and whiteness of the rice flour from the soaked rice were 1.2 and 1.7 higher than that of rice flour from the dry rice, independently.

• Journal of the Korean Society of Tobacco Science
• /
• v.26 no.2 s.52
• /
• pp.126-134
• /
• 2004

Tobacco dust samples were collected for two times in primary and secondary process at 4 cigarette manufacturing factories(Shintanzin, Youngju, Wonju, Kwangju) and analyzed to evaluate usage as a raw material in production of reconstituted tobacco. The chemical constituents and HWS of tobacco dust were analyzed. Tobacco dust samples were partitioned by particle size using a series of screens ranging from 20 to 200 mesh. The amount of material retained in each fraction was quantified and sand content was also determined. Appreciable average amounts$(40-65\%)$ material at 4 locations were found to be larger than 60 mesh. Although the amount of material in each fraction increased to a maximum at 100 mesh and then decreased, the $\%$ sand continually increased with decreasing particle size. The chemical constituents and HWS content of tobacco dust have similar values in secondary process of 4 cigarette manufacturing factories but the those of primary process have different values according to the site of occurrence and manufacturing factories.

• Journal of Biosystems Engineering
• /
• v.30 no.4 s.111
• /
• pp.195-201
• /
• 2005

The output of Stirling engine is influenced by the regenerator effectiveness. The regenerator effectiveness is influenced by heat transfer and flow friction loss of the regenerator matrix. In this paper, in order to provide a basic data for the design of regenerator matrix, characteristics of heat transfer and flow friction loss were investigated by a packed method of matrix in the oscillating flow as the same condition of operation in a Stirling engine. As matrices, several kinds of combined wire screen meshes were used. The results are summarized as follows; The packed meshes with high mesh no. in the side of heater part of regenerator showed effective than the packed meshes with low mesh no. in the side of cooler part of regenerator. The temperature difference and pressure drop of the regenerator were not made by the specific surface area of wire screen meshes but by the minimum free-flow area to the total frontal area. Among the No. 150 single screen meshes, 200-60 combined meshes, the 200-150-100 combined meshes showed the highest in effectiveness.