초록
금속 임플란트 재료들의 마모저항을 향상시키기 위하여 질소 이온주입 및 이온도금 기술을 적용하였다. 질소 이온주입 된 초내식성 스테인리스강(S.S.S)의 마모이온용출 특성을 S.S.S, 316L SS, TiN코팅된 316S SS와 비교 평가하기 위하여 탄소로 원자흡수분광분석기를 이용하여 시편들로부터 마모용출된 Cr과 Ni 이온량을 측정하였다. 또한, 저온아크증착법을 이용하여 TiN, ZrN, TiCN코팅된 Ti(Grade 2)원반의 마모저항을 비교하였고, 질소이온주입 및 질화물 코팅된 표면충의 화학적 조성은 SAES(scanning Auger electron spectroscopy)를 이용하여 분석하였다. 질소 이온주입된 S.S.S 표면으로부터 마모에 의하여 용출된 Cr과 Ni 이온량은 표면처리하지 않은 스테인리스강들에 비하여 크게 감소하였다 그러나 인공고관절에 걸리는 하중조건 하에서 실행된 마모이온용출실험에서 이온에너지 100 KeV로 질소이온 주입된 표면층은 20만회 내에서 쉽게 제거되었다. 질화물 코팅된 Ti 시편들의 마모저항도 크게 향상되었고, 그 마모특성은 코팅층의 화학적 조성에 따라 크게 차이가 났다. 코팅두께 3Um의 코팅시편들 중 TiCN 코팅된 티타늄이 가장 높은 내마모 특성을 보였으나 같은 하중조건 하에서 disk(Ti)-on-disk 마모실험에서 그 질화물 코팅면들의 마모 무게감 소비는 1만회 아래에서 모두 Ti의 마모비와 유사하게 전환되었다. 본 실험으로부터 얻어진 연구결과에 의하면, 100 KeV 질소이온주입 및 두께 3$\mu\textrm{m}$의 길화코팅된 표면층의 경우 표면 경화충의 깊이가 충분치 않아 높은 하중을 받는 임플란트의 마찰부위에 사용하기에는 한계가 있음을 보였다.
Nitrogen ion implantation and ion plating techniques were applied for improvement of the wear resistance of metallic implant materials. In this work, the wear dissolution behaviour of a nitrogen ion implanted super stainless steel (S.S.S, 22Cr-20Ni-6Mo-0.25N) was compared with those of S.S.S, 316L SS and TiN coated 316L SS. The amounts of Cr and Ni ions worn-out from the specimens were Investigated using an electrothermal atomic absorption spectrometry. Furthermore, the Ti(Grade 2) disks were coated with TiN, ZrN and TiCN by use of low temperature arc vapor deposition and the wear resistance of the coating layers was compared with that of titanium. The chemical compositions of the nitrogen ion implanted and nitride coated layers were examined with a scanting auger electron spectroscopy. It wat observed that the metal ions released from the nitrogen ion implanted S.S.S surface were significantly reduced. From the results obtained, it was shown that the nitrogen ion implanted zone obtained with 100 KeV ion energy was easily removed within 200,000 revolutions from a wear dissolution testing under a similar load condition when applied to artificial hip joint. The remarkable improvement in wear resistance weir confirmed by the nitrides coated Ti materials and the wear properties differ greatly according to the chemical composition of the coating layers. for specimens with the same coating thickness of about 3$\mu\textrm{m}$, TiCN coated Ti showed the highest wear resistance. However, after removing the coating layers, the wear rates of all nitrides coated Ti reverted to their normal rates of below 10,000 revolutions from Ti-disk-on-disk wear testing under the same load condition. From the results obtained, it is suggested that the insufficient depth of the 100 Kel N$\^$+/ ion implanted zone and of the nitrides coated layers of 3$\mu\textrm{m}$ are subject to restriction when used as frictional parts of load bearing implants.