• Journal of radiological science and technology
• /
• v.35 no.4
• /
• pp.327-333
• /
• 2012

Purpose: To analyze the correlation between dose volume histograms(DVH) based on organ outer wall contour and organ wall delineation for bladder and rectum, and to compare the doses to these organs with the absorbed doses at the bladder and rectum. Material and methods: Individual CT based brachytherapy treatment planning was performed in 13 patients with cervical cancer as part of a prospective comparative trial. The external contours and the organ walls were delineated for the bladder and rectum in order to compute the corresponding dose volume histograms. The minimum dose in 0.1 $cm^3$, 1 $cm^3$, 2 $cm^3$, 5 $cm^3$, 10 $cm^3$ volumes receiving the highest dose were compared with the absorbed dose at the rectum and bladder reference point. Results: The bladder and rectal doses derived from organ outer wall contour and computed for volumes of 2 $cm^3$, provided a good estimate for the doses computed for the organ wall contour only. This correspondence was no longer true when large volumes were considered. Conclusion: For clinical applications, when volumes smaller than 5 $cm^2$ are considered, the dose-volume histograms computed from external organ contours for the bladder and rectum can be used instead of dose -volume histograms computed for the organ walls only. External organ contours are indeed easier to obtain. The dose at the ICRU rectum reference point provides a good estimate of the rectal dose computed for volumes smaller than 2 $cm^2$ only for a midline position of the rectum. The ICRU bladder reference point provides a good estimate of the dose computed for the bladder wall only in cases of appropriate balloon position.

• Journal of Korean Society of Transportation
• /
• v.17 no.4
• /
• pp.99-110
• /
• 1999

With a growing awareness, transportation is the maior source of urban air pollution. Planners and policy-makers are strongly urged to care the impacts of transportation management strategies on environment. Since transport-related air Pollution can be regarded as negative externalities of transport, it is indispensable to evaluate chanties in air quality which seems to occur when proposed transport measures are implemented. In addition, transport measures should be integrated in a set of combined Paradigm regarding transport and environment. Based on the integrated Paradigm between transportation demand management(TDM) and environmental planning, the main focus is given to apply environment cost internalizing measures to the short-term congestion management Program(SCMP) in Seoul, that has been developed in 1998 by Seoul Development Institute. Three modules are analyzed: without and/or with ￦500, ￦1000 emission plus gas tax, respectively. From the empirical applications on Seoul city, one of the most exemplary findings in SCMP program is that, emission plus gas tax can be a very useful measure to reduce vehicular emissions by targeting major Pollutants differently, rather than by dealing with pollutants collectively. Further research that provides (1)showing the spatial variation of pollution levels along the intersections, (2)more developing combined Paradigm between transport, land use, and environment, (3)using environmental road capacity rather than Physical-aspects of road capacity, and (4)continuing R&D on air quality constrained TDM, can contribute significantly to applications of the real and efficient environment-constrained transportation planning.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.39 no.6
• /
• pp.691-702
• /
• 2019

Flood inundation map has various important roles in terms of municipal planning, timely dam operation, economic levee design, and building flood forecasting systems. Considering that the riparian areas adjacent to national rivers with high potential flood vulnerability conventionally imposed special cares to justify applications of recently available two- or three-dimensional flood inundation numerical models on top of digital elevation models of dense spatial resolution such as LiDAR irrespective of their high costs. On the contrary, local streams usually could not have benefits from recent technological advances, instead they inevitably have relied upon time-consuming manual drawings or have accepted DEMs with poor resolutions or inaccurate 1D numerical models for producing inundation maps due mainly to limited budgets and suitable techniques. In order to efficiently and cost-effectively provide a series of flood inundation maps dedicatedly for the local streams, this study proposed an OpenGIS-based flood mapping tool named Open Flood Mapper (OFM). The spatial accuracy of flood inundation map derived from the OFM was validated throughout comparison with an inundation trace map acquired after typhoon Nari in Hancheon basin located in Jeju Island. Also, a series of inundation maps from the OFM were comprehensively investigated to track the burst of flood in the extreme flood events.

• Herbal Formula Science
• /
• v.18 no.1
• /
• pp.23-42
• /
• 2010

This report describes 90 prescriptions related to the use of Platycodi Radix main blended from Dongeuibogam. The following conclusions were reached through investigations on the prescriptions that use Platycodi Radix as a key component. Prescriptions that Platycodi Radix was taken as a monarch drug are utilized for 30 therapeutic purposes, for example, cough disease, throat disease, abscess and pus, and wind disease. In particular, 12.1% of prescriptions appear in the chapter of cough, and 9.9% of those appear in the chapter of throat, and each 8.8% of those appear in the chapter of abscess and of wind disease. Prescriptions that utilize Platycodi Radix as the main ingredient are used in the treatment of cough disease, throat disease and abscess, and they are also used for treating 74 different types of disease. The prescriptions are compounded with Platycodi Radix as a monarch drug are related to exogenous agents such as wind-cold pathogen, wind-heat pathogen, epidemic diseases, and endogenous agents such as seven emotions, and non-endo-exopathogenic factors like excessive labor, deficiency of Qi and blood, phlegm-mass, phlegm-fire, ect. The dosage of Platycodi Radix is 2pun(about 0.75g) to 1nyang(about 37.5g), however 1don (about 3.75g) has been taken the most for clinical application. We can find out that according to herbs or prescriptions blended with it self, Platycodi Radix makes a variety of functions to penetrate lung stagnancy and remove phlegm, relieve throat pain and get rid of pus, and regulate Qi flow. And Gamgiltang is the most useful base prescription which used the Platycodi Radix as the main component.

• Journal of Radiation Protection and Research
• /
• v.41 no.2
• /
• pp.167-171
• /
• 2016

Background: TlBr is of considerable technological importance for radiation detection applications where detecting high-energy photons such as X-rays and ${\gamma}$-rays are of prime importance. However, there were few reports on investigating optical properties of TlBr itself for deeper understandings of this material and for making better radiation detection devices. Thus, in this paper, we report on the optical characterizations of TlBr single crystals. Spectroscopic ellipsometry (SE) and photoluminescence (PL) measurements at RT were performed for this work. Materials and Methods: A 2-inch TlBr single crystalline ingot was grown by using the vertical Bridgman furnace. SE measurements were performed at RT within the photon energy range from 1.1 to 6.5 eV. PL measurements were performed at RT by using a home-made PL system equipped with a 266 nm-laser and a spectrometer. Results and Discussion: Dielectric responses from SE analysis were shown to be slightly different among the different samples possibly due to the different structural/optical properties. Also from the PL measurements, it was observed that the peak intensities of the middle samples were significantly higher than those of the other two samples. With the given values for permittivity of free space (${\varepsilon}_0=8.854{\times}10^{-12}F{\cdot}m^{-1}$), thickness (d = 1 mm), and area ($A=10{\times}10mm^2$) of the TlBr sample, capacitances of TlBr were 6.9 pF (at $h{\nu}=3eV$) and 4.4 pF (at $h{\nu}=6eV$), respectively. Conclusion: SE and PL measurement and analysis were performed to characterize TlBr samples from the optical perspective. It was observed that dielectric responses of different TlBr samples were slightly different due to the different material properties. PL measurements showed that the middle sample exhibited much stronger PL emission peaks due to the better material quality. From the SE analysis, optical, dielectric constants were extracted, and calculated capacitances were in the few pF range.

• Applied Chemistry for Engineering
• /
• v.28 no.3
• /
• pp.263-271
• /
• 2017

The application of mass spectrometry to polymer science has rapidly increased since the development of MALDI-TOF MS. This review summarizes current polymer analysis methods using MALDI-TOF MS, which has been extensively applied to analyze the average molecular weight of biopolymers and synthetic polymers. Polymer sequences have also been analyzed to reveal the structures and composition of monomers. In addition, the analysis of unknown end-groups and the determination of polymer concentrations are very important applications. Hyphenated techniques using MALDI-tandem MS have been used for the analysis of fragmentation patterns and end-groups, and also the combination of SEC and MALDI-TOF MS techniques is recommended for the analysis of complex polymers. Moreover, MALDI-TOF MS has been utilized for the observation of polymer degradation. Ion mobility MS, TOF-SIMS, and MALDI-TOF-imaging are also emerging technologies for polymer characterization because of their ability to automatically fractionate and localize polymer samples. The determination of polymer characteristics and their relation to the material properties is one of the most important demands for polymer scientists; the development of software and instrument for higher molecular mass range (> 100 kD) will increase the applications of MALDI-TOF MS for polymer scientists.

• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.170-187
• /
• 2010

Much interest on the thermoplastic elastomers (TPEs) has recently been attracted in commercial fields as well as scientific and applied researches. The TPEs have their own characteristic area especially in relation with block copolymers as well as many other polymeric materials, since they show interesting features displayed by the conventional vulcanized rubber, and at the same time, by the thermoplastics. In addition, they are characterized by a set of interesting properties inherent to block and graft copolymers, variety of blends and vulcanized materials. The importance of TPE as organic materials can be evaluated by the number of published reports (papers, patents, technical reports, etc). The input of the concept 'thermoplastic elastomer' to SciFinderScholar yields 18,508 results between 1939 and July 10, 2010, and the number increased exponentially after the mid of 1990. For the suitable introduction of the TPE, historic, scientific, technical and commercial considerations should be taken into account. This review article starts with a brief discussion on historical considerations, followed by a introduction of the main preparations and analytical techniques utilized in chemical, structural, and morphological studies. The properties, processing tools, the position among organic materials, and applications of TPEs are also briefly reviewed. Finally, the most probable trends of their future development are discussed in a short final remarks.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.173-173
• /
• 2010

$Bi_4Ti_3O_{12}$ ($B_4T_3$) is a unique ferroelectric material that has a relatively high dielectric constant, high Curie temperature, high breakdown strength, and large spontaneous polarization. As a result this material has been widely studied for many applications, including nonvolatile ferroelectric random memories, microelectronic mechanical systems, and nonlinear-optical devices. Several reports have appeared on the use of Mn dopants to improve the electrical properties of $B_4T_3$ thin films. Mn ions have frequently been used for this purpose in thin films and multilayer capacitors in situations where intrinsic oxygen vacancies are the major defects. However, no systematic study of the optical properties of $B_4T_3$ films has appeared to date. Here, we report optical data for these films, determined by spectroscopic ellipsometry (SE). We also report the effects of thermal annealing and Mn doping on the optical properties. The SE data were analyzed using a multilayer model that is consistent with the original sample structure, specifically surface roughness/$B_4T_3$ film/Pt/Ti/$SiO_2$/c-Si). The data are well described by the Tauc-Lorentz dispersion function, which can therefore be used to model the optical properties of these materials. Parameters for reconstructing the dielectric functions of these films are also reported. The SE data show that thermal annealing crystallizes $B_4T_3$ films, as confirmed by the appearance of $B_4T_3$ peaks in X-ray diffraction patterns. The bandgap of $B_4T_3$ red-shifts with increasing Mn concentration. We interpret this as evidence of the existence deep levels generated by the Mn transition-metal d states. These results will be useful in a number of contexts, including more detailed studies of the optical properties of these materials for engineering high-speed devices.

• Applied Chemistry for Engineering
• /
• v.29 no.3
• /
• pp.342-349
• /
• 2018

In this study, the physicochemical properties, emulsifying capacity, moisture content and cytotoxicity of the composite material produced by transesterification reactions of the olive oil (olive oil esters) were investigated for cosmetic applications. Olive oil esters with short (S) and long (L) reaction times were studied. From the TLC-image analysis, composition ratios of the olive oil esters S were found to be 5.2, 24.1, 46.4, and 21.9% for mono-, di-, tri-glyceride, and fatty acid ethyl ester, respectively. Those of the olive oil esters L were 4.1, 24.7, 40.6, and 28.8% for mono-, di-, tri-glyceride, and fatty acid ethyl ester, respectively. The iodine value, acid value, saponification value, unsaponified matter, refractive index, and specific gravity were determined and purity tests were also carried out and normalized to establish standards and testing methods for using olive oil esters in cosmetics. To evaluate their emulsifying capacities, the O/W emulsion was prepared without surfactants and the formation of the emulsified particles were confirmed. After 5 days of applying the olive oil esters to human skin, the skin moisture retention was improved by 13.1% from the initial state. For the evaluation of toxicity on human skin cells, the olive oil esters showed 90% or more of the cell viability at $0.2-200{\mu}g/mL$. These results suggested that olive oil esters can be applied as natural/non-toxic ingredients to cosmetics industries.

• Food Science of Animal Resources
• /
• v.23 no.1
• /
• pp.9-15
• /
• 2003

All diets were based on feeds of fattening period pigs(LY x D, ca. 90 kg) with six treatments, which were the control, containing 5% beef tallow(C), 3% beef tallows and 2% perilla seeds oil(T1), 250 ppm vit. E(${\alpha}$-tocopheryl acetate) in T1(T2), 3% beef tallow and 2% squid viscera oil(T3), 250 ppm vit. E in T3(T4), and 3% beef tallow and 2% CLA(T5), respectively. Produced porks and their carcass characteristics were as follows. The daily gain of pigs was higher in T2 and 73 than any other treatments(p<0.05). Its T2 and T3 was 3.71 and 3.80 respectively, however, there was no significance in feed intake. The highest back fat thickness was shown in control group on market weight, while there was no significant difference on their initial weight. Loin-eye muscle area did not show any significant difference on initial weight and on market weight, however, its T5 was about twice as large as T2's. Content of triglyceride in blood was high in control group as compared to others; especially, the values for T3, T4 and T5 were significantly low(p <0.05). There was no significant difference in total cholesterol contents, and the ratio of HDL cholesterol/total cholesterol was higher in vit. E treated samples than untreated sample. Atherogenic index was high in sample with T3 and low in sample with T2. The perilla seed oil, squid fish oil, and vit. E decreased atherogenic index. Dressing percentage, back fat thickness, and grade did not show any significant difference(p >0.05); however, T2, C and T3, T1 and T5 showed 4.67, 4.29, 4.00 respectively, in grades.