• Investigative Magnetic Resonance Imaging
• /
• 제20권2호
• /
• pp.81-87
• /
• 2016

Purpose: To analyze the feasibility of three-dimensional (3D) diffusion-weighted (DW) PSIF (reversed FISP [fast imaging with steady-state free precession]) sequence in order to evaluate peripheral nerves in the elbow. Materials and Methods: Ten normal, asymptomatic volunteers were enrolled (6 men, 4 women, mean age 27.9 years). The following sequences of magnetic resonance images (MRI) of the elbow were obtained using a 3.0-T machine: 3D DW PSIF, 3D T2 SPACE (sampling perfection with application optimized contrasts using different flip angle evolution) with SPAIR (spectral adiabatic inversion recovery) and 2D T2 TSE (turbo spin echo) with modified Dixon (m-Dixon) sequence. Two observers used a 5-point grading system to analyze the image quality of the ulnar, median, and radial nerves. The signal-to-noise ratio (SNR) and contrast-to-noise ratio (CNR) of each nerve were measured. We compared 3D DW PSIF images with other sequences using the Wilcoxon-signed rank test and Friedman test. Inter-observer agreement was measured using intraclass correlation coefficient (ICC) analysis. Results: The mean 5-point scores of radial, median, and ulnar nerves in 3D DW PSIF (3.9/4.2/4.5, respectively) were higher than those in 3D T2 SPACE SPAIR (1.9/2.8/2.8) and 2D T2 TSE m-Dixon (1.7/2.8/2.9) sequences (P < 0.05). The mean SNR in 3D DW PSIF was lower than 3D T2 SPACE SPAIR, but there was no difference between 3D DW PSIF and 2D T2 TSE m-Dixon in all of the three nerves. The mean CNR in 3D DW PSIF was lower than 3D T2 SPACE SPAIR and 2D T2 TSE m-Dixon in the median and ulnar nerves, but no difference among the three sequences in the radial nerve. Conclusion: The three-dimensional DW PSIF sequence may be feasible to evaluate the peripheral nerves around the elbow in MR imaging. However, further optimization of the image quality (SNR, CNR) is required.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.468-475
• /
• 2018

In medical ultrasound imaging, frequency-dependent attenuation downshifts and reduces a center frequency and a frequency bandwidth of received echo signals, respectively. This causes considerable errors in quadrature demodulation (QDM), result in lowering signal-to-noise ratio (SNR) and contrast resolution (CR). To address this problem, adaptive dynamic QDM (ADQDM) that estimates center frequencies along depth was introduced. However, the ADQDM often fails when imaging regions contain hypoechoic regions. In this paper, we introduce a valid region-based ADQDM (VR-ADQDM) method to reject the misestimated center frequencies to further improve SNR and CR. The valid regions are regions where the center frequency decreases monotonically along depth. In addition, as a low-pass filter of QDM, Gaussian wavelet based dynamic filtering was adopted. From the phantom experiments, average SNR improvements of the ADQDM and the VR-ADQDM over the traditional QDM were 1.22 and 5.27 dB, respectively, and the corresponding maximum SNR improvements were 2.56 and 10.58 dB. The contrast resolution of the VR-ADQDM was also improved by 0.68 compared to that of the ADQDM. Similar results were obtained from in vivo experiments. These results indicate that the proposed method would offer promises for imaging technically-difficult patients due to its capability in improving SNR and CR.

• Biomedical Engineering Letters
• /
• 제8권4호
• /
• pp.383-392
• /
• 2018

For prompt gamma ray imaging for biomedical applications and environmental radiation monitoring, we propose herein a multiple-scattering Compton camera (MSCC). MSCC consists of three or more semiconductor layers with good energy resolution, and has potential for simultaneous detection and differentiation of multiple radio-isotopes based on the measured energies, as well as three-dimensional (3D) imaging of the radio-isotope distribution. In this study, we developed an analytic simulator and a 3D image generator for a MSCC, including the physical models of the radiation source emission and detection processes that can be utilized for geometry and performance prediction prior to the construction of a real system. The analytic simulator for a MSCC records coincidence detections of successive interactions in multiple detector layers. In the successive interaction processes, the emission direction of the incident gamma ray, the scattering angle, and the changed traveling path after the Compton scattering interaction in each detector, were determined by a conical surface uniform random number generator (RNG), and by a Klein-Nishina RNG. The 3D image generator has two functions: the recovery of the initial source energy spectrum and the 3D spatial distribution of the source. We evaluated the analytic simulator and image generator with two different energetic point radiation sources (Cs-137 and Co-60) and with an MSCC comprising three detector layers. The recovered initial energies of the incident radiations were well differentiated from the generated MSCC events. Correspondingly, we could obtain a multi-tracer image that combined the two differentiated images. The developed analytic simulator in this study emulated the randomness of the detection process of a multiple-scattering Compton camera, including the inherent degradation factors of the detectors, such as the limited spatial and energy resolutions. The Doppler-broadening effect owing to the momentum distribution of electrons in Compton scattering was not considered in the detection process because most interested isotopes for biomedical and environmental applications have high energies that are less sensitive to Doppler broadening. The analytic simulator and image generator for MSCC can be utilized to determine the optimal geometrical parameters, such as the distances between detectors and detector size, thus affecting the imaging performance of the Compton camera prior to the development of a real system.

• 제어로봇시스템학회논문지
• /
• 제21권12호
• /
• pp.1130-1135
• /
• 2015

The bond pull test is the most widely used technique for the evaluation and control of wire bond quality. The wire being tested is pulled upward until the wire or bond to the die or substrate breaks. The inspector test strength of wire by manually and it takes around 3 minutes to perform the test. In this paper, we develop a 3D vision system to measure 3D position of wire. It gives 3D position data of wire to move a hook into wires. The 3D measurement method to use here is a confocal imaging system. The conventional confocal imaging system is a spot scanning method which has a high resolution and good illumination efficiency. However, a conventional confocal systems has a disadvantage to perform XY axis scanning in order to achieve 3D data in given FOV (Field of View) through spot scanning. We propose a method to improve a parallel mode confocal system using a micro-lens and pin-hole array to remove XY scan. 2D imaging system can detect 2D location of wire and it can reduce time to measure 3D position of wire. In the experimental results, the proposed system can measure 3D position of wire with reasonable accuracy.

• Journal of information and communication convergence engineering
• /
• 제12권2호
• /
• pp.83-88
• /
• 2014

The simultaneous suppression of sidelobes and the sharpening of the central peak in the process of diffraction pattern detection based on asymmetric apodization have been investigated. Asymmetric apodization is applied to a semicircular array of two-dimensional (2D) aperture functions, which is a series of 'coded-phase arrays of semicircular rings randomly distributed over the central circular region of a pupil function' and is similar to that used in the field of diffractive optics. The point spread function (PSF) of an imaging system with asymmetric apodization of the discrete type has been found to possess a good side with suppressed sidelobes, whereas its bad side contains enhanced sidelobes. Further, the diffracted field characteristics are obtained in the presence of these aperture functions. Asymmetric apodization is helpful in improving the performance of the optical gratings or 2D arrays used in real-time imaging techniques.

• 대한방사선기술학회지:방사선기술과학
• /
• 제38권4호
• /
• pp.389-394
• /
• 2015

의료영상 검사는 정보기술 및 의료장비의 발달로 인체의 해부학적 구조를 묘사하는 능력이 날로 발전하고 있다. 그러나 상지회전이 필요한 어깨관절 의료영상 검사에서는 인체구조의 복잡성으로 정확한 자세유지가 의료영상의 진단적 가치에 매우 중요하다. 자기공명검사의 경우 긴 검사시간과 고정된 자세가 필요해 검사자의 노력과 환자의 의지만으로 재현성 있는 검사가 불가능하다. 이에 상지회전과 정량적 각도가 가능한 보조기구를 개발하여 진단적 가치가있는 의료영상 검사를 하고자하였다. 본 연구는 선행 연구의 결과를 바탕으로 보조기구를 제작하였으며, 공학용 프로그램인 CATIA 프로그램으로 3차원 모델링을 설계하여, 3D프린터로 최종 완성된 보조기구를 제작하였다. 사용된 3D 프린터는 Stratasys Objet350 Connex 모델이며, 재질은 광경화성 수지를 사용하였다. 완성된 보조기구의 크기는 $120{\times}150{\times}190mm$이며, 손잡이부의 내경은 125.9 mm 로 디자인되었다. 보조기구는 총 4개의 부품으로 바디부(외부), 손잡이부(내부), 고정단자, 연결부로 구성되었으며 바디부와 손잡이부는 원활한 회전이 가능하도록 2.1 mm의 유격이 유지되도록 하였다. 손잡이부에는 360o 눈금선을 표시하여 환자마다 관찰에 필요한 회전각도를 기록할 수 있도록 하여 추적검사나 양쪽검사에 적용할 수 있도록 하였다.

• 대한방사성의약품학회지
• /
• 제2권2호
• /
• pp.73-83
• /
• 2016

Imaging hypoxia using positron emission tomography (PET) is of great importance for cancer therapy. [$^{18}F$] Fluoromisonidazole (FMISO) was the first PET agent used for imaging tumor hypoxia. Various radiolabeled nitroimidazole derivatives such as [$^{18}F$]fluoroerythronitroimidazole (FETNIM), [$^{18}F$]1-${\alpha}$-D-(2-deoxy-2-fluoroarabinofuranosyl)-2-nitroimidazole(FAZA), 2-(2-nitroimidazol-1-yl)-N-(3,3,3-[18F]-trifluoropropyl)acetamide ([$^{18}F$]EF-3), [$^{18}F$]2-(2-nitro-1H-imidazol-1-yl)-N-(2,2,3,3,3-pentafluoropropyl) acetamide (EF-5), 3-[$^{18}F$]fluoro-2-(4-((2-nitro-1H-imidazol-1-yl)methyl)-1H-1,2,3,-triazol-1-yl)-propan-1-ol ([$^{18}F$]HX-4), and [$^{18}F$]fluoroetanidazole (FETA) were developed successively. However, these imaging agents still produce PET images with limited resolution; the lower blood flow in hypoxic tumors compared to normoxic tumors results in low uptake of the agents in hypoxic tumors. Thus, the development of better imaging agents is necessary.

• 한국정보처리학회논문지
• /
• 제5권12호
• /
• pp.3275-3284
• /
• 1998

본 논문에서는 각종 단층 촬영 의료영상 장비로 촬영한 2차원 단면화상 데이터들을 차원 재구성 알고리즘을 사용하여 3차원 영상으로 재구성한 다음, 웹 서버의 데이터베이스에 저장하고 관리하며, 인터넷 가상현실 표준언어인 VRML(Virtual Reality Modeling Language)로 표현된 3차원 의료영상을 비롯한 각종 의료영상 정보를 웹브라우저를 사용하여 검색해 볼 수 있는 의료영상정보시스템(Medical Image Information System)에 관하여 기술한다. 본 연구를 통하여 개발한 의료영상정보시스템에서는 단층 촬영된 2차원 단면화상을 처리한 다음, 3차원 의료 영상을 생성하기 위하여 표면기반 랜더링 방법(Surface-based Rendering Method)을 사용하였다. 인터넷을 통하여 전송되는 영상파일의 크기를 줄이기 위하여 삼각형 매쉬(Triangle Meshes)을 이루는 다각형의 개수를 줄이는 알고리즘을 사용하며, 3차원 의료영상 데이터의 크기를 약 50%이상 줄일 수 있다. 아울러, 3차원 영상 데이터 파일을 압축을 하게 되면 파일의 크기를 80%이상 줄일 수 가 있으므로 웹상에서 신속하게 3차원 의료영상 데이터를 검색할 수 있고, 의료영상을 VRML을 사용하여 표현하므로 고성능의 그래픽 카드가 없는 일반 PC에서도 인터넷을 통하여 디스플레이 할 수 있다. 또한, CGI(Common Gateway Interface)방식을 사용하여 서버의 데이터베이스에 저장되어 있는 CT(Computerized Tomography), MRI(Magnetic Resonance Imaging), PET(Positron Emission Tomography), SPECT(Single Photon Emission Computed Tomography)등의 단층 촬영 장비로 촬영한 다양한 종류의 디지털 의료영상을 사용자에게 의료영상정보시스템을 통하여 2차원 단면화상 또는 3차원 영상으로 표현하여 보여주고, 환자에 관한 각종 정보와 진단정보 등을 신속하게 제공한다. 본 논문에서 제안하는 의료영상정보시스템은 초고속 정보통신 망을 통하여 원격의료시스템을 구축하는데 활용될 수 있을 것이다.

• 한국광학회지
• /
• 제23권5호
• /
• pp.189-196
• /
• 2012

플로팅 광학계는 초점 맞춤 시, 2개 이상의 군이 움직이는 광학계를 의미한다. 카메라 광학계에서는 매크로 렌즈와 같이 배율 변화가 큰 광학계에 주로 채용된다. 플로팅 광학계도 가공 및 조립 오차로 인해 무한대단 및 매크로단의 초점위치가 촬상소자의 결상면과 일치하지 않는다. 그러므로 제조공정상에서 이러한 BWD(Back Working Distance) 차이를 최소화하는 초점 조정을 해야 한다. 본 논문에서는 플로팅 광학계의 각 군들의 이동량을 결정하기 위하여 초점 조정에 필요한 캠 회전각을 계산하고, 초점조정에 따른 플로팅 광학계의 최대 배율도 보정하는 수치해석 방법을 제안하였다. 그리고 이를 이용하여 대칭형 공차를 갖는 플로팅 광학계의 제조 오차를 고려한 초점 조정에 필요한 캠 회전각의 분포를 통계학적으로 계산하여 캠 회전각의 허용 범위를 결정하는 방법도 제안하였다.

• 한국광학회지
• /
• 제22권5호
• /
• pp.230-238
• /
• 2011

디지털 일안 반사식 카메라 또는 콤팩트 시스템 카메라용의 교환렌즈용 줌 광학계는 화각과 제품 사양에 따라 여러 가지 형태 가 있으므로, 하나의 AF(auto-focus)군으로만 줌 렌즈의 광각단과 망원단 2곳에서 상면이동의 보정(즉, 핀트 조정)이 불가능한 경우가 발생한다. 또한 줌 광학계의 광각단과 망원단 2곳에서의 후초점거리(back focal length, BFL)가 설정된 BFL 설계값과 일치하도록 조정하기 위해서는 적어도 2곳에서 핀트 조정을 해야 한다. 본 논문에서는 이러한 광학계에 대한 종민감도의 개념을 사용한 핀트 조정의 계산 방법에 대해 제안하고, 이 광학계에 대해 핀트 조정의 조정량 한계를 통계적 분석을 통하여 계산했다.