• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.10
• /
• pp.94-105
• /
• 2020

Recently, most studies of 3D printing in construction have focused on the development of 3D printers and materials suitable for construction 3D printers. In comparison, there has been little research on design support tools that enable representative BIM data of building modeling tools to be applied to 3D printing. In addition, existing 3D printing slicing programs are commercialized around manufacturing, showing that they are unsuitable for construction 3D printing. Therefore, this research aims to develop a design support tool for 3D printing for buildings. The developed design support tool was validated based on arbitrary BIM data. Verification showed that wall pattern generation was modeled accurately without errors, and a calculation of the construction period showed that the formula presented in this study was valid. Furthermore, the maximum length of the mesh split was set to 100mm to minimize errors when converting to STL files.

• Journal of the Korea Convergence Society
• /
• v.12 no.12
• /
• pp.169-176
• /
• 2021

This study aims to explore the formativeness of 3D printed parametric fashion products while parametric design-based 3D printed fashion products are increasing. As a research method, theoretical review was conducted and formative properties of 3D printing parametric fashion products were derived, and cases of 3D printing parametric fashion products were collected and examined into three types of clothing, shoes, and accessories. As a result of the study, it was possible to confirm the shape with the motif of a natural object, and structurally, the economical optimal structure, assembly structure, and natural structure were confirmed. was found to use natural and achromatic colors. Through the understanding of the formativeness of 3D printing parametric fashion products presented in this study, it is expected that it will be used as basic data to understand the spread and formative flow of parametric-based fashion products.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.2
• /
• pp.101-111
• /
• 2004

In order to guarantee the stability of a tunnel and its optimum design, it is very important to obtain enough ground investigation data. In realty, however, it is not the case due to the limitation of measuring spatially distributed data and economical reasons. Especially, there are regions where drilling is impossible due to civil appeal and mountainous topology, and it is also difficult to estimate rock mass classes quantitatively with only geophysical exploration data. In this study, therefore, 3 dimensional multiple indicator kriging (3D-MI kriging), which can incorporate geophysical exploration data and drill core data off a tunnel center line, is proposed to cope with such problems. To this end, two dimensional mutiple indicator kriging, which is one of the geostatistical techniques, is extended for three dimensional analysis. Also, the proposed 3D-MI kriging was applied to determine the rock mass classes by RMR system for the design of a Kyungbu express rail way tunnel.

• Journal of the Ergonomics Society of Korea
• /
• v.25 no.2
• /
• pp.85-94
• /
• 2006

The purpose of this study is to extract typical body shapes of Korean adults based on the three-dimensional Korean anthropometric data measured through 5th national anthropometric survey and to examine the suitability of the 3-D human shape data for the interior packaging. 36 three-dimensional anthropometric variables related to the design of vehicle interior were considered for the appraisal of typical body shapes. Four major factors were extracted by the factor analysis and factor scores were calculated for all subjects. Typical or standard drivers of Korean adults were selected by the minimum deviation criteria for the four factor scores with respect to 5th, 50th, and 95th percentiles, respectively. Typical drivers of Korean adults were visualized by the CATIA-HUMAN program due to the absence of proper application software for three-dimensionally scanned human body data. There are considerable differences between the anthropometric data of Korean adults and those provided by CATIA-HUMAN program, which shows that the modeling data provided by CATIA-HUMAN should not be directly applied to the ergonomic evaluation for the vehicle design. This suggests the necessity for the development of suitable software for scanned human shape data. It is also expected that the anthropometric data of typical drivers extracted from this study help design package layouts and improve the suitability of ergonomic evaluation for Korean customers.

• International Journal of Contents
• /
• v.5 no.3
• /
• pp.19-23
• /
• 2009

Laser scanning technology is a maturing measurement technology which is capable of obtaining 3D measurement data of objects with high-accuracy, high-resolution and in a short time. Laser scanners are used more and more as surveying instruments for various applications. This paper describes the procedure of 3D data acquirement using terrestrial LiDAR and section drawing extraction through a series of processing for remodeling the interior of a department building. Accurate drawings are needed for improvement construction of building interior. However if the design drawings of that time of construction work were lost or damaged or actual dimensions of drawings differ from those of design drawings, the interior should be resurveyed. In this study, the extraction process of interior plane figures were suggested through using laser scanning and related reverse engineering software

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.1
• /
• pp.6-14
• /
• 2012

For integrated complementary metal oxide semiconductor (CMOS) circuits, the lateral spread for two-dimensional (2-D) impurity distributions are very important for the analyzing the devices. The measured two-dimensional SEM data obtained using the chemical etching-method matched very well with the results of the Gauss model for boron implanted samples. But the profiles in boron implanted silicon were deviated from the Gauss model. The profiles in boron implanted silicon were shown a little bit steep profile in the deep region due to backscattering effect on the near surface from the bombardments of light boron ions. From the simulated 3-D data obtained using an analytical model, the 1-D and 2-D data were compared with the experimental data and could be verified the justification from the experimental data. The data of 3-D model were also shown good agreements with the experimental and the simulated data. It can be used in the 3-D chip design and the analysis of microelectro-mecanical system (MEMS) and special devices.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.850-853
• /
• 2004

The development of 3D CAM system for the manufacturing of end mills becomes a key approach to save the time and reduce cost for end mills manufacturing. This paper presents the calculation and simulation of end mill tools CNC machining bases on 5-axes CNC grinding machine tool. In this study describes the process of generation and simulation of grinding point data between the tool and the grinding wheels through the machined time. Depend on input data of end mill geometry, wheels geometry, wheel setting, machine setting the end mill configuration and NC code for machining will be generated and visualized in 3 dimension before machining. The 3D visualizations of end mill manufacturing was generated by using OpenGL in C++. The development software was designed by using Microsoft Visual C++, which has many advantages for users, saving time and reducing manufacturing cost.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.7
• /
• pp.861-868
• /
• 2021

With the development of technology for visualizing big-data, tasks such as intuitively analyzing a lot of data, detecting errors, and deriving meaning are actively progressing. In this paper, we describe the design and implementation of a 3D analysis that collects and stores the writing data in Chinese characters provided by the Korean Classical Database of the Korean Classics Translation Institute, stores and progress the data, and visualizes the writing information in a 3D network diagram. It solves the problem when a large amount of data is expressed in 2D, intuitive that analysis, error detection, meaningful data extraction such as characteristics, similarity, differences, etc. and user convenience can be provided. In this paper, we improved the problems of analyzing Chosun dynasty poetry in Chinese characters using 2D visualization conducted in previous studies.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.46 no.4
• /
• pp.657-671
• /
• 2022

This study aims to develop three dimensional (3D) yoga knee protectors that provide excellent wearing comfort. Three types of pads were modeled using 3D human data: two types of 3.0-cm-wide pads separated into top and bottom with thicknesses of 0.1 cm (TPU-1: A) and 0.2 cm (TPU-2: B); and one type with three 0.2-cm-thick separated panels (TPU-S: C). Based on these models, five knee protectors were developed using 3D patterning and 3D printing. Types A, B, and C were integrated with 0.6-cm neoprene pads. Type D was fabricated with a donut-shaped 0.6-cm neoprene pad inserted, while Type E consisted of two discrete 0.6-cm neoprene pads embedded in the protector's upper and lower sides. Wearing comfort was evaluated in terms of fit, pressure, and cushioning while in a standing and kneeling position and while in motion. The findings suggest that the fabricated knee protectors were evaluated as comfortable to the individuals with knee pain, rather than those without knee pain. The individuals with knee pain preferred the soft pads made of neoprene positioned around the knee (NEO-S: E), while those without knee pain favored the cushioned pads with a pattern structure maintained by thin 3D-printed pads (TPU-1: A).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1424-1428
• /
• 2005

This paper describes a dedicated three-dimensional CAD system for design of drawing dies for automotive body panels. Since solid die models are useful not only for simulations for design verification, but also for NC tool path generation to machine dies and their Styrofoam patterns, 3-D CAD systems have been introduced in the tooling shop of automotive manufacturers. However, the work to build solid models requires a lot of time and effort if the designer uses only the general modeling capabilities of commercial 3-D CAD systems. To solve this problem, we customized a 3-D CAD system for the drawing die design. The system provides not only 3-D design capabilities, but also standard part libraries to enhance design productivity. By introducing this system, the drawing dies can be designed more rapidly in the 3-D space, and their solid data can be directly transferred to CAM tools for NC tool path generation and simulation tools for virtual manufacturing