• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1248-1258
• /
• 2010

In this paper, a method for simultaneously realizing the sum and difference patterns which are required in the monopulse radar sensor systems, is presented by using single taper array antenna with rectangular microstrip patches. The widths of patches are first determined by the voltage weights which are synthesized for the fundamental array factor patterns to be applied to the monopulse operation by using the sidelobe levels(SLLs) control technique. As the bi-directionally series-fed technique is applied and the lengths of connecting lines between patches are appropriately adjusted, the single array generates two phase-shifted beams which activates out-of-phase and in-phase ports of a $180^{\circ}$ hybrid coupler to synthesize the sum and difference patterns. The simulated results on the configuration designed at 9.5 GHz are compared with measured results showing the validity of the proposed method.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.9
• /
• pp.54-61
• /
• 2016

A 6-Gbps single-ended receiver with a linear equalizer and a self-reference generator is proposed for a high-speed interface with the double data rate. The proposed single-ended receiver uses a common gate amplifier to increase a voltage gain for an input signal with low voltage level. The continuous-time linear equalizer which reduces gain to the low frequencies and achieves high-frequency peaking gain is implemented in the common gate amplifier. Furthermore, a self-reference generator, which is controlled with the resolution 2.1 mV using digital averaging method, is implemented to maximize the voltage margin by removing the offset noise of the common gate amplifier. The proposed single-ended receiver is designed using a 65-nm CMOS process with 1.2-V supply and consumes the power of 15 mW at the data rate of 6 Gbps. The peaking gain in the frequency of 3 GHz of the designed equalizer is more than 5 dB compared to that in the low frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.9
• /
• pp.1013-1022
• /
• 2010

In this paper, we propose a C-band radiometer for remote sensing of land surface temperature and present its experiment results using asphalt as target. Total power type is selected for high sensitivity and low power consumption, super-heterodyne type is selected for stable high gain. A radiometer designed at 5.1 GHz to have operating bandwidth of 110 MHz has system gain of 59 dB, noise figure of 2.7 dB and receiving sensitivity of 0.45 K. We have measured surface temperature on asphalt by using implemented system and thermometer. Analysis data of each measurement results show that a radiometer operates linearly with output voltage variation rate of 6 $mV/^{\circ}C$. As a result, we verified validity of a developed C-band radiometer for remote sensing of land surface temperature.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.10a
• /
• pp.223-228
• /
• 2007

In this paper, Wideband antenna using E-shaped stacked patches has been designed and fabricated for 4th generation mobile communication(IMT-Advanced) AccessPoint application. E-shaped patch was miniature and brodband by made the movement route of current long. And inductive of coaxial probe compensates capacitive by slot. Therefore we fabricated to improve the bandwidth of proposed antenna. The E-shaped single patch antenna has an impedance bandwidth of about 13%(510[MHz]), By adding a second patch at the top of the first patch a bandwidth of 56%(2060[MHz]). The final fabricated antenna could have a good return loss(Return loss ${\leq}-10dB$) and a high gain(over 9.6dBi) at the range of 3.23 ${\sim}$ 5.29 [GHz].

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.141-146
• /
• 2009

In this paper, a novel harmonic control circuit has been proposed for the design of high-efficiency power amplifier with Si LDMOSFET. The proposed harmonic control circuit haying the short impedances for the second- and third-harmonic components has been used to design the in/output matching network. The efficiency enhancement effect of the proposed harmonic control circuit is superior to the class-F or inverse class-F harmonic control circuit. Also, when the proposed harmonic control circuit has been adapted to the input matching network as well as the output matching network, the of ficiency enhancement effect of the proposed power amplifier has increased all the more. The measured maximum power added efficiency (PAE) of the proposed power amplifier is 82.68% at 1.71GHz band. Compared with class-F and inverse class-F amplifiers, the measured maximum PAE of the proposed power amplifier has increased in $5.08{\sim}9.91%$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.9
• /
• pp.1042-1047
• /
• 2012

In order to obtain balanced ports matching and isolation between balanced ports of a Marchand balun, a compact isolation network is proposed. The proposed compact isolation network is designed using composite right/left-hand (CRLH) transmission line and compact phase inverter using CRLH transmission line unit cell. Also, design method and analysis of proposed isolation network are presented. The sizes of the proposed isolation networks are significantly reduced to $0.11{\lambda}_g$ and $0.07{\lambda}_g$ compared with the conventional isolation network of $0.5{\lambda}_g$. The Marchand balun is operated at 2.45 GHz and is demonstrated through excellent experimental results.

• Korean Journal of Remote Sensing
• /
• v.28 no.2
• /
• pp.237-243
• /
• 2012

In this paper, an atmospheric effect of repetitive measurements of X-band (9.65 GHz) arc-rail type GB-SAR (ArcSAR) system was quantitatively analyzed. Four artificial triangular trihedral corner reflectors as stationary targets for getting stable back scattered signal during 43 hours continually. The results of the analysis showed that the phase of those stationary targets had changed maximum of 5 radian (12.4 mm) and total RMS error had was 1.62 radian (4 mm) during 65 repeated measuring time. The refractive index of air which was calculated using the temperature;humidity and pressure of atmosphere showed very close relationship with the phase difference. We could check the atmospheric correction was fulfilled by the correction of an atmospheric effect using refractive index during the selected 16 hours period showed that RMS error was dropped from 1.74 radian (4.3 mm) to 0.10 radian (0.24 mm).

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.5
• /
• pp.943-948
• /
• 2018

In this paper, SSPA Module for X-band radar was designed and fabricated by using GaN MMIC. For the purpose of configuring the high power SSPA module, the drive steamers are composed of 2-layers of GaN MMIC with considering Gain Loss. In addition, the power divider and power combiner used a 4way approach by designing a 4-stage power amplifier. The power divider has a loss of -3.0dB or more, and the I/O has a loss of -0.2dB in the power combiner and the phase difference between the ports are good at $2^{\circ}$ on average. The fabricated SSPA module got the measurement results that satisfy a Gain 48dB, P(sat)=88.3W(49.46 dBm), PAE=30.3% or more efficiency in condition of frequency range 9~10GHz. The fabricated X-Band SSPA module can be applied in RF performance improvement for SSPA module whit improvement of power divider/combiner.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2006.05a
• /
• pp.595-598
• /
• 2006

In this letter, a compact rectangular spiral antenna is proposed. Instead of a center excitation of conventional spiral antennas, the proposed antenna is adopted a modified feed network, feeding at the end of the spiral. The matching circuit of $'{\sqsupset}'$ shape is added at the feeding point. With this matching circuit, we can easily match the input impedance well, without the limit of the space. The parameter which determines the circular wave characteristic is explained, and the design guideline of the proposed antenna is presented. We design a proposed antenna operating at 9.5 GHz. Its size is only $0.6\lambda_g\times0.6\lambda_g$. The simulated bandwidth of the input impedance $(S11\leq-10)$ is 8.12% and that of $(AR\leq-3)$ is 4.62%, which is excellent characteristics as compared to its simple structure.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.3
• /
• pp.173-179
• /
• 1999

The defects on the metal surface. such as the ended circular pressed hole. the penetrated circular drilled hole, and the linear hollow lanes have been investigated by means of the microwave. In this experiment, frequency was set at 9.2GHz with 3kHz modulation, and the methods of reflection, transmission, fixed carrier frequency, and mod-demodulated technique have been used for investigating defects. The magnitudes of the microwave signals have been changed at the ended circular pressed hole and the penetrated circular drilled hole. The defect sizes that were estimated from the reflected microwave signals had the dimensions enlarged by twice the original size of the penetrated circular drilled hole and 2.5 times the original size of the ended circular pressed hole. The magnitudes of the reflected microwave signals from the linear hollow lane have increased with expansion of the width of the notch. In the linear hollow lane with the depth of 2.4mm, the reflected microwave signals versus the defect widths had a maximum value at the defect width of 50mm, and in the linear hollow lanes with the depths of 1.2mm and 0.45mm, the reflected microwave signals versus the defects widths had the maximum values each at the defect depths of 55mm.