• JSTS:Journal of Semiconductor Technology and Science
• /
• 제15권2호
• /
• pp.276-279
• /
• 2015

This paper presents two 3-stage D-band stacked amplifiers developed in a $0.13-{\mu}m$ SiGe BiCMOS technology, employed to compare the conventional cascode topology and the common-base (CB)/CB stacked topology. AMP1 employs two cascode stages followed by a CB/CB stacked stage, while AMP2 is composed of three CB/CB stacked stages. AMP1 showed a 17.1 dB peak gain at 143.8 GHz and a saturation output power of -4.2 dBm, while AMP2 showed a 20.4 dB peak gain at 150.6 GHz and a saturation output power of -1.3 dBm. The respective power dissipation was 42.9 mW and 59.4 mW for the two amplifiers. The results show that CB/CB stacked topology is favored over cascode topology in terms of gain near 140 GHz.

• 마이크로전자및패키징학회지
• /
• 제21권3호
• /
• pp.63-66
• /
• 2014

본 연구에서는 3차원 적층 집적회로 구조에서 Cu TSV를 활용한 열관리 가능성에 대해 살펴보았다. Cu TSV가 있는 실리콘 웨이퍼와 일반 실리콘 웨이퍼 후면부를 점열원을 이용하여 가열한 후 전면부의 온도 변화를 적외선 현미경을 이용하여 관찰하였다. 일반 실리콘 웨이퍼의 경우 두께가 얇아지면서 국부적인 고온영역이 관찰됨으로서 적층 구조에서 층간 열문제의 가능성을 확인할 수 있었다. TSV 웨이퍼의 경우 일반 실리콘 웨이퍼보다 넓은 영역의 고온 분포를 나타내었으며, 이는 Cu TSV를 통한 우선적인 열전달로 인한 것으로 적층 구조에서 Cu TSV를 이용한 효과적인 열관리의 가능성을 나타낸다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제12권2호
• /
• pp.139-149
• /
• 2012

A 3D stacked IC is made by multiple dies (possibly) with heterogeneous process technologies. Therefore, die-to-die variation in 2D chips renders on-package variation (OPV) in a 3D chip. In spite of the different variation effect in 3D chips, generally, 3D die stacking can produce high yield due to the smaller individual die area and the averaging effect of variation on data path. However, 3D clock network can experience unintended huge clock skew due to the different clock propagation routes on multiple stacked dies. In this paper, we analyze the on-package variation effect on 3D clock networks and show the necessity of a post silicon management method such as body biasing technique for the OPV induced 3D clock skew control in 3D stacked IC designs. Then, we present a parametric yield improvement method to mitigate the OPV induced 3D clock skew.

• 한국재료학회지
• /
• 제17권7호
• /
• pp.347-351
• /
• 2007

Vertical interconnect technology called 3D stacking has been a major focus of the next generation of IC industries. 3D stacked devices in the vertical dimension give several important advantages over conventional two-dimensional scaling. The most eminent advantage is its performance improvement. Vertical device stacking enhances a performance such as inter-die bandwidth improvements, RC delay mitigation and geometrical routing and placement advantages. At present memory stacking options are of great interest to many industries and research institutes. However, these options are more focused on a form factor reduction rather than the high performance improvements. In order to improve a stacked device performance significantly vertical interconnect technology with wafer level stacking needs to be much more progressed with reduction in inter-wafer pitch and increases in the number of stacked layers. Even though 3D wafer level stacking technology offers many opportunities both in the short term and long term, the full performance benefits of 3D wafer level stacking require technological developments beyond simply the wafer stacking technology itself.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권5호
• /
• pp.566-571
• /
• 2014

Channel-stacked 3D NAND flash memory is very promising candidate for the next-generation NAND flash memory. However, there is an inherent issue on cell size variation between stacked channels due to the declined etch slope. In this paper, the effect of the cell variation on the incremental step pulse programming (ISPP) characteristics is studied with 3D TCAD simulation. The ISPP slope degradation of elliptical channel is investigated. To solve that problem, a new programming method is proposed, and we can alleviate the $V_T$ variation among cells and reduce the total programming time.

• 전기전자학회논문지
• /
• 제20권3호
• /
• pp.279-284
• /
• 2016

This paper presents a two stage L-band power amplifier realized with a $0.32{\mu}m$ Silicon-On-Insulator (SOI) CMOS technology. To overcome a low breakdown voltage limit of MOSFET, stacked-FET structures are employed, where three transistors in the first stage amplifier and four transistors in the second stage amplifier are connected in series so that their output voltage swings are added in phase. The stacked-FET structures enable the proposed amplifier to achieve a 21.5 dB small-signal gain and 15.7 dBm output 1-dB compression power at 1.9 GHz with a 122 mA DC current from a 4 V supply. The amplifier delivers a 19.7 dBm. This paper presents a two stage L-band power amplifier realized with a $0.32{\mu}m$ Silicon-On-Insulator (SOI) CMOS technology. To overcome a low breakdown voltage limit of MOSFET, stacked-FET structures are employed, where three transistors in the first stage amplifier and four transistors in the second stage amplifier are connected in series so that their output voltage swings are added in phase. The stacked-FET structures enable the proposed amplifier to achieve a 21.5 dB small-signal gain and 15.7 dBm output 1-dB compression power at 1.9 GHz with a 122 mA DC current from a 4 V supply. The amplifier delivers a 19.7 dBm saturated output power with a 16 % maximum Power Added Efficiency (PAE). A bond wire fine tuning technology enables the amplifier a 23.67 dBm saturated output power with a 20.4 % maximum PAE. The die area is $1.9mm{\times}0.6mm$.

• 마이크로전자및패키징학회지
• /
• 제22권2호
• /
• pp.5-9
• /
• 2015

3차원 적층 반도체에서의 열관리를 위한 연구 동향에 대해서 살펴보았다. 적층 구조는 평면구조와 달리 단위 패키지당 발열량 증가, 단위 바닥면적당 전력 소비량 증가, 이웃 칩의 영향으로 과열 가능성의 증가, 냉각구조 추가의 어려움, 국부 열원의 발달 등으로 발열 문제가 매우 심각해질 수 있으며, 특히 국부 열원은 적층을 위해 칩 두께가 얇아짐으로 더욱 심화되고 있어 이를 고려한 발열관리가 필요하다. 구리 TSV는 높은 열전도도를 이용하여 열원의 열을 효과적으로 주변으로 배출하는 역할을 하며 범프 및 gap 충진 재료, 적층 순서와 함께 적층 반도체의 열확산에 큰 영향을 미친다. 이는 실험으로나 수치해석으로 확인되고 있으며, 향후 적층 구조의 각 구성 요소들의 열 특성을 반영한 회로 설계가 이루어질 것으로 예상된다.

• Journal of information and communication convergence engineering
• /
• 제14권1호
• /
• pp.40-44
• /
• 2016

The device coupling between the stacked top/bottom field-effect transistors (FETs) in two types of monolithic 3D inverter (M3INV) with/without a metal layer in the bottom tier is investigated, and then the regime of the thickness T_ILD and dielectric constant ε_r of the inter-layer distance (ILD), the doping concentration N_d (N_a), and length L_g of the channel, and the side-wall length L_SW where the stacked FETs are coupled are studied. When N_d (N_a) < 10¹⁶ cm^-3 and L_SW < 20 nm, the threshold voltage shift of the top FET varies almost constantly by the gate voltage of the bottom FET, but when N_d (N_a) > 10¹⁶ cm^-3 or L_SW > 20 nm, the shift decreases and increases, respectively. M3INVs with T_ILD ≥ 50 nm and ε_r ≤ 3.9 can neglect the interaction between the stacked FETs, but when T_ILD or ε_r do not meet the above conditions, the interaction must be taken into consideration.

• 반도체디스플레이기술학회지
• /
• 제17권4호
• /
• pp.86-90
• /
• 2018

Standards related to express the non-flatness of a wafer are reviewed and discussed, for example, bow, warp, and sori. Novel wafer warpage measurement method is proposed for 3D stacked IC application. The new way measures heat transfer from a heater to a wafer, which is a function of the contact area between these two surfaces and in turn, this contact area depends on the wafer warpage. Measurement options such as heating from room temperature and cooling from high temperature were experimentally examined. The heating method was found to be sensitive to environmental conditions. The cooling technique showed more robust and repeatable results and the further investigation for the optimal cooling condition is underway.

• Journal of electromagnetic engineering and science
• /
• 제11권4호
• /
• pp.282-289
• /
• 2011

GHz electromagnetic interference (EMI) characteristics are analyzed for a 3dimensional (3D) stacked chip power distribution network (PDN) with through silicon via (TSV) connections. The EMI problem is mostly raised by P/G (power/ground) noise due to high switching current magnitudes and high PDN impedances. The 3D stacked chip PDN is decomposed into P/G TSVs and vertically stacked capacitive chip PDNs. The TSV inductances combine with the chip PDN capacitances produce resonances and increase the PDN impedance level in the GHz frequency range. These effects depend on stacking configurations and P/G TSV designs and are analyzed using the P/G TSV model and chip PDN model. When a small size chip PDN and a large size chip PDN are stacked, the small one's impedance is more seriously affected by TSV effects and shows higher levels. As a P/G TSV location is moved to a corner of the chip PDNs, larger PDN impedances appear. When P/G TSV numbers are enlarged, the TSV effects push the resonances to a higher frequency range. As a small size chip PDN is located closer to the center of a large size chip PDN, the TSV effects are enhanced.