• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.11 s.114
• /
• pp.1058-1064
• /
• 2006

In this paper, the channel capacity of a specified wireless indoor multiple-input multiple-output(MIMO) channel is estimated by analyzing spatial characteristics of this channel using the three-dimensional ray tracing method, and a technique for deriving an optimized separation of multi-antenna elements is proposed. At first, the ray paths, the path losses, and the time-delay profile are computed using the three-dimensional ray tracing method in an indoor corridor environment, which has the line of sight(LOS) and non-line of sight(NLOS) regions. The ray tracing method is verified by a comparison between the computation results and the measurements which are obtained with dipole antennas, an amplifier and a network analyzer. Then, an MIMO system is positioned in the indoor channel environment and the ray paths and path losses are computed for four antenna-position combinations and various values of the antenna separation to obtain the channel capacity for the MIMO system. An optimum antenna-separation is derived by averaging the channel capacities of 100 receiver positions with four different antenna combinations.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.166-176
• /
• 2007

Measurement uncertainty assessment is very important in measurement and calibration. RRL provides antenna calibration services for EMI test. Reliability of EMI test depends on accurate antenna calibration. Antenna calibration results have to be accompanied with measurement uncertainty for its better reliability. In the late of 2005, CISPR issued the CISPR/A/644/C which describes the antenna calibration and measurement uncertainty. In this paper, on the basis of CISPR/A/644/C, we provide the measurement uncertainty values for dipole antenna calibration at the Calibration Test Site(CALTS) of Icheon. The antenna calibration method is 3-antenna height-scanning-averaging method, which measures the free-space antenna factor. We also considered all uncertainty sources that can affect measurement results during calibration.

• International journal of advanced smart convergence
• /
• v.4 no.2
• /
• pp.29-33
• /
• 2015

In this paper, we propose the method to improve the performance of the antenna system that contains three bands, such as Lte3G, WLAN and Lte4G. This antenna has an advantage that can cover the three different frequency bands 2.1GHz, 2.4GHz and 2.6GHz through one antenna design. The design and simulations are done using CST Microwave Studio 2014 program. The antenna is designed by using the FR-4 (lossy) substrate with the dielectric constant of er=4.3 and dielectric loss tangent 0.025. The substrate dimensions are the following; Thickness[h] is 1.6mm, Length is 90mm, and Width is 40mm. The ground is designed by using the PEC material with h=0.035mm. The patch is designed by using the copper with h=0.035mm. In the near future, we will fabricate the antenna, which we have designed, and then apply this antenna to the mobile communication system. And we will test this mobile communication system for the diverse environments.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.5
• /
• pp.459-465
• /
• 2020

In this paper, a compact antenna assembly for an amplitude comparison direction-finding(DF) method for a small flight vehicle is presented. Designed antenna assembly consists of four antennas and it is mounted on a radius of 1.45 λ_c where λ_c corresponds to the wavelength of the center frequency. To achieve compactness and robustness of the assembly, the elements are fed by end-launch feeding method and have modified aperture shapes of E- or H-sectoral horns. The feeding part consists of SMA connector, stepped impedance matching structure, and square waveguide of 0.6 λ_c × 0.6 λ_c. To achieve different main beam directions for every antenna which is required condition for amplitude comparison DF method, all apertures of the antennas are inclined and it makes the main beam direction of each antenna to top, bottom, left, and right with respect to the axis of the platform. To verify the validation of DF performance of the presented antenna assembly, amplitude comparison curves using measurement results are presented. The bandwidth of the antennas are above 3.2 % in Ku-band(VSWR ≤ 2:1).

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.3
• /
• pp.220-224
• /
• 2017

In this paper, a method of feeding for the near field beam scanning array antenna with three dimensional focal point has been studied. The conventional array antenna theory is mostly about the far field points. The basic idea is to feed the transmitted signal so that it is in phase at the desired point. In this study, a method is proposed to compensate the phase to have the maximum received power at the point where the measurement point distance is near to the array antenna size. In the proposed method, 11 point source antennas are arrayed in three ways in free space. And the contour map is plotted by calculating the radiation patterns in the three dimensional space and the received signal intensities in the plane within the near space. As a result, it was confirmed that 3 dimensional beam scanning is possible also in the near field of the array antenna.

• Journal of electromagnetic engineering and science
• /
• v.17 no.4
• /
• pp.228-232
• /
• 2017

The radiation properties and fabrication precautions of a 3D printed, electrically small folded spherical meander wire monopole antenna are investigated. The antenna is self-resonant and shows sufficiently high radiation efficiency at an electrical size ka of 0.4, with the radiation quality factor Q approaching the lower physical bound. In antenna fabrication, the possible structural deformation due to gravity is examined before the antenna frame is 3D-printed. The required conductivity is achieved by multiple manual paintings of a silver paste. The radiation efficiency and pattern show very good agreement with the computed expectations, whereas the resonant frequency deviates by 11.8%. The method to minimize such a fabrication error when using 3D printing technology for wire antennas is discussed.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.209-215
• /
• 2017

In this paper, an antenna having 2-axes cross monopulse for Ka band millimeter-wave seeker is designed and antenna performance is verified through vacuum-brazing method for fabrication and measurement. Also, by designing and manufacturing a waveguide circulator the antenna including the circulator is measured. Radiating part of the antenna takes optimized slot lengths and offsets from Elliot's array synthesis procedure using the generic algorithm and feeding part for cross monopulse axes uses the folded waveguide to optimize the S-parameter result. Based on this method, the antenna has 33.3 dBi gain, $3.5^{\circ}{\pm}0.5^{\circ}$ beamwidth, below -23 dB SLL through fabricating and measuring. It is found that antenna characteristics is similar to design results.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.2045-2049
• /
• 2018

An antenna arrays for a satellite navigation systems require more antenna elements to mitigate multiple jamming signals. In order to maintain the small array size while increasing the number of antenna elements, miniaturization technique is essential for antenna design. In this work, an electrically small circular microstrip patch antenna with a 3 dB hybrid coupler is designed as an element antenna, where the 3 dB hybrid coupler can yield the circularly polarized radiation characteristic. The miniaturized element antenna typically has too large capacitance in GPS L1 and GLONASS G1 bands, making it difficult to match with a single stand-alone non-Foster matching circuit (NFMC) in a stable state. Therefore, we propose a new matching technique, referred to as the hybrid matching method, which consists of a NFMC and a passive circuit. This passive tuning circuit manages reactance of antenna elements at an appropriate capacitance without a pole in the operating frequency range. The antenna array is fabricated, and the measured results show a reflection coefficient of less than -10 dB and an isolation of greater than 50 dB. In addition, peak gain of the proposed antenna is increased by 22.3 dB compared to the antenna without the hybrid matching network.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.787-795
• /
• 2003

Three types of array antennas are developed for broadcasting band of Koreasat III. First, the specification of the array antenna is decided. Second, characteristics and advantages of three types of antennas using the radial waveguide characteristics is investigated and discussed. Third, design method fur those antenna is studied to meet antenna specifications, and then antennas are designed and tested. Finally, it is concluded that these types of antennas can be efficiently design compared to both parabola antennas and microstrip array within the limited size.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.3
• /
• pp.43-48
• /
• 2018

Offset parabolic antenna have been widely used for satellite communication system. To locate feedhorn on antenna system, it requires arbitrary structure which forces to fix on system. However, arbitrary scatterer increases sidelobe level of elevation axis. To solve this problem, we need to predict which angle level is increased by arbitrary scatterer simply. Because conventional simulation method takes a long time to simulate parabolic antenna system and needs exclusive software. In this paper we can calculate sidelobe angle simply by using raytracing method, check coincidence between calculated and simulated result and show how arbitrary scatterer affects sidelobe lavel of elevation axis of offset parabolic antenna depending on angle and location of arbitrary structure.