• ETRI Journal
• /
• v.27 no.3
• /
• pp.312-318
• /
• 2005

Mid-span spectral inversion (MSSI) has to utilize high optical pump power, for its operation principle is based on a nonlinear optical wavelength conversion. In this paper, a low pump-power operation of MSSI-based chromatic dispersion compensation (CDC) has been achieved successfully, for the first time to our knowledge, by introducing a noise pre-reduction scheme in cascaded wavelength conversions with periodically poled $LiNbO_3$ waveguides at a relatively low operation temperature. As preliminary studies, phase-matching properties and operation-temperature dependence of the wavelength converter (WC) were characterized. The WC pumped at 1549 nm exhibited a wide conversion bandwidth of 59 nm covering the entire C-band and a conversion efficiency of -23.6 dB at 11 dBm pump power. CDC experiments were implemented with 2.5 and 10 Gb/s transmission systems over 100 km single-mode fiber. Although it is well-known that the signal distortion due to chromatic dispersion is not critical at a 2.5 Gb/s transmission, the clear recovery of eye patterns was identified. At 10 Gb/s transmission experiments, eye patterns were retrieved distinctly from seriously distorted ones, and notable improvements in bit-error rates were acquired at a low pump power of 14 dBm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.7
• /
• pp.944-950
• /
• 1993

Diodes and GaAs have been commonly used in a mixer design until recently. However, diodes are not preferred to use at the front-end of DBS receiver due to the conversion loss large noise. HEMT has larger conversion gain and better noise characteristics comparing with GaAs MESFET. This paper describes the design procedure, structure, and performance of a mixer, utilizaing HEMT designed by OKI Co. . A mixer configuration in which the local oscillator(LO) signal is applied to the gate is used. When the LO power is 0.01 dBm, the conversion gain of 3.7dB is obtained at IF and the 3 dB bandwidth is 400MMz.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.261-264
• /
• 2005

This paper presents the design of a down-conversion mixer with built-in active balun integrated in a $0.25\;{\mu}m$ pHEMT process. The active balun consists of series-connected common-gate FET and common-source FET. The designed balun achieved broadband characteristics by optimizing gate-width and bias condition for the reduction in parasitic effect. From DC to more than 6GHz, the active balun shows the phase error of less than 3 degree and the gain error of less than 0.4 dB. A single-balanced down-conversion mixer with built-in broadband active balun has been designed with optimum width, load resistor and bias for conversion gain and without any matching component for broadband operating. The designed mixer whose size of including on-chip bias circuit is $1\;mm{\times}1\;mm$ shows the conversion gain of better than 7 dB from 2 GHz to 6 GHz and $P_{1dB}$ of -10 dBm at 5.8 GHz

• International Journal of Industrial Entomology and Biomaterials
• /
• v.9 no.2
• /
• pp.249-254
• /
• 2004

Dietary supplementation of sodium nitrate with different concentrations 50, 100, 200, 500, 700 and 1000 $\mu\textrm{g}$/ml of single, two, three and four feeds to fifth instar larvae of biovoltine NB$_4$D$_2$ race of the silkworm, B. mori resulted in significant increase in the food conversion, conversion rate and conversion efficiency $K_1$ and $K_2$. However, there were significant decrease in the food assimilation, assimilation rate and assimilation efficiency in the sodium nitrate treated groups as compared with that of the corresponding parameters of the carrier control. This indicates that the administration of sodium nitrate may stimulate metabolic activities, thereby influencing conversion of food into body weight in the bivoltine silkworm, B. mori.

• Journal of the Korea Computer Graphics Society
• /
• v.20 no.2
• /
• pp.1-11
• /
• 2014

The quality of 2D-to-3D conversion depends on the accuracy of the assigned depth to scene objects. Manual depth painting for given objects is labor intensive as each frame is painted. Specifically, a human is one of the most challenging objects for a high-quality conversion, as a human body is an articulated figure and has many degrees of freedom (DOF). In addition, various styles of clothes, accessories, and hair create a very complex silhouette around the 2D human object. We propose an efficient method to estimate visually pleasing depths of a human at every frame in a monocular video. First, a 3D template model is matched to a person in a monocular video with a small number of specified user correspondences. Our pose estimation with sequential joint angular constraints reproduces a various range of human motions (i.e., spine bending) by allowing the utilization of a fully skinned 3D model with a large number of joints and DOFs. The initial depth of the 2D object in the video is assigned from the matched results, and then propagated toward areas where the depth is missing to produce a complete depth map. For the effective handling of the complex silhouettes and appearances, we introduce a partial depth propagation method based on color segmentation to ensure the detail of the results. We compared the result and depth maps painted by experienced artists. The comparison shows that our method produces viable depth maps of humans in monocular videos efficiently.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.81-86
• /
• 2003

This paper deals with the performance analysis and design of impulse turbine for OWC type wave energy plant. Numerical analysis was performed using a commercially-available software FLUENT. This parametric study includes the variation of several important parameters such as the number and shape of blades, hub ratio and tip clearance. Since parametric study at various flow coefficients requires considerable amount of computing tim, two-dimensional analysis was employed to find out optimum principal particulars in rather simple manner. Full three-dimensional calculation was also performed for several test cases to confirm the validity of two-dimensional approach. Up to the present stage, tentative result is well demonstrating the usefulness of 2-D analysis.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.5
• /
• pp.1-6
• /
• 2004

This paper deals with the performance analysis and design of impulse turbine for owe type wave energy plant. Numerical analysis is performed using a commercial software FLUENT. This parametric study includes the variation of several important parameters, such as the number and shape of blades, hub ratio, and tip clearance. Since parametric study at various flow coefficients requires a considerable amount of computing time, two-dimensional analysis is employed to find out optimum principal particulars. Full three-dimensional calculations are also performed for several test cases, in order to confirm the validity of the two-dimensional approach. Up to the present stage, tentative results are demonstrated the usefulness of 2-D analysis.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.682-690
• /
• 2012

In this paper, a highly linear self oscillating mixers(SOM) using second harmonic injections are presented. The H-slot defected ground structure(DGS) is designed as a balanced resonator for oscillation in the proposed SOM. Since the H-slot DGS resonator achieves a high Q factor, it is a suitable structure to provide low phase noise for the oscillator. The single balanced mixer is utilized in this work and it provides good LO-RF isolation since balanced LO signals are suppressed at the RF input port. In order to inject the second harmonic of the IF, we propose two different methods using feedback loops. In the first method, IF achieves a 3.08 dB conversion gain at 226 MHz with input power of -20 dBm at 5 GHz RF input signal. The IF achieves 2 dB conversion gain at 423 MHz with the input power of -20 dBm at 5.2 GHz RF input signal in the second method. The measured IMD3s are 61.8 dB and 65 dB for the each method. These SOMs present improved linearity compared to that without the second harmonic injection because IMD3s are improved by 18. dB and 21 dB for each method.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37 no.7A
• /
• pp.545-551
• /
• 2012

In this paper, K-band multi-channel receiver was designed and fabricated for low noise amplification and down conversion to L-band. The fabricated multi-channel receiver incorporates GaAs-HEMT LNA(Low noise amplifier) which provides less than a 2 dB noise figure, IR(Image Rejection) Filter for rejection of image frequency, IR(Image rejection) mixer to reject a image frequency and improve an IMD(Intermodulation Distortion) characteristic. Test results of the fabricated multi-channel receiver show less than a 3.8 dB noise figure, conversion gain of more than 27dB, and IP1dB(Input 1dB Gain Compression Point) of -9.5 dB and over.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2010.11a
• /
• pp.184-187
• /
• 2010

본 논문에서는 움직임 추정(Motion Estimation, ME), 색상 라벨링(Labeling) 그리고 Non-Local means 필터 등을 이용하여 2D 영상을 3D 입체 영상으로 변환하는 기법을 제안한다. 제안하는 기법에서는 프레임 간의 움직임 추정 방법을 사용하여 물체의 움직임 벡터를 추출하며 색상 라벨링 작업을 통해 세밀한 객체를 추출한다. 객체를 추출한 후 영상을 이동시켜서 우영상을 생성한다. 우 영상을 생성하는 과정에서 채워지지 않은 화소들이 발생하는데 전체 화소의 상관도를 고려하는 Non-local means 필터를 사용하여 이 부분을 처리한다. 생성된 우 영상과 원본 영상인 좌 영상으로 비월주사(interlace)하여 최종 3D 입체 영상을 생성한다.