• 소성∙가공
• /
• 제29권3호
• /
• pp.163-171
• /
• 2020

We present a multi-step cold drawing for a non-equiatomic Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ high entropy alloy (HEA) with a simple face-centered cubic (FCC) crystal structure. The distribution of strain in the cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wires was analyzed by the finite element method (FEM). The effective strain was expected to be higher as it was closer to the surface of the wire. However, the reverse shear strain acted to cause a transition in the shear strain behavior. The critical effective strain at which the shear strain transition behavior is completely shifted was predicted to be 4.75. Severely cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wires up to 96% of the maximum cross-sectional reduction ratio were successfully manufactured without breakage. With the assistance of electron back-scattering diffraction and transmission electron microscope analyses, the abundant deformation twins were found in the region of high effective strain, which is a major strengthening mechanism for the cold-drawn Co₁₀Cr₁₅Fe₂₅Mn₁₀Ni₃₀V₁₀ HEA wire.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.183-188
• /
• 2007

In this paper, we propose a 2D-FE model in single impact with combined physical factors to obtain a unique residual stress by shot peening. Applied physical parameters include elastic-plastic deformation of shot ball, material damping coefficients, strain rate, dynamic friction coefficients. Single impact FE model consists of 2D axisymmetric elements. The FE model with combined factors showed converged and unique distributions of surface stress, maximum compressive residual stress and deformation depth. Further, in contrast to the FE models with rigid shot and elastic deformable shot, FE model with plastic deformable shot produces residual stresses very close to experimental solutions by X-ray diffraction. We therefore validated the 2D FE model with combined peeing factors and plastic deformable shot. This FE model will be a base of the 3D FE model for residual stresses by multi-impact shot peening.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1097-1103
• /
• 1988

본 연구에서는 이 좁은 벤트내에 자료가 모이는 피로균열의 특성을 이용하여 표면피로균열의 성장거동을 파괴역학적으로 해석, 연구하여 균열의 성장특성과 $S-N_{f}$ 곡선의 추정을 마이크로 컴퓨터로 계산하였다.

• 대한의용생체공학회:의공학회지
• /
• 제34권1호
• /
• pp.14-23
• /
• 2013

In this study, biomechanical stability of the newly developed revision total knee arthroplasty (rTKA) was evaluated through strain and stress distribution analysis within the implanted proximal tibia using a three-dimensional finite element (FE) analysis. 2000N of compressive load (about 3 times body weight) was applied to the condyle surface on spacer, sharing by the medial (60%) and lateral (40%) condyles simulating a stance phase before toe-off. The results showed that PVMS within the revision total knee arthroplasty and the proximal tibia were less than yield strength considering safe factor 4.0 (rTKA: less than 10%, Cortical bone: less than 70%, Cancellous bone: less than 70%). The materials composed of them and the strain and stress distributions within the proximal tibia were generally well matched with those of a traditional revision total knee arthoplasty (Scorpio TS revision system, Stryker Corp., Michigan, USA) without the critical damage strain and stress, which may reduce the capacity for bone remodeling, leading to bone degeneration. This study may be useful to design parameter improvement of the revision total knee arthoplasty in biomechanical stability point of view beyond structural stability of revision total knee arthoplasty itself.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제39권1호
• /
• pp.9-13
• /
• 2019

In this study, 4 different types of GBR membrane were undergone for bio-degradability test; Silk mat from silkworm cocoon (TDI), silk mat from flatwise-spun (FS), collagen membrane (OssGuide), and dPTFE membrane (Cytoplast). Each material was segmented in 10.00 mm length and 0.3 mm thickness. The samples were put into the normal saline at $37^{\circ}C$ for 2 weeks. After that, yield strength and tensile strain were measured and compared them with those of before treatment. The morphology of the membranes was observed by SEM. Tensile strain of FS was significantly increased at 2 weeks' normal saline treatment (P=0.018). When compared to OssGuide, TDI and FS showed significantly higher tensile strain at 2 weeks' normal saline treatment (P<0.05). In the SEM images, there were no significant changes in Cytoplast, TDI, and FS after 2 weeks' treatment. However, OssGuide showed damaged surface after 2 weeks' treatment. In conclusion, both TDI and FS did not have any evidence of biodegradability at 2 weeks' observation in normal saline treatment. However, OssGuide showed more than 20 % decrease in yield strength and tensile strain.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.124-127
• /
• 2007

In this study, we focused on investigation of governing parameters affected on the fatigue properties in the hyper-eutectoid steel wires used for TBR tires. Steel wires are fabricated under different drawing strain from 3.36 to 3.80. Their diameters are 0.21 mm and 0.185mm, respectively. The fatigue properties was measured by hunter rotating beam tester, specially designed thin-sized steel wires. The results showed that the fatigue properites of steel wire, marked as A-1, were greater than the others, due to the low value of residual stress. In order to elucidate the variations of fatigue properties, the microstructure, surface defect and residual stress were observed and measured by useful analysis technique, such as TEM, 3D profiler and FIB.

• 한국재료학회지
• /
• 제27권12호
• /
• pp.688-694
• /
• 2017

Porous materials such as polymeric foam are widely adopted in engineering and biomedical fields. Porous materials often exhibit complex nonlinear behaviors and are sensitive to material and environmental factors including cell size and shape, amount of porosity, and temperature, which are influenced by the type of base materials, reinforcements, method of fabrication, etc. Hence, the material characteristics of porous materials such as compressive stress-strain behavior and void volume fraction according to aforementioned factors should be precisely identified. In this study, unconfined uniaxial compressive test for two types of closed-cell structure polyurethane foam, namely, 0.16 and $0.32g/cm^3$ of densities were carried out. In addition, the void volume fraction of three different domains, namely, center, surface and buckling regions under various compressive strains (10 %, 30 %, 50 % and 70 %) were quantitatively observed using Micro 3D Computed Tomography(micro-CT) scanning system. Based on the experimental results, the relationship between compressive strain and void volume fraction with respect to cell size, density and boundary condition were investigated.

• 한국항공우주학회지
• /
• 제30권8호
• /
• pp.103-111
• /
• 2002

열하중과 원심력을 고려한 발전용 터빈 블레이드의 정상 상태 크리프 해석을 수행하였다. 3차원 터빈 블레이드 유한 요소 모델에 대하여 크리프 변형률과 응력을 계산하고 수치적 방법에 의해 크리프 수명을 예측하였다. 약 200시간 정도의 크리프 해석 결과 GTD111 터빈 블레이드는 아직 파손 응력에 도달하지 않았으며, 크리프 응력은 시간이 경과함에 따라 점차 이완되고 있다. 터빈 블레이드의 최대 크리프 변형률은 익형의 압력면 끝단에서 발생하며 수치적 방법에 의해 약 50,000 시간 이후에 파손 변형률에 도달할 것이다. 따라서 현재 터빈의 기동 중 블레이드는 크리프에 의한 손상을 입지 않는다.

• 한국지반신소재학회논문집
• /
• 제15권4호
• /
• pp.25-32
• /
• 2016

지반공학에서 평면변형율을 가정하는 2차원 사면안정해석은 일반적으로 널리 사용되고 있다. 이 가정은 사면활동이 넓은 영역에 걸쳐서 발생되는 가정이므로 3차원 효과가 무시된다. 대다수 연구에서 2차원해석의 최소안전율값은 3차원해석에 비하여 작게 평가되는 보수적인 결과를 나타낸다. 최근에는 컴퓨터의 소프트웨어와 하드웨어를 포함한 해석방법의 발달로 3차원해석에 대한 요구가 커지고 있다. 본 논문에서는 원호모드, 병진모드사면을 이용하여 유한요소에 의한 2, 3차원해석 및 2차원 한계평형해석을 통하여 수치해석을 실시하였다. 해석결과 매개변수(요소망크기, 체적팽창각(dilatency angle), 경계조건, 응력이력, 모델차원)에 따른 사면안정해석에 미치는 영향을 분석하였다. 해석결과 2차원 해석보다 3차원 해석에 의한 사면의 안전율 값은 항상 크게 평가되며, W 뱡향 경계조건이 롤러지지인 경우, 사면폭에 의한 결과 차이는 없는 것으로 조사되었다.

• 한국지반공학회논문집
• /
• 제37권10호
• /
• pp.13-25
• /
• 2021

트라우즐 연주시험은 화약의 발파성능을 검증하기 위해서 널리 사용되는 시험방법 중 하나이다. 위력이 검증된 폭약을 연주블록의 발파공에 장약 및 전색하여 폭발시킨 후 발파공의 체적변화를 통해 화약의 위력 또는 전색효과 등을 측정하는 방법이라 할 수 있다. 본 연구에서는 발파 시 전색물에 따른 전색효과를 서로 비교하기 위하여 트라우즐 연주시험 및 3차원 고속카메라를 이용한 이미지영상상관기법을 도입하여 발파실험을 수행하였다. 실험에 사용된 폭약은 산업용 에멀젼 폭약을 적용하였고, 전색재료는 모래 및 잔골재를 사용하였다. 트라우즐 연주시험 및 수치해석을 통한 비교에서 표준사보다 잔골재 전색의 경우가 연주블록의 확장이 크게 나타났으며, 3D-DIC 시스템에서도 잔골재 전색의 경우가 모래전색보다 직경변화와 표면변형률 모두 높은 수치를 보였다.