• Journal of Korean Society of Environmental Engineers
• /
• 제28권2호
• /
• pp.173-177
• /
• 2006

Pesticides from diffuse pollution sources adsorbed in suspended particles flow into surface water and threats to the public health. In this research, dechlorination constants of Atrazine by zero valent iron were measured with addition of buffer solution for simulating buffer capacity of sediment. When initial concentration of Atrazine was 10, 30, and 50 mg/L, their dechlorination was explained using the pseudo-first order reaction. Dechlorination constants $K_{obs}$ were $3.21{\times}10^{-2}/d$ in average.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• 제36D권10호
• /
• pp.61-70
• /
• 1999

In this paper, we analyze several exposure time schedules to obtain uniform multiple hologram and measure the diffraction efficiencies of holograms stored in $LiNbO_3$:Fe(0.015wt%) crystal through experiments. The minimum angular selectivity and the intensity ration of two incident beams are investigated precisely by the high resolution system(minimum angle : $0.0028^{\circ}$). Considering initial recording time, total exposure time and time constants, the efficiency distribution(0.014 ${\pm}$ 0.005%) of 100 holograms is measured and the 330 analog images are recorded in the same place. Also, total 500 holograms are retrieved by spatial multiplexing.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• 제16권5호
• /
• pp.134-139
• /
• 2007

This paper presents a computer-based analysis on the thermal shock characteristics of Pb-free solder joints and UBM in flip chip assemblies. Among four types of popular UBM systems, TiW/Cu system with 95.5Sn-3.9Ag-0.6Cu solder joints was chosen for simulation. A simple 3D finite element model was first created only including silicon die, mixture between underfill and solder joints, and substrate. The displacements due to CTE mismatch between silicon die and substrate was then obtained through FE analysis. Finally, the obtained displacements were applied as mechanical loads to the whole 2D FE model and the characteristics of flip chip assemblies were analyzed. In addition, based on the hyperbolic sine law, the accumulated creep strain of Pb-free solder joints was calculated to predict the fatigue life of flip chip assemblies under thermal shock environments. The proposed method for fatigue life prediction will be evaluated through the cross check of the test results in the future work.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• 제36D권6호
• /
• pp.79-86
• /
• 1999

We propose a new photorefractive demultiplexer(DMUX) for WDM communicaytion system using a wavelength selectivity and demultiplexing properties of a volume holographic grating filters formed in $LinbO_3$ crystal doped with 0.015wt.% Fe. The wavelength selectivity properties of the filter are analyzed and experimentally investigated as a function of the following parameters : the crossing angle of the two writing beams, the reading-beam angle and writing-beam size. In addition, applying these wavelength selectivity properties and the multiplexing technique for recording multiple-exposure filters with equal diffraction efficiency, some preliminary experimental results are presented for use as DMUX.

• Transactions of Materials Processing
• /
• 제14권2호
• /
• pp.126-132
• /
• 2005

The isothermal forging design of a Ti-6Al-4V wing shape was performed by 3D FE simulation. The design focuses on near-net shape forming by the single stage. The process variables such as the die design, pre-form shape and size, ram speed and forging temperature were investigated. The main design priorities were to minimize forging loads and to distribute strain uniformly in a given forging condition. The FE simulation results for the final process design were compared with the isothermal forging tests. The instability of deformation was evaluated using a processing map based on the dynamic materials model(DMM), including flow stability criteria. Finally, a modified process design for producing a uniform Ti-6Al-4V wing product without forming defects was suggested.

• Computers and Concrete
• /
• 제20권5호
• /
• pp.583-593
• /
• 2017

Applications of fibre-reinforced polymer (FRP) composites for retrofitting, strengthening and repairing concrete structures have been expanded dramatically in the last decade. FRPs have high specific strength and stiffness compared to conventional construction materials, e.g., steel. Ease of preparation and installation, resistance to corrosion, versatile fabrication and adjustable mechanical properties are other advantages of the FRPs. However, there are major concerns about long-term performance, serviceability and durability of FRP applications in concrete structures. Therefore, structural health monitoring (SHM) and damage detection in FRP-retrofitted concrete structures need to be implemented. This paper presents a study on investigating the application of Rayleigh wave for detecting debonding defect in FRP-retrofitted concrete structures. A time-of-flight (ToF) method is proposed to determine the location of a debonding between the FRP and concrete using Rayleigh wave. A series of numerical case studies are carried out to demonstrate the capability of the proposed debonding detection method. In the numerical case studies, a three-dimensional (3D) finite element (FE) model is developed to simulate the Rayleigh wave propagation and scattering at the debonding in the FRP-retrofitted concrete structure. Absorbing layers are employed in the 3D FE model to reduce computational cost in simulating the practical size of the FRP-retrofitted structure. Different debonding sizes and locations are considered in the case studies. The results show that the proposed ToF method is able to accurately determine the location of the debonding in the FRP-retrofitted concrete structure.

• Applied Science and Convergence Technology
• /
• 제27권3호
• /
• pp.47-51
• /
• 2018

We fabricated an anode-type ion beam source and studied its driving characteristics of the initial extraction of ions using two driving mechanisms: a diffusion phenomenon and a charge repulsion phenomenon. For specimen exposed to the ion beam in two methods, the surface impurity element was investigated by using X-ray photoelectron spectroscopy. Upon Ar gas injection for plasma generation the ion beam source was operated for 48 hours. We found a Fe 2p peak 5.4 at. % in the initial ions by the diffusion mechanism while no indication of Fe in the ions released in the charge repulsion mechanism. As for a long operation of 200 min, the temperature of ion beam sources was measured to increase at the rate of ${\sim}0.1^{\circ}C/min$ and kept at the initial value of $27^{\circ}C$ for driving by diffusion and charge repulsion mechanism, respectively. In this study, we confirmed that the ion beam source driven by the charge repulsion mechanism was very efficient for a long operation as proved by little electrode damage and thermal stability.

• Computers and Concrete
• /
• 제26권1호
• /
• pp.11-20
• /
• 2020

Concrete are the most widely used manmade materials for infrastructure construction across the world. These constructions gradually aged and damaged due to long-term use. However, there does not exist an efficient concrete recycling method with low energy consumption. In this study, concrete was regarded as a heterogeneous material composed of coarse aggregate and cement mortar. And the failure mode of concrete under ultrasonic dynamic loading was investigated by finite element (FE) analysis. Simultaneously, a 3D random aggregate concrete model was programmed by APDL and imported into ABAQUS software, and the damage plastic constitutive model was applied to each phase to study the damage law of concrete under dynamic loading. Meanwhile, the dynamic damage process of concrete was numerically simulated, which observed ultrasonic propagating and the concrete crushing behavior. Finally, the FE simulation considering the influence of different aggregate volume and aggregate size was carried out to illustrate the damage level of concrete.

• Special Issue of the Society of Naval Architects of Korea
• /
• 대한조선학회 2005년도 특별논문집
• /
• pp.63-68
• /
• 2005

Optimum design of the big brackets is performed through iterated 3-D FE analyses to meet the permissible limits of stress, which consumes an excessive amount of calculation time. Therefore, this study has been prepared to determine rapidly and accurately an optimum size and scantling of the big brackets at the initial design stage. The generalized slope deflection method (GSDM) based on the span point concept is applied to enhance the efficiency of iterated structural analyses. The accuracy and applicability of the present method is verified by comparing with a detail 3-D FE analysis of web frame structures. As an optimization technique, evolution strategies (ES) are applied using discrete design variables for practical design.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제27권9호
• /
• pp.1469-1476
• /
• 2003

This paper provides plastic limit load solutions of cylinders with circumferential part-through surface cracks under combined axial tension, internal pressure and global bending. Such solutions are developed based on detailed three-dimensional (3-D) finite element (FE) limit analyses using elastic-perfectly-plastic material behaviour, together with analytical solutions based on equilibrium stress fields. For the crack location, both external and internal cracks are considered. Furthermore, in terms of the crack shape, both semi-elliptical and constant-depth surface cracks are considered. The resulting limit load solutions are given in a closed form, and thus can be easily used in practical situations. Being based on detailed 3-D FE limit analysis, the present solutions are believed to most reliable, and thus to be valuable information for integrity assessment of piping.