• Korean Journal of Materials Research
• /
• v.2 no.6
• /
• pp.468-476
• /
• 1992

Stress rupture properties and fracture behavior of Ni microalloyed W were studied using direct load creep tester at 100$0^{\circ}C$, 110$0^{\circ}C$ and 120$0^{\circ}C$ in $H_2$. At the same grain size, 15${\mu}$m, the 100hr. stress rupture strength of W-0.4wt% Ni was 23% higher than that of W-0.2wt%Ni due to the grain growth during test. The minimum creep rate of W-0.2wt%Ni was decreased with an increase in initial grain size. By increasing the Ni content of Ni microalloyed W, rupture time was increased owing to the smaller number and size of cavity. All the specimens showed intergranular fracture by grain boundary sliding and nucleation, growth and coalescence of cavities at grain boundary.

• Applied Chemistry for Engineering
• /
• v.35 no.2
• /
• pp.115-121
• /
• 2024

This study analyzed the influence of process variables affecting the thermodynamic equilibrium and fluid dynamics of interfaces such as reverse micelle, salt concentration, interfacial tension, and viscosity of fluids to optimize the microencapsulation process using the W1/O/W2 double emulsion method. The process variable with the greatest impact on encapsulation efficiency was found to be the difference in osmotic pressure between the W1 and W2 phases. It was observed that increasing the salt concentration in the W2 phase or decreasing the ascorbic acid concentration in the W1 phase resulted in higher encapsulation efficiency. Additionally, a larger difference in osmotic pressure led to increased damage to the surface of the microparticles, as confirmed by SEM images. The introduction of reverse micelles, which was anticipated to increase encapsulation efficiency, either had a low contribution or even decreased encapsulation efficiency. The yield of microcapsules was expressed as a universal function, applicable to all process conditions or solution compositions. According to this universal function, no further increase in yield was observed beyond the Ca (capillary number) of approximately 20.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.582-588
• /
• 1997

Synthetic reaction of TAME, ETBE, and MTBE compounds used largely for gasoline octane number enhancer to prevent air pollution was investigated using heteropolyacid catalyst in a fixed bed flow reactor. In the synthetic reaction of TAME, ETBE and MTBE, after hetero atom being replaced with poly atom, the activity of the catalyst, $H_4SiW_{12}O_{40}$ with coordinated bond with W and an hetero atom of Si was the highest among the catalysts tested. Also the activity depended upon the metals replaced which are related to the catalyst acidity. $FeHPW_{12}O_{40}$ and $K_3PM_{o12}O_{40}$ catalysts showed high activity in TAME synthesis, while they were not effective in ETBE and MTBE synthesis. In this study catalysts showing high activity were selected and mixed with equal weight combination of $H_4SiW_{12}O_{40}$ and $Sr_2SiW_{12}O_{40}$ ;$H_4SiW_{12}O_{40}$ and $NaH_2PW_{12}O_{40}$ ; $Fe_{1.5}PW_{12}O_{40}$ and $Mg_2SiW_{12}O_{40}$ ; $Mg_2SiW_{12}O_{40}$ and $Ba_2SiW_{12}O_{40}$. The mixed heteropolyacid catalysts showed higher TBA conversion rate and better selectivity of ETBE and MTBE than the single catalysts.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.2
• /
• pp.4096-4104
• /
• 1976

This experiment was carried out to investigate the efficient turning method which will be able to use every cutting methods, to calculate the width of the center field which must transpose from rotary cutting method to return cutting method, to investigate the effects of L/W and unit field on the operation efficiency. The results are summarized as follows: 1. In case of cutting in the outer field, the efficient turning method is the "$\alpha$" type turning method (half U-shaped turning method) at the first rotation, is the "$\beta$" type turning method (T-shaped turning method) at the second to fourth rotation. 2. In case of cutting in the inner field, the efficient turning method which takes the least turning time is the "a" type turning method ($\Delta$-shaped turning method). 3. The width of the center field (W') changes by the length-width ratio (L/W) and width (W), W' is 9.0m in case that L/W is 2.5 and W is 30m. 4. The larger L/W and area of unit field (A) become, the more operation efficiency (E) increases, and the limits that E is affected signicantly by L/W is 2 to 3.5 and A is within 5,000$m^2$. within 5,000$m^2$.

• Journal of the Microelectronics and Packaging Society
• /
• v.12 no.4 s.37
• /
• pp.345-349
• /
• 2005

Low resistive ($300{\mu}{\Omega}$-cm) W-C-N films have been deposited on tetraethylorthosilicate (TEOS) interlayer dielectric by atomic layer deposition (ALD) with $WF_6-N_2-CH_4$ gas. The exposure cycles of $N_2$ and $CH_4$ are synchronized with pulse plasma. The W-C-N films on TEOS layer follow the ALD mechanism and keep constant deposition rate of 0.2 nm/cycle from 10 to 100 cycles. As a diffusion barrier for Cu interconnection the W-C-N films maintain amorphous phase and Cu inter-diffusion is not occurred even at $800^{\circ}C$ for 30 min.

• Journal of Powder Materials
• /
• v.8 no.4
• /
• pp.245-252
• /
• 2001

Recent remarkable progress in the semiconductor industry has promoted smaller size of semiconductor chips and increased amounts of heat generation. So, the demand for a substrate material to meet both the characteristics of thermal expansion coefficient and heat radiation has been on the increase. Under such conditions, tungsten(W)-copper(Cu) has been proposed as materials to meet both of the above characteristics. In the present study, the W-10wt.%Cu powders were synthesised by the mixing and hydrogen reduction of the starting mixture materials such as W-Cu, $W-CuCl_2$and $WO_3-CuCl_2$ in order to obtain the full densification. The W-10wt.%Cu produced by hydrogen reduction showed the higher interparticle friction than the simple mixed W-10wt%Cu because of the W agglomerates. In the dilatometric analysis the W-10wt.%Cu prepared from the $W-CuCl_2$was largely shrank by heating up $1400^{\circ}C$ at the constant heating rate of $5^{\circ}C$/min. The possibility of application of metal injection molding (MIM) was also investigated for mass production of the complex shaped W-Cu parts in semiconductor devices. The relationship between the temperature of molding die and the pressure of injection molding was analyzed and the heating up stage of 120-$290^{\circ}C$ in the debinding process was controlled for the most suitable MIM condition.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.32 no.1
• /
• pp.42-49
• /
• 1996

The author examined the response of Armorclad rockfish, Sebastes hubbsi [MATSUBARA]to the surface attracting lamps (0.5W, 0.8W, 1W) line in the experimental water tank ($550L{\times}58W{\times}73H$cm). The attraction rate was investigated in accordance with the intervals of lighting and putting out hour (1,5 minute) when each of the attraction lamps was gradually switched off after they were switched on all at once. The results are as follows : 1. Total distribution rate of fish in the illuminated section was 61.6%(mean 12.3%) in case of 1 minute interval, and 41.0%(mean 8.2%) in case of 5 minutes interval. 2. Mean distribution rate of fish at the illuminated section : \circled1Distribution rate at interval of 1 minute were 12.7% in 0.8W, 12.4% in 0.5W and 11.9% in 1 W respectively. \circled2Distribution rate at interval of 5 minutes were 9.0% in 1W, 8.6% in 0.8W and 7.0% in 0.5W respectively. 3. Attraction rates of the last section showed a little increasing as illuminating time elapsed. A difference of attraction rates according to lighting source in 1 minute interval was bigger than that in 5 minute interval. 4. Attraction rate of fish in only last section switched on : \circled1Attraction rate at interval in case of 1 minute were 52.0% in 0.8W, 46.7% in 0.5%W and 45.3% in 1W respectively. \circled2Attraction rate at interval in case of 5 minutes were 32.0% in 1W, 24.0% in 0.8W and 14.7% in 0.5W respectively.

• Journal of the East Asian Society of Dietary Life
• /
• v.27 no.3
• /
• pp.341-347
• /
• 2017

This study was carried out to investigate the characteristics and Vitamin $K_2$ (MK-7) productivity of Cheonggukjang fermented by Bacillus subtilis SRCM100757 depending on the inoculum concentration 0.5% (v/w), 1% (v/w) and 2% (v/w). The lowest moisture content and water activity were $53.7{\pm}0.6%$ and $8.39{\pm}0.09$ after fermentation for 72 hours at 2% (v/w). pH slowly became alkalized during fermentation, but there was no significant difference. Amino nitrogen content increased with time and the highest content was $580.8{\pm}1.9mg%$ after fermentation for 72 hours at 2% (v/w). Lightness (L value) and yellowness (b value) decreased with time, whereas redness (a value) hardly changed. MK-7 contents increased with time at each inoculum concentration. The highest content was $20.47{\pm}1.53$ after fermeatation for 72 hours at 2%(v/w) and there were no significant differences between 1%(v/w) and 2%(v/w) inoculum concentrations.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.28 no.3
• /
• pp.471-479
• /
• 2001

The purpose of this study was to compare the effect of the high intensity halogen light $(850\sim1000mW/cm^2)$ with that of the conventional halogen light $(400mW/cm^2)$ on the hardness of composite resin. Three resin composites (Z-100, 3M, U.S.A. : Tetric Ceram, Vivadent, Liechtenstein; SureFil, Dentsply, U.S.A.) were filed in the stainless steel moulds which were 4mm in diameter and 2, 3, 4, and 5mm in depth, respectively. They were cured under the four different modes : (1) conventional mode, 40 seconds at $400mW/cm^2$; (2) 'ramp' mode, 10 seconds at 100 to $1000mW/cm^2$ plus 10 seconds at $1000mW/cm^2$; (3) 'boost' mode, 10 seconds at $1000mW/cm^2$; and (4) 'standard' mode, 20 seconds at $850mW/cm^2$. The surface hardnesses of the top and the bottom of the resin samples were measured with a microhardness tester (MXT70, Matsuzawa, Japan). The top surface hardness was not significantly different among the curing modes. The bottom surface hardness was generally the highest in the conventional mode and the lowest in the high intensity boost mode. There was no significant difference in the bottom surface hardness between the conventional mode and the high intensity standard mode in 2mm depth. The results suggest that the curing time of the high intensity halogen light $(850mW/cm^2)$ should be at least 20 seconds to produce the equal level of the bottom surface hardness of 2mm resin composite as compared to the hardness produced by the conventional halogen light $(400mW/cm^2)$.

• Journal of the Korean Applied Science and Technology
• /
• v.17 no.2
• /
• pp.67-75
• /
• 2000

Cosmetic industries have recently developed sun-block products, which are composed of W/O or O/W emulsion system. It was very difficult for waterproofing product to show the stability in W/O emulsion with $TiO_{2}$. To enhance the stability of W/O emulsion, it needs to be combined with the water and oil soluble components as the gelling agents. The emulsifiers used in W/O were 3.0% of cetyl dimethicone copolyol, 2.0% of sorbitan sesquioleate as the basic emulsifiers, and 0.6% of quaternium-18 bentonite and 1.5% of dextrin palmitate as stabilizer were used. The content of titanium dioxide was optimized up to 8.0%. Titanium dioxide was used as the UV scattering powder coated with $Al_{2}O_{3}$(UV-sperse T40/TN). The sunscreen cream prepared with W/O emulsion system by using QB and DP showed higher stability than that of W/O emulsion system by using each QB and DP. W/O emulsion from Formula 3 for passing one year was very durable more than F1 and F2. Within W/O emulsion by observing F1, F2 and F3 for one year, F3 was more excellent than F2 and F3 when they were observed at RT, $4^{\circ}C$, $40^{\circ}C$, because F3 used the mixed QB and DP in W/O emulsion. The zeta potential for F1, F2, and F3 after one year were 21, 30 and 43, respectively. From these result F3 was found best stable emulsion. The in-vitro SPF value for F3 was 35 for the initial product at room temperature and also, the in-vitro SPF values of F3 was 32 for after one year. Finally, the mean in-vivo SPF value of 10 volunteers for F3 was 27.3 by the Korea cosmetic association made the rules of SPF.