• 한국물환경학회지
• /
• 제18권3호
• /
• pp.245-251
• /
• 2002

Reactive dyes waste water, a toxic and refractory pollutant, was treated by an electrochemical method using $Ti/IrO_2$ as anode and Stainless Steel 316 as cathode. In this technique, sodium chloride as an electrolyte was added. A number of experiments were run in a batch system. Artificial samples (reactive blue 19, red 195, yellow 145) were used. Operation parameters, such as supporting electrolyte concentration, current density, pH and sample concentration have been investigated for their influences on COD and color removal efficiencies during electrolysis. After 5 and 90 minites of eletrolysis, color was reduced by 51.5% and 98.9% respectively. Under the condition of current density $10A/dm^2$, NaCl concentration 12mg/l and pH 3, 62.9% of $COD_{Cr}$ was removed after electrolysis for 90 minites. The optimum condition of color removal and COD reduction in this work was found to be the following : pH 3, sodium chloride concentration 20g/l, current density $10A/dm^2$. As a result, we confirmed to be effective to color removal and reduction of refractory organic material.

• Corrosion Science and Technology
• /
• 제5권4호
• /
• pp.129-136
• /
• 2006

High temperature corrosion behavior of AISI-type 316L stainless steel for the MCFC(molten carbonate fuel cell) bipolar application was studied by immersion test and penetration attack method in anode environment ($650^{\circ}C$, $Li_2CO_3/K_2CO_3=62/38$ mol%, $H_2/CO_2=80/20$ vol%) without or with different $CaCO_3$ content. Not only immersion test method but also morphological observation of samples in the carbonate melts are adopted as experimental methods. With aid of the morphological observation of cross section of samples immersed in a carbonate melt was possible to obtain penetration attack. The concentration effect of $CaCO_3$ inhibitor was investigated in order to verify the optimum concentration for practical application in MCFC stack operation. The corrosion rate in the presence of $CaCO_3$ was proven to be decreased as a function of $CaCO_3$ concentration. The corrosion rate in the presence of $CaCO_3$ was measured with a value of 6.9 mpy which is 2.4 times lower than that of inhibitor-free electrolyte. The cross section microscopy revealed that the internal penetration by oxidation in molten carbonate is very severe. In this case, the attack was occurred not only dissolution loss in the electrolyte by corrosion reaction but also weight gain through oxide layer by internal penetration.

• 열처리공학회지
• /
• 제22권5호
• /
• pp.267-274
• /
• 2009

Titanium Chromium Nitrided (TiCrN) coatings were deposited on stainless steel 316 L and Si (100) wafer by inductively coupled plasma assisted D.C. magnetron sputtering at the various sputtering power on Cr target and $N_2/Ar$ gas ratio. Increasing the sputtering power of Cr target, XRD patterns were changed from TiCrN to nitride $Cr_2Ti$. The maximum hardness was $Hk_{3g}$ 3900 at $0.3\;N_2/Ar$ gas ratio. The thickness of the TiCrN films increased as the Cr target power increased, and it showed over $Hk_{5g}3100$ hardness at 100 W, 150 W. TiCrN films were deposited by the ICP assisted DC magnetron sputtering shown good wear resistance as the $N_2/Ar$ gas ratio was 0.1, 0.3.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.331-337
• /
• 2010

This study compared the macro and micro electrochemical characteristics at the local area of welding metal on dissimilar welding parts for type 304 stainless steel (SS) and type 316L SS. The materials are used for double wall gas pipe of duel fuel engine for a ship. The various potentiodynamic experiments were performed several times in 10% ${H_2C_2O_2}{\cdot}{H_2O}$ solution using macro and micro methods, respectively. The micro electrochemical experiments conducted to resolve at local area on cross-section of dissimilar welding materials by micro-droplet cell device. The micro-droplet cell techniques can be used almost electrochemical experiments to resolve corrosion characteristics of the limited electrode area of the metallic surface between wetted spot of working electrode and tip of sharpened capillary tube. The results of macro electrochemical experiments show that resistance of active dissolution reaction at welding zone was high due to low current density by formation of passivation protection film at passive region. According to the micro electrochemical experiment, the corrosion current density of welding zone and bond zone were relatively high.

• Journal of Yeungnam Medical Science
• /
• 제7권1호
• /
• pp.81-93
• /
• 1990

1983년 5월부터 1989년 9월까지 본 영남의료원 정형외과에 대퇴골 간부골절시 사용한 금속 내 고정물의 금속 부전으로 입원한 경우 중 부전된 금속의 표면관찰이 가능한 8례에 대한 임상적 고찰 및 부전된 금속 파손 표면의 관찰을 통해 확인한 파손 원인을 요약하면 다음과 같다. 1. 금속 부전이 발생 내고정물의 종류는 압박금속판 5례, Jewett nail 1례, Rowe plate screw 1례, interlocking nail 1례였다. 2. 금속 부전의 임상적 추정에 의한 원인으로는 반대편 피질골 결손 5례, 부적절한 위치선정 1례 및 부적절한 금속선택 1례였다. 3. 금속 내고정후 금속 부전이 되기까지의 기간을 보면, 4개월이 1례, 6개월에서 12개월 사이가 6례, 3년이 1례였다. 4. 부전된 내고정물의 파손면 관찰을 통해 확인한 금속부전의 원인을 보면, 첫째, impact failure 1례 둘째, fatigue failure 6례 machining mark가 있어 이것이 stress riser로서 역할을 한 것으로 보이는 경우가 4례였으며, 이의 형태는 low consistent cyclic fatigue failure와 irregular cyclic fatigue failure의 형태를 관찰할 수 있었다. 셋째, Stress corrosion crack 1례를 관찰할 수 있었다. 5. 316L Stainless Steel은 내부식성이 좋은 금속이지만 fretting에 의해 특유의 부동태 피막이 손상되면 pitting corrosion을 일으키며 경우에 따라서는 파손의 기점으로 작용되어 failure의 주요 원인이 되기도 한다. 6. screw hole의 가공시 기계에 의한 손상 및 기구(implant) 제조 과정중 손상이 plate의 failure를 유발하는 중요한 원인이 될 수도 있다. 기계에 의한 손상은 응력을 집중시키므로 plate가 파손되기 쉽게 한다. 이상의 결과 임상적 추정에 의한 원인 이외에도 부전된 금속파손면 관찰을 통해 중요한 다른 원인을 찾을 수 있었으므로, 금속부전의 예방을 위해 앞으로 이 방향으로의 계속적인 연구가 필요할 것으로 사료된다.

• 대한의용생체공학회:의공학회지
• /
• 제25권2호
• /
• pp.157-163
• /
• 2004

금속 임플란트 재료들의 마모저항을 향상시키기 위하여 질소 이온주입 및 이온도금 기술을 적용하였다. 질소 이온주입 된 초내식성 스테인리스강(S.S.S)의 마모이온용출 특성을 S.S.S, 316L SS, TiN코팅된 316S SS와 비교 평가하기 위하여 탄소로 원자흡수분광분석기를 이용하여 시편들로부터 마모용출된 Cr과 Ni 이온량을 측정하였다. 또한, 저온아크증착법을 이용하여 TiN, ZrN, TiCN코팅된 Ti(Grade 2)원반의 마모저항을 비교하였고, 질소이온주입 및 질화물 코팅된 표면충의 화학적 조성은 SAES(scanning Auger electron spectroscopy)를 이용하여 분석하였다. 질소 이온주입된 S.S.S 표면으로부터 마모에 의하여 용출된 Cr과 Ni 이온량은 표면처리하지 않은 스테인리스강들에 비하여 크게 감소하였다 그러나 인공고관절에 걸리는 하중조건 하에서 실행된 마모이온용출실험에서 이온에너지 100 KeV로 질소이온 주입된 표면층은 20만회 내에서 쉽게 제거되었다. 질화물 코팅된 Ti 시편들의 마모저항도 크게 향상되었고, 그 마모특성은 코팅층의 화학적 조성에 따라 크게 차이가 났다. 코팅두께 3Um의 코팅시편들 중 TiCN 코팅된 티타늄이 가장 높은 내마모 특성을 보였으나 같은 하중조건 하에서 disk(Ti)-on-disk 마모실험에서 그 질화물 코팅면들의 마모 무게감 소비는 1만회 아래에서 모두 Ti의 마모비와 유사하게 전환되었다. 본 실험으로부터 얻어진 연구결과에 의하면, 100 KeV 질소이온주입 및 두께 3$\mu\textrm{m}$의 길화코팅된 표면층의 경우 표면 경화충의 깊이가 충분치 않아 높은 하중을 받는 임플란트의 마찰부위에 사용하기에는 한계가 있음을 보였다.

• Restorative Dentistry and Endodontics
• /
• 제42권4호
• /
• pp.316-323
• /
• 2017

Objectives: This study compared the amount of apically extruded bacteria during the glide-path preparation by using multi-file and single-file glide-path establishing nickel-titanium (NiTi) rotary systems. Materials and Methods: Sixty mandibular first molar teeth were used to prepare the test apparatus. They were decoronated, blocked into glass vials, sterilized in ethylene oxide gas, infected with a pure culture of Enterococcus faecalis, randomly assigned to 5 experimental groups, and then prepared using manual stainless-steel files (group KF) and glide-path establishing NiTi rotary files (group PF with PathFiles, group GF with G-Files, group PG with ProGlider, and group OG with One G). At the end of canal preparation, 0.01 mL NaCl solution was taken from the experimental vials. The suspension was plated on brain heart infusion agar and colonies of bacteria were counted, and the results were given as number of colony-forming units (CFU). Results: The manual instrumentation technique tested in group KF extruded the highest number of bacteria compared to the other 4 groups (p < 0.05). The 4 groups using rotary glide-path establishing instruments extruded similar amounts of bacteria. Conclusions: All glide-path establishment instrument systems tested caused a measurable apical extrusion of bacteria. The manual glide-path preparation showed the highest number of bacteria extruded compared to the other NiTi glide-path establishing instruments.

• Nuclear Engineering and Technology
• /
• 제26권1호
• /
• pp.140-148
• /
• 1994

원전 증기발생기 2차측 제철 화학세정을 기존의 93$^{\circ}C$ 표준공정보다 고온인 1$25^{\circ}C$에서 검증시험을 수행하였다. 원전 증기발생기를 1$25^{\circ}C$에서 화학 세정한다는 가정아래 현장세정 조건을 결정하고 이를 다시 모사하여 3l 용량의 소형 검증시험 조건을 결정하였다. 1 gallon 용량의 316 스텐레스강 압력용기를 반응용기로 사용하는 화학세정 시험장치에서 검증시험을 수행하여 스러지 용해거동, 모재 부식률, 세정제 화학조성 변화거동 등을 측정하였다. 1$25^{\circ}C$ 검증시험 결과에서 93$^{\circ}C$ 표준공정보다 세정시간을 절반이하로 단축시키고도 더 효율적인 세정효과를 얻을 수 있을 뿐만이 아니라 2차측 모재의 부식률도 감소함을 확인할 수 있었다. 그러나 고온 세정공정은 아직 현장적용 경험이 없고, 별도의 외부순환 세정 장치를 이용하는 93$^{\circ}C$ 표준공정과는 달리 주냉각재의 잠열로 2차측을 가열하므로 세정이 완료될 때까지 주냉각 펌프를 계속 가동하여야 하는 단점이 있다. 가동중인 증기발생기에 대한 화학세정을 수행할 때 93$^{\circ}C$ 표준공정과 고온공정의 장 단점을 신중히 검토하여 최적공정을 적용하여야 할 것이다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.348-351
• /
• 2006

Bipolar plate, which forms about 50% of the stack cost, is an important core part with polymer electrolyte membrane in PEMFC. Bipolar plates have been commonly fabricated from graphite meterial having high electrical conductivity and corrosion resistance. Lately, many researchers have concentrated their efforts on the development of metallic bipolar plate and stainless steel has been considered as a potential material for metallic bipolar plate because of its high strength, chemical stability, low gas permeability and applicability to mass production. However, it has been reported that its inadequate corrosion behavior under PEMFC environment lead to a deterioration of membrane by dissolved metal ions and an increase in contact resistance by the growth of passive film therefore, its corrosion resistance as well as contact resistance must be improved for bipolar plate application. In this work, several types of coating were applied to 316L and their electrical conductivity and corrosion resistance were evaluated In the simulated PEMFC environment. Application of coating gave rise to low interfacial contact resistances below $19m{\Omega}cm^2$ under the compress force of $150N/cm^2$. It also made the corrosion potential to shift in the posit ive direct ion by 0.3V or above and decreased the corrosion current from ca. $9{\mu}A/cm^2$ to ca. $0.5{\mu}A/cm^2$ in the mixed solution of $0.1N\;N_2SO_4$ and 2ppm HF A coat ing layer under potentiostatic control of 0.6V and $0.75V_{SCE}$ for 500 hours or longer showed some instabilities, however, no significant change in coat Ing layer were observed from Impedance data. In addition, the corrosion current maintained less than $1{\mu}A/cm^2$ for most of time for potentiostatic tests. It indicates that high electrical conductivity and corrosion resistance can be obtained by application of coatings in the present work.