• Title/Summary/Keyword: 5세대 이동통신

Search Result 231, Processing Time 0.031 seconds

Adaptive Modulation and Coding of MIMO in Next Generation Mobile Systems (차세대 MIMO 이동통신에서 적응변조시스템의 성능분석)

  • Kang Sung-Jin;Jang Tae-Won;You Young-Whan;Whang In-Tae;Kang Min-Goo;Kang Chang-Eon
    • Journal of Internet Computing and Services
    • /
    • v.4 no.5
    • /
    • pp.1-9
    • /
    • 2003
  • In this paper, we combine AMC (Adaptive Modulation and Coding) with MIMO (Multiple Input Multiple Output) multiplexing to improve the throughput performance of AMC in Next Generation Communication Mobile Systems. In addition, we propose a system that adopts STD (Selection Transmit Diversity) in the combined system. The received SNR (Signal to Noise Ratio) is improved by adopting STD techniques and an improved SNR increases a probability of selecting MCS (Modulation and Coding Scheme) level that supports higher data rate. The computer simulation is performed in flat Rayleigh fading channel. The results show that higher throughput is achieved by AMC-TD schemes. AMC-STTD scheme shows about 250kbps increase in throughput. And AMC-STD with 2 transmit antennas achieves about 420 kbps throughput improvement over the conventional AMC at 9dB SNR.

  • PDF

Optimal Interference Rejection Weight for Multistage Parallel Nulling-Partial PIC Receiver for MIMO MC-CDMA Systems (MIMO MC-CDMA 시스템을 위한 다단계 병렬 널링 및 부분 간섭 제거 수신기를 위한 최적 가중치 결정)

  • 구정회;김경연;심세준;이충용
    • Journal of the Institute of Electronics Engineers of Korea TC
    • /
    • v.41 no.11
    • /
    • pp.9-15
    • /
    • 2004
  • We propose optimal interference rejection weight for multistage parallel nulling (MPN) partial parallel interference cancellation (PPIC) receiver previously proposed to enhance the performance of V-BLAST for downlink multiple-input multiple-output (MIMO) multicarrier (MC)-code division multiple access (CDMA) systems. MPN-PPIC method proposed in [1] was based on the parallel interference cancellation (PIC) with fixed interference rejection weight obtained experimentally. However, the fixed weight can not be adapted to various systems efficiently, thus we proposed method for the optimal interference rejection weight based on the received signal to interference and noise ratio (SINR), and the performance of the proposed method was evaluated through computer simulation comparing with the previous method. We obtained performance gains of 2.5 dB ~ 5 dB for BER of 10$^{-3}$ .

Effects of Launching Vehicle's Velocity on the Performance of FTS Receiver (발사체의 속도가 FTS 수신기의 성능에 미치는 영향)

  • Kang, Sanggee
    • Journal of Satellite, Information and Communications
    • /
    • v.9 no.3
    • /
    • pp.27-32
    • /
    • 2014
  • A doppler shift is generated by moving a transmitter or receiver operated in communication systems. The doppler frequency shift between a transmitter and a receiver or the frequency offset present in transceivers must be removed to get the wanted system performance. FTS is used for preventing an accident from operating abnormally and for guaranteeing public protection. A launching vehicle's initial velocity is very fast in order to escape the earth and the amount of doppler shift is large. Recently many studies to adopt the next generation FTS are ongoing. To introduce new FTS, the effects of doppler shift on the performance of the new FTS must be studied. In this paper the doppler effect caused by launching vehicle's velocity affecting the performance of FTS receiver is investigated into two cases, one is for EFTS as a digital FTS and the other is for FTS using a tone signal. Noncoherent DPSK and noncoherent CPFSK are considered as the modulation methods of EFTS. In the cases of the doppler frequency shift of 200Hz present in EFTS using noncoherent DPSK and noncoherent CPFSK are simulated. Simulation results show that $E_b/N_o$ of 0.5dB deteriorates in the region of near BER of about $10^{-5}$ in RS coding. And there is no performance variation in $E_b/N_o$ or $E_b/N_o$ is worsened about 0.1dB in the same BER region for the case of using convolutional and BCH coding. Quadrature detector used in FTS using tone signals is not influenced by the doppler frequency shift.

Multi-User X-Channel Interference Alignment in 5 Generation MIMO Mobile Communications (5세대 MIMO 이동 통신의 다중 사용자 X 채널 간섭 정렬)

  • Kim, Jeong-Su;Lee, Moon Ho
    • The Journal of the Institute of Internet, Broadcasting and Communication
    • /
    • v.17 no.5
    • /
    • pp.61-69
    • /
    • 2017
  • The study on interference channel is very important information theoretically and many studies have been done on it. However, even in the simplest case, even in the case of two user interfering channels, the channel capacity is not yet known except in special cases. Recently, research on the multiplexing gain that shows the tendency of the transmission rate in the high signal to noise ratio (SNR) band has been actively carried out, instead of accurately grasping the channel capacity. Obtaining optimal multiplexing gain can reveal trends in channel capacity at high signal-to-noise ratio bands. In an interfering channel with two users, the best multiplexing gain can be obtained by eliminating the interference. However, recent research shows that when the number of users is more than three, the optimal multiplexing gain can not be obtained only by zero forcing and a new technique called interference sorting is needed. There are two types of interference sorting techniques. Beamforming A method of effectively separating signals and interference by properly selecting matrices and constructing structured codes using rational numbers and irrational numbers. The interference alignment technique can achieve optimal multiplexing gain in various environments such as interference channel, X channel, compound broadcast channel, and multi hop network for multi source multi destination. In recent years, it has also been applied to distributed storage. Lee et al., "Lattice Code Interference Alignment in Cooperative Multipoint Transmission (COMP) for Interference Channels of Three Users", Journal of the Institute of Electronics Engineers, vol.49-TC,no.6,2012. In this paper, the DoF of delayed channel information is obtained.

Edge to Edge Model and Delay Performance Evaluation for Autonomous Driving (자율 주행을 위한 Edge to Edge 모델 및 지연 성능 평가)

  • Cho, Moon Ki;Bae, Kyoung Yul
    • Journal of Intelligence and Information Systems
    • /
    • v.27 no.1
    • /
    • pp.191-207
    • /
    • 2021
  • Up to this day, mobile communications have evolved rapidly over the decades, mainly focusing on speed-up to meet the growing data demands of 2G to 5G. And with the start of the 5G era, efforts are being made to provide such various services to customers, as IoT, V2X, robots, artificial intelligence, augmented virtual reality, and smart cities, which are expected to change the environment of our lives and industries as a whole. In a bid to provide those services, on top of high speed data, reduced latency and reliability are critical for real-time services. Thus, 5G has paved the way for service delivery through maximum speed of 20Gbps, a delay of 1ms, and a connecting device of 106/㎢ In particular, in intelligent traffic control systems and services using various vehicle-based Vehicle to X (V2X), such as traffic control, in addition to high-speed data speed, reduction of delay and reliability for real-time services are very important. 5G communication uses high frequencies of 3.5Ghz and 28Ghz. These high-frequency waves can go with high-speed thanks to their straightness while their short wavelength and small diffraction angle limit their reach to distance and prevent them from penetrating walls, causing restrictions on their use indoors. Therefore, under existing networks it's difficult to overcome these constraints. The underlying centralized SDN also has a limited capability in offering delay-sensitive services because communication with many nodes creates overload in its processing. Basically, SDN, which means a structure that separates signals from the control plane from packets in the data plane, requires control of the delay-related tree structure available in the event of an emergency during autonomous driving. In these scenarios, the network architecture that handles in-vehicle information is a major variable of delay. Since SDNs in general centralized structures are difficult to meet the desired delay level, studies on the optimal size of SDNs for information processing should be conducted. Thus, SDNs need to be separated on a certain scale and construct a new type of network, which can efficiently respond to dynamically changing traffic and provide high-quality, flexible services. Moreover, the structure of these networks is closely related to ultra-low latency, high confidence, and hyper-connectivity and should be based on a new form of split SDN rather than an existing centralized SDN structure, even in the case of the worst condition. And in these SDN structural networks, where automobiles pass through small 5G cells very quickly, the information change cycle, round trip delay (RTD), and the data processing time of SDN are highly correlated with the delay. Of these, RDT is not a significant factor because it has sufficient speed and less than 1 ms of delay, but the information change cycle and data processing time of SDN are factors that greatly affect the delay. Especially, in an emergency of self-driving environment linked to an ITS(Intelligent Traffic System) that requires low latency and high reliability, information should be transmitted and processed very quickly. That is a case in point where delay plays a very sensitive role. In this paper, we study the SDN architecture in emergencies during autonomous driving and conduct analysis through simulation of the correlation with the cell layer in which the vehicle should request relevant information according to the information flow. For simulation: As the Data Rate of 5G is high enough, we can assume the information for neighbor vehicle support to the car without errors. Furthermore, we assumed 5G small cells within 50 ~ 250 m in cell radius, and the maximum speed of the vehicle was considered as a 30km ~ 200 km/hour in order to examine the network architecture to minimize the delay.

CPW-Fed Super-wideband Semicircular-Disc-Shaped Dipole Antenna (CPW-급전 초광대역 반원-디스크-모양 다이폴 안테나)

  • Junho Yeo;Jong-Ig Lee
    • Journal of Advanced Navigation Technology
    • /
    • v.28 no.3
    • /
    • pp.356-361
    • /
    • 2024
  • This paper deals with the design and fabrication of a coplanar waveguide (CPW)-fed super-wideband semicircular-disk-shaped dipole antenna operating in a frequency band of 2.4 GHz or higher. To feed the antenna, a CPW feed line was appended to the center of the lower arm of the semicircular-disk-shaped dipole antenna. For miniaturization, square patches were added to the ends of the two arms of the semicircular-disk-shaped dipole, whereas the slot width of the CPW feed line at the center of the dipole antenna was increased to improve impedance matching in the 5.4-6.3 GHz band. The simulated frequency band of the proposed antenna for a voltage standing wave ratio (VSWR) less than 2 was 2.369-30 GHz(170.7%), whereas the fabricated antenna was maintained VSWR less than 2 in the frequency range of 2.378-20 GHz when measured using a network analyzer operating up to 20 GHz so it can be applied as a super-wideband antenna for next-generation mobile communications.

An Implementation of Dynamic Gesture Recognizer Based on WPS and Data Glove (WPS와 장갑 장치 기반의 동적 제스처 인식기의 구현)

  • Kim, Jung-Hyun;Roh, Yong-Wan;Hong, Kwang-Seok
    • The KIPS Transactions:PartB
    • /
    • v.13B no.5 s.108
    • /
    • pp.561-568
    • /
    • 2006
  • WPS(Wearable Personal Station) for next generation PC can define as a core terminal of 'Ubiquitous Computing' that include information processing and network function and overcome spatial limitation in acquisition of new information. As a way to acquire significant dynamic gesture data of user from haptic devices, traditional gesture recognizer based on desktop-PC using wire communication module has several restrictions such as conditionality on space, complexity between transmission mediums(cable elements), limitation of motion and incommodiousness on use. Accordingly, in this paper, in order to overcome these problems, we implement hand gesture recognition system using fuzzy algorithm and neural network for Post PC(the embedded-ubiquitous environment using blue-tooth module and WPS). Also, we propose most efficient and reasonable hand gesture recognition interface for Post PC through evaluation and analysis of performance about each gesture recognition system. The proposed gesture recognition system consists of three modules: 1) gesture input module that processes motion of dynamic hand to input data 2) Relational Database Management System(hereafter, RDBMS) module to segment significant gestures from input data and 3) 2 each different recognition modulo: fuzzy max-min and neural network recognition module to recognize significant gesture of continuous / dynamic gestures. Experimental result shows the average recognition rate of 98.8% in fuzzy min-nin module and 96.7% in neural network recognition module about significantly dynamic gestures.

Design and Implementation of Receiver's Buffer Model for Stably Receiving a Hierarchically Encoded UHD Content Based on MMT (MMT 기반 계층 부호화된 UHD 콘텐츠의 안정적인 수신을 위한 수신 버퍼 모델 설계 및 구현)

  • Song, SeulKi;Bang, JongHo;Paik, JongHo
    • Journal of Broadcast Engineering
    • /
    • v.22 no.5
    • /
    • pp.570-577
    • /
    • 2017
  • Recently, with the development of broadcasting communication, users expect to receive high quality and various broadcasting services anytime, anywhere. In the case of terrestrial broadcasting, HD broadcasting and mobile broadcasting are provided at different frequencies. In the case of terrestrial UHD, which recently started trial broadcasting, 700MHz frequency is used which is different from the existing one. If the contents of the same contents are transmitted at different frequencies, it can be considered ineffective in terms of the use efficiency of the terrestrial broadcast frequency. As a method to solve this problem, a transmission system model and a service have been proposed for transmitting the hierarchical encoded UHD contents by SHVC on the basis of the multimedia transmission technology MMT in a heterogeneous network environment combining broadcast network and communication network. However, it is still in the initial stage of study the receiving model that can reliably receive various quality UHD contents in various environments such as mobile and fixed environment. Therefore, in this paper, we propose a receive buffer model that can reliably receive UHD contents layered on SHVC based on MMT.

Development of Digital Transceiver Unit for 5G Optical Repeater (5G 광중계기 구동을 위한 디지털 송수신 유닛 설계)

  • Min, Kyoung-Ok;Lee, Seung-Ho
    • Journal of IKEEE
    • /
    • v.25 no.1
    • /
    • pp.156-167
    • /
    • 2021
  • In this paper, we propose a digital transceiver unit design for in-building of 5G optical repeaters that extends the coverage of 5G mobile communication network services and connects to a stable wireless network in a building. The digital transceiver unit for driving the proposed 5G optical repeater is composed of 4 blocks: a signal processing unit, an RF transceiver unit, an optical input/output unit, and a clock generation unit. The signal processing unit plays an important role, such as a combination of a basic operation of the CPRI interface, a 4-channel antenna signal, and response to external control commands. It also transmits and receives high-quality IQ data through the JESD204B interface. CFR and DPD blocks operate to protect the power amplifier. The RF transmitter/receiver converts the RF signal received from the antenna to AD, is transmitted to the signal processing unit through the JESD204B interface, and DA converts the digital signal transmitted from the signal processing unit to the JESD204B interface and transmits the RF signal to the antenna. The optical input/output unit converts an electric signal into an optical signal and transmits it, and converts the optical signal into an electric signal and receives it. The clock generator suppresses jitter of the synchronous clock supplied from the CPRI interface of the optical input/output unit, and supplies a stable synchronous clock to the signal processing unit and the RF transceiver. Before CPRI connection, a local clock is supplied to operate in a CPRI connection ready state. XCZU9CG-2FFVC900I of Xilinx's MPSoC series was used to evaluate the accuracy of the digital transceiver unit for driving the 5G optical repeater proposed in this paper, and Vivado 2018.3 was used as the design tool. The 5G optical repeater digital transceiver unit proposed in this paper converts the 5G RF signal input to the ADC into digital and transmits it to the JIG through CPRI and outputs the downlink data signal received from the JIG through the CPRI to the DAC. And evaluated the performance. The experimental results showed that flatness, Return Loss, Channel Power, ACLR, EVM, Frequency Error, etc. exceeded the target set value.

A 14b 100MS/s $3.4mm^2$ 145mW 0.18um CMOS Pipeline A/D Converter (14b 100MS/s $3.4mm^2$ 145mW 0.18un CMOS 파이프라인 A/D 변환기)

  • Kim Young-Ju;Park Yong-Hyun;Yoo Si-Wook;Kim Yong-Woo;Lee Seung-Hoon
    • Journal of the Institute of Electronics Engineers of Korea SD
    • /
    • v.43 no.5 s.347
    • /
    • pp.54-63
    • /
    • 2006
  • This work proposes a 14b 100MS/s 0.18um CMOS ADC with optimized resolution, conversion speed, die area, and power dissipation to obtain the performance required in the fourth-generation mobile communication systems. The 3-stage pipeline ADC, whose optimized architecture is analyzed and verified with behavioral model simulations, employs a wide-band low-noise SHA to achieve a 14b level ENOB at the Nyquist input frequency, 3-D fully symmetric layout techniques to minimize capacitor mismatch in two MDACs, and a back-end 6b flash ADC based on open-loop offset sampling and interpolation to obtain 6b accuracy and small chip area at 100MS/s. The prototype ADC implemented in a 0.18um CMOS process shows the measured DNL and INL of maximum 1.03LSB and 5.47LSB, respectively. The ADC demonstrates a maximum SNDR and SFDR of 59dB and 72dB, respectively, and a power consumption of 145mW at 100MS/s and 1.8V. The occupied active die area is $3.4mm^2$.