• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.5
• /
• pp.468-474
• /
• 2010

In this paper, a VCHO(Voltage Controlled Harmonic Oscillator) for K-band application has been designed and implemented. The proposed oscillator has a structure of two hair-pin resonators placed on input and output of active device. Using in/out common frequency tuning structure, the VCHO yields some advantages of the enhanced fundamental frequency suppression characteristic as well as the improved output power of second harmonic. According to implementation and measurement results, it was shown that a VCHO provides an output power of -2.41 dBm, a fundamental frequency suppression of -21.84 dBc, and phase noise of -101.44 dBc/Hz at 100 kHz offset. In addition, as for the bias voltage from 0 V to -10 V for the varactor diode, output frequency range of 10.58 MHz is obtained with a power variation of ${\pm}0.19\;dB$ over its frequency range.

• Journal of Satellite, Information and Communications
• /
• v.3 no.1
• /
• pp.8-14
• /
• 2008

In this paper, we analyze throughput performance of MF-TDMA scheme and QS MC-DS/CDMA(quasi-synchronous MC-DS/CDMA) scheme based on scrambling on WH sequence and PPGC sequence in early frequency offset caused by high speed transfer terminal. QS MC-DS/CDMA scheme with scrambled WH sequence shows 5.7% higher throughput than MF-TDMA scheme and 8% higher throughput than QS MC-DS/CDMA with PPGC sequence in high speed transfer terminal environment such as maximum 1000Km/h speed with high frequency of Ka-band. Finally, we show that QS MC-DS/CDMA scheme with scrambled WH sequence is more efficient than traditional MF-TDMA scheme at the aspect of throughput in DVB-RCS system with Ka frequency band.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.11B
• /
• pp.1612-1619
• /
• 2001

This paper examines the design, implementation characteristics of a folded dipole active integrated antenna. Our goal was to minimize the physical size of RF circuit and its insertion loss, and to make the high frequency tuning easier by directly integrating the ISM(Industrial Scientific & Medical) band power amplifier and antenna. Non-linear model has been used for highly accurate simulation of the power amplifier. The maximum power level was found by using the Load pull method before an impedance matching was achieved. It is found that the total power-added efficiency(PAE) including the driving amplifier was 31.5% and that the transmit power was 13.7 dBm. We also found that the proposed scheme with the smaller antenna as compared with the existing dipole antenna has 23.7 dB total gain including the antenna gain. The suppression of the second harmonic signal to the fundamental signal with respect to the fundamental signal was found to be more than 30 dBc.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1550-1551
• /
• 2006

An L-band linear accelerator system for e-beam sterilization is under design for bio-technology application. The klystron-modulator system as RF microwave source has an important role as major components to offer the system reliability for long time steady state operation. A PFN line type pulse generator with a peak power of 71.5-MW, $7{\mu}s$, 285 pps is required to drive a high-power klystron. The high power pulse transformer has a function of transferring pulse energy from a pulsed power source to a high power load. The pulse transformer producing a pulse with a peak voltage of 275 kV is required to produce 30-MW peak and 60 kW average RF output power at the frequency of 1.3-GHz. We have designed the high power pulse transformer with 1:13 step-up ratio. The peak and average power capability is 71.5-MW (275 kV, 260 A at load side with $7{\mu}s$ pulse width) and 130 kW, respectively. In this paper, we present a system overview and initial design results of the high power pulse transformer.

• Journal of the Korean earth science society
• /
• v.43 no.2
• /
• pp.239-252
• /
• 2022

Quality control methods for the first G-band vapor radiometer (GVR) mounted on a weather aircraft in Korea were developed using the GVR Precipitable Water Vapor (PWV). The aircraft attitude information (degree of pitch and roll) was applied to quality control to select the shortest vertical path of the GVR beam. In addition, quality control was applied to remove a GVR PWV ≥20 mm. It was found that the difference between the warm load average power and sky load average power converged to near 0 when the GVR PWV increased to 20 mm or higher. This could be due to the high brightness temperature of the substratus and mesoclouds, which was confirmed by the Communication, Ocean and Meteorological Satellite (COMS) data (cloud type, cloud top height, and cloud amount), cloud combination probe (CCP), and precipitation imaging probe (PIP). The GVR PWV before and after the application of quality control on a cloudy day was quantitatively compared with that of a local data assimilation and prediction system (LDAPS). The Root Mean Square Difference (RMSD) decreased from 2.9 to 1.8 mm and the RMSD with Korea Local Analysis and Precipitation System (KLAPS) decreased from 5.4 to 4.3 mm, showing improved accuracy. In addition, the quality control effectiveness of GVR PWV suggested in this study was verified through comparison with the COMS PWV by using the GVR PWV applied with quality control and the dropsonde PWV.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.5 s.335
• /
• pp.13-22
• /
• 2005

IEEE 802.11a is a standard for the high-speed wireless local area network (WLAN), supporting from 6 up to 54 Mbps in a 5 GHz band. We propose a channel equalization algerian and a sampling clock recovery algorithm by utilizing the Viterbi decoder output of the IEEE 802.11a WLAN standard. The proposed channel equalizer adaptively compensates channel variations. The proposed system uses re-encoded Viterbi decoder outputs as reference symbols for the adaptation of the channel equalizer. It also extracts sampling phase information with the Viterbi decoder outputs for fine adjustment of the sampling clock. The proposed sampling clock recovery and equalizer are more robust to noise and frequency selective fading environments than conventional systems using only four pilot samples.

• Journal of electromagnetic engineering and science
• /
• v.5 no.1
• /
• pp.8-13
• /
• 2005

The InGaP/GaAs hetero-junction bipolar transistor(HBT) monolithic voltage-controlled dielectric resonator oscillator(VCDRO) is first demonstrated for a Ku-band low noise block down-converter(LNB) system. The on-chip voltage control oscillator core employing base-collector(B-C) junction diodes is proposed for simpler frequency tuning and easy fabrication instead of the general off-chip varactor diodes. The fabricated VCDRO achieves a high output power of 6.45 to 5.31 dBm and a wide frequency tuning range of ]65 MHz( 1.53 $\%$) with a low phase noise of below -95dBc/Hz at 100 kHz offset and -115 dBc/Hz at ] MHz offset. A]so, the InGaP/GaAs HBT monolithic DRO with the same topology as the proposed VCDRO is fabricated to verify that the intrinsic low l/f noise of the HBT and the high Q of the DR contribute to the low phase noise performance. The fabricated DRO exhibits an output power of 1.33 dBm, and an extremely low phase noise of -109 dBc/Hz at 100 kHz and -131 dBc/Hz at ] MHz offset from the 10.75 GHz oscillation frequency.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.5
• /
• pp.225-230
• /
• 2013

This paper presents a novel shunt radio frequency microelectromechanical system switch on a quartz substrate with stiff ribs around the membrane. The buckling effects in the switch membrane and stiction problem are the primary concerns with RF MEMS switches. These effects can be reduced by the proposed design approach due to the stiffness of the ribs around the membrane. A lower mass of the beam and a reduction in the squeeze film damping is achieved due to the slots and holes in the membrane, which further aid in attaining high switching speeds. The proposed switch is optimized to operate in the k-band, which results in a high isolation of -40 dB and low insertion loss of -0.047 dB at 21 GHz, with a low actuation voltage of only 14.6 V needed for the operation the switch. The membrane does not bend with this membrane design approach. Finite element modeling is used to analyze the stress and pull-in voltage.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1942_1943
• /
• 2009

무선통신 시스템의 소형화와 저가격, 고품질, 다기능 재료 및 첨단 가공 기술과 연계된 필터설계 및 제작 기술에 대한 연구가 활발히 진행 중이다. 그러나 무선통신 시스템은 주파수라는 한정된 자원을 사용하기 때문에 주파수 자원의 효율적 관리를 위한 규제나 방안이 필요하고. 이에 따라서 여러 가지 대책과 방안이 필요로 하고 있다. 그래서 필터의 성능개선을 위한 연구가 본질 적으로 중요하게 되었다. 본 논문은 체비세프(Chebyshev)필터와 버터워스(Butterworth)필터를 이용한 대역통과(band pass) 필터를 제안한다. 이 필터는 안정화된 통과대역과 빠른 주파수 응답을 얻기위해 6차 체비세프필터와 8차 버터워스필터를 결합 하였다. 측정된 대역통과 필터는, 차단 영역을 구분하는 스커트(skirt)특성은 날카롭게(sharp) 되었고 통과대역의 평탄도 또한 개선되어짐을 볼 수 있다. 제안된 필터의 중심주파수는 2.5GHz, 대역폭은 200MHz이고, 대역내 평탄도는 0.5dB, 경사도는 오차가 60dB일때 체비세프는 210MHz, 버터워스는 340MHz, 체비세프-버터워스는 290MHz가 되어 버터워스 보다 좋게 되었으며 극점의 배치도 안정적인 결과를 얻었다.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.58-62
• /
• 1999

We fabricated a new hairpin type HTS 2-pole microstrip Bandpass filter to operate at 5.8GHz. The fabrication method was pulsed laser deposition and YBCO films were deposited on ${\alpha}$-A1$_2O_3$ substrates with a CeO$_2$ thin layer as a buffer layer. We developed a new style hairpin type filter by using interdigitide innerpole. Compared to the saute size regular hairpin type filters, our filter had a lower center frequency, bandwidth and loss by an amount of 14.5%, 29.6%, 0.5488dB, respectively. The size of the filters were 13.7${\times}$3.3mm. We did simulations on the several types of band pass filters by using HFSS and serenade. We measured growth rate and Tc of YBCO films grown on CeO$_2$/ ${\alpha}$-A1$_2O_3$ substrates which were rotated while growing films.