• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2007.04a
• /
• pp.401-404
• /
• 2007

본 논문은 거울 투영을 이용하여 2D의 감정인식 데이터베이스를 3D에 적용 가능하다는 것을 증명한다. 또한, 감정 확률을 이용하여 퍼지 모델링을 기반으로한 얼굴표정을 생성하고, 표정을 움직이는 3가지 기본 움직임에 대한 퍼지이론을 적용하여 얼굴표현함수를 제안한다. 제안된 방법은 거울 투영을 통한 다중 이미지를 이용하여 2D에서 사용되는 감정인식에 대한 특징벡터를 3D에 적용한다. 이로 인해, 2D의 모델링 대상이 되는 실제 모델의 기본감정에 대한 비선형적인 얼굴표정을 퍼지를 기반으로 모델링한다. 그리고 얼굴표정을 표현하는데 기본 감정 6가지인 행복, 슬픔, 혐오, 화남, 놀람, 무서움으로 표현되며 기본 감정의 확률에 대해서 각 감정의 평균값을 사용하고, 6가지 감정 확률을 이용하여 동적 얼굴표정을 생성한다. 제안된 방법을 3D 인간형 아바타에 적용하여 실제 모델의 표정 벡터와 비교 분석한다.

• Korean Journal of Agricultural Science
• /
• v.48 no.3
• /
• pp.515-526
• /
• 2021

The frequency of typhoons and torrential rainfalls has increased due to climate change, and the concurrent risk of breakage of dams and reservoirs has increased due to structural aging. To cope with the risk of dam breakage, a more accurate emergency action plan (EAP) must be established, and more advanced technology must be developed for the prediction of flooding. Hence, the present study proposes a method for establishing a more effective EAP by performing flood and inundation analyses using one- and two-dimensional models. The probable maximum flood (PMF) under the condition of probable maximum precipitation (PMP) was calculated for the target area, namely the Gyeong-cheon reservoir watershed. The breakage scenario of the Gyeong-cheon reservoir was then built up, and breakage simulations were conducted using the dam-break flood forecasting (DAMBRK) model. The results of the outflow analysis at the main locations were used as the basis for the one-dimensional (1D) and two-dimensional (2D) flood inundation analyses using the watershed modeling system (WMS) and the FLUvial Modeling ENgine (FLUMEN), respectively. The maximum inundation area between the Daehari-cheon confluence and the Naeseong-cheon location was compared for each model. The 1D flood inundation analysis gave an area of 21.3 km², and the 2D flood inundation analysis gave an area of 21.9 km². Although these results indicate an insignificant difference of 0.6 km² in the inundation area between the two models, it should be noted that one of the main locations (namely, the Yonggung-myeon Administrative and Welfare Center) was not inundated in the 1D (WMS) model but inundated in the 2D (FLUMEN) model.

• Journal of Computational Design and Engineering
• /
• v.2 no.1
• /
• pp.67-72
• /
• 2015

Recently, along with the improvements of geometry modeling methods using sketch-based interface, there have been a lot of developments in research about generating surface model from 3D curves. However, surfacing a 3D curve network remains an ambiguous problem due to the lack of geometric information. In this paper, we propose a new algorithm for estimating the normal vectors of the 3D curves which accord closely with user intent. Bending energy is defined by utilizing RMF(Rotation-Minimizing Frame) of 3D curve, and we estimated this minimal energy frame as the one that accords design intent. The proposed algorithm is demonstrated with surface model creation of various curve networks. The algorithm of estimating geometric information in 3D curves which is proposed in this paper can be utilized to extract new information in the sketch-based modeling process. Also, a new framework of 3D modeling can be expected through the fusion between curve network and surface creating algorithm.

• Fibers and Polymers
• /
• v.4 no.2
• /
• pp.77-83
• /
• 2003

The cell modeling homogenization method to derive the constitutive equation considering the microstructures of the fiber reinforced composites has been previously developed for composites with simple microstructures such as 2D plane composites and 3D rectangular shaped composites. Here, the method has been further extended for 3D circular braided com-posites, utilizing B-spline curves to properly describe the more complex geometry of 3D braided composites. For verification purposes, the method has been applied for orthotropic elastic properties of the 3D circular braided glass fiber reinforced com-posite, in particular for the tensile property. Prepregs of the specimen have been fabricated using the 3D braiding machine through RTM (resin transfer molding) with epoxy as a matrix. Experimentally measured uniaxial tensile properties agreed well with predicted values obtained for two volume fractions.

• Korean Journal of Computational Design and Engineering
• /
• v.19 no.1
• /
• pp.41-49
• /
• 2014

For the reuse of the existing 3D block model of a ship, we analyze the hull modeling process using AVEVA Marine which is a representative CAD (Computer-Aided Design) system for the shipbuilding. In the AVEVA Marine environment where the design engineer makes 3D model on the 2D view that is so-called 2.5D, it cannot be possible to copy to reuse the block model just simply copying the 3D feature model itself like in the general mechanical CAD system or Smart Marine 3D which are on the basis of the 3D model representation. In this paper, we analyze the scheme file where the 3D model is defined in AVEVA Marine so that we develop the program for the block copy and the translation using this scheme file. It is significant that this program can be immediately available as a real-world application on the AVEVA Marine environment.

• International conference on construction engineering and project management
• /
• 2007.03a
• /
• pp.337-345
• /
• 2007

Nowadays, it is convenient to use 3D modeling tools for general planning before construction. Normally, a 3D model is built with 3D CAD such as 3D Studio Max, Maya, etc. or simply with AutoCAD. All these software packages are effective in building 3D models but difficult to use, because many provided functions and tools require prior knowledge to build both 2D and 3D designs. Moreover, the traditional method of building 3D models is most time-consuming as experienced operators and manual input are required. Therefore, how to minimize the building time of 3D models and provide easy-to-use functions for users who are not familiar with 3D modeling becomes important. In this paper, the VisualLISP programming language is used to create a convenient tool for efficient generation of 3D components for the AutoCAD environment. This tool will be demonstrated with the generation of a 3D sluice, an artificial passage for water fitted with a valve or gate to stop or regulate water flow. With the tool, users only need to enter the parameters of a sluice in the edit box and the 3D model will be automatically generated in a few seconds. By changing parameters in the edit box and pressing the "OK" button, a new 3D sluice model will be generated in a short while.

• Korean Journal of Optics and Photonics
• /
• v.14 no.3
• /
• pp.306-311
• /
• 2003

In this paper, we modeled the incident beam in order to analyze and evaluate the optical thin film device for wavelength division multiplexing in optical telecommunication network. As applied ray tracing method to the optical path, we were compared the accuracy of coupling efficiency simulated by two modeling methods. In the results of sinulation, ceil modeling method was preferred to annual modeling method in micro-optic device because of accuracy for coupling efficiency and Gaussian intensity distribution. In the results of optimal simulation for optical device using thin film filter, the distance (d1) between optical fiber and GRIN lens, the distance (d2) between GRIN lens and thin film filter and the coupling efficiency were 0.24 mm, 0.25 mm and -0.11 ㏈ respectively. As d2 was displaced at 0.25 mm and d1 was varied in order to evaluate the optimal value, d1 and maximum coupling efficiency were 0.24 mm and -0.35㏈, respectively. Then the results of experiment were corresponded to that of optimal simulation by cell modeling and it was possible to analyze the performance for optical device using thin film filter by the simulation.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.2
• /
• pp.93-101
• /
• 2021

Recently, with the urban redevelopment and the spread of the planned cities, there is increasing interest in the wind environment, which is related not only to design of buildings and landscaping but also to the comfortability of pedestrians. Numerical analysis for wind environment prediction is underway in many fields, such as dense areas of high-rise building or composition of the apartment complexes, a precisive 3D building model is essentially required in this process. Many studies conducted for wind environment analysis have typically used the method of creating a 3D model by utilizing the building layer included in the GIS (Geographic Information System) data. These data can easily and quickly observe the flow of atmosphere in a wide urban environment, but cannot be suitable for observing precisive flow of atmosphere, and in particular, the effect of a complicated structure of a single building on the flow of atmosphere cannot be calculated. Recently, drone photogrammetry has shown the advantage of being able to automatically perform building modeling based on a large number of images. In this study, we applied photogrammetry technology using a drone to evaluate the flow of atmosphere around two buildings located close to each other. Two 3D models were made into an automatic modeling technique and manual modeling technique. Auto-modeling technique is using an automatically generates a point cloud through photogrammetry and generating models through interpolation, and manual-modeling technique is a manually operated technique that individually generates 3D models based on point clouds. And then the flow of atmosphere for the two models was compared and analyzed. As a result, the wind environment of the two models showed a clear difference, and the model created by auto-modeling showed faster flow of atmosphere than the model created by manual modeling. Also in the case of the 3D mesh generated by auto-modeling showed the limitation of not proceeding an accurate analysis because the precise 3D shape was not reproduced in the closed area such as the porch of the building or the bridge between buildings.

• Korean Journal of Computational Design and Engineering
• /
• v.13 no.2
• /
• pp.109-120
• /
• 2008

ISO 10303-112 is an integrated application resource of ISO 10303, commonly known as STEP, and specifies the procedural_sketch schema. The ISO 10303-112 provides general resources for the representation of modeling commands for the exchange of procedurally represented 2D CAD models. Procedural models have the advantage of being easy to edit, simply by changing values of parameters of their constructional operations. Such models are said to embody design intent, in the sense that modifications to them conform to the method of creation used by their original creator, and they also comply with any constraints implied by the particular constructional operations used. This paper introduces the development and standardization process of the ISO 10303-112, and describes the concept of procedural 2D CAD modeling, the way to represent the procedural 2D CAD models in STEP and the harmonization with other STEP resources.

• Journal of Korean Society for Geospatial Information Science
• /
• v.24 no.2
• /
• pp.71-78
• /
• 2016

After the 'Guidelines for the preservation of digital heritage' were published by UNESCO, interests in the fabrication of digital cultural heritage have been increasing throughout the world. The present study was intended to fabricate digital cultural heritages for existing cultural properties using the reverse engineering technology and obtain two-dimensional drawings. Jinju Castle Gongbukmun, which is a cultural property, was selected as a study subject and 3D modeling of Jinju Castle Gongbukmun was conducted by implementing 3D scanning and processing the point cloud data. Using the Gongbukmun 3D model (3D-Gongbukmun) made as such, requirements as a digital heritage were reviewed and 2D drawings of Gongbukmun such as front views, ground plans, and side views could be prepared.