• Structural Engineering and Mechanics
• /
• 제50권1호
• /
• pp.105-119
• /
• 2014

This study presents a steel container crane movement analysis and assessment based on structural health monitoring (SHM). The accelerometers are used to monitor the dynamic crane behavior and a 3-D finite element model (FEM) was designed to express the static displacement of the crane under the different load cases. The multi-input single-output nonlinear autoregressive neural network with external input (NNARX) model is used to identify the crane dynamic displacements. The FEM analysis and the identification model are used to investigate the safety and the vibration state of the crane in both time and frequency domains. Moreover, the SHM system is used based on the FEM analysis to assess the crane behavior. The analysis results indicate that: (1) the mean relative dynamic displacement can reveal the relative static movement of structures under environmental load; (2) the environmental load conditions clearly affect the crane deformations in different load cases; (3) the crane deformations are shown within the safe limits under different loads.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1382-1387
• /
• 2010

A 3D FEM numerical analysis was performed to observe the changes of supporting system of a old 1-lane tunnel when it is enlarged to 2-lane, 3-lane and 4-lane. The standard Type-III supporting pattern was applied to the new tunnel because the ground was assumed as Type-III. The observation was carried out at the middle supporting system of the old 1-lane tunnel alignment. The results shows that the changes of old tunnel supporting system began when the new tunnel was excavated at 2D(D is the equivalent diameter of 1-lane tunnel) behind of the observation place and became very rapid from 1D.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제2B권4호
• /
• pp.162-167
• /
• 2002

This paper presents the dynamic analysis method for a slotless permanent magnet linear synchronous motor (PMLSM) using the 3-D space harmonic method. Instantaneous emf and thrust are considered by movement of the PM and instantaneous armature current instead of $K_E$ (back-emf constant) and $K_F$(thrust force constant) for accurate results. The results of magnetic field distribution, back-emf, inductance, and thrust are in agreement with 2-D FEM and experimental results. To confirm the validity of this method, the calculated results are compared to measured ones.

• 해양환경안전학회지
• /
• 제19권4호
• /
• pp.410-415
• /
• 2013

음향 표적강도는 잠수함의 생존성을 보장하기 위한 중요한 설계 고려 요소이다. 잠수함이 대형화 됨에 따라 음향 표적강도 저감을 위한 대표적인 방법으로 알베리히 무반향 코팅재가 널리 사용되고 있다. 본 논문에서는 규칙적으로 배열된 알베리히 무반향 코팅재 단위 셀에 대해 유한요소법을 이용하여 음압 투과반사 계수를 해석하였다. 해석 결과는 문헌의 실험결과와 비교 검증하였다. 또한, 잠수함의 음향 표적강도 계산시 해석된 코팅재의 입력 임피던스를 이용하여 반사계수를 고려하였다. 마지막으로 알베리히 무반향 코팅재 적용에 따른 음향 표적강도 감소 효과(Case 1: 10dB, Case 2: 6dB)를 확인하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1085-1086
• /
• 2011

This paper proposes a structure optimal design of 2-phase BLDC motor. In order to improve the characteristics of the BLDC motor such as the efficiency, average torque, the Kriging method and genetic algorithm are utilized. In addition, the result of the optimal model were compared with the initial model and verified by 2D FEM.

• 대한기계학회논문집A
• /
• 제33권9호
• /
• pp.963-968
• /
• 2009

This paper deals with shrink fit analysis of rotor by 2D cross-section, 2D axis-symmetry, and 3D FEM model. And this paper presents 2nd order approximation function of thermal expansion displacement by design variables (shape dimension, heating temperature, sleeve length, interference etc.), table of orthogonal array and RSM(response surface methodology). The possibility of the rotor with shrink fit is evaluated by thermal expansion displacement. If thermal expansion displacement is larger than interference, shrink fit enable to make the rotor. 2D axis-symmetry model and 3D model are more reasonable than 2D cross-section model, because stress and strain is different along length of shaft.

• Ocean Systems Engineering
• /
• 제1권4호
• /
• pp.317-336
• /
• 2011

A time domain finite element based method is employed to analyze wave radiation by multiple cylinders. The nonlinear free surface and body surface boundary conditions are satisfied based on the perturbation method up to the second order. The first- and second-order velocity potential problems at each time step are solved through a finite element method (FEM). The matrix equation of the FEM is solved through an iteration and the initial solution is obtained from the result at the previous time step. The three-dimensional (3D) mesh required is generated based on a two-dimensional (2D) hybrid mesh on a horizontal plane and its extension in the vertical direction. The hybrid mesh is generated by combining an unstructured grid away from cylinders and two structured grids near the cylinder and the artificial boundary, respectively. The fluid velocity on the free surface and the cylinder surface are calculated by using a differential method. Results for various configurations including two-cylinder and four-cylinder cases are provided to show the mutual influence due to cylinders on the first and second waves and forces.

• Journal of Electrical Engineering and Technology
• /
• 제11권6호
• /
• pp.1628-1633
• /
• 2016

This paper derives an effective shape of the ferromagnetic pole pieces (low-speed rotor) for the reduction of transmission torque ripple in a magnetic-geared machine based on a Box-Behnken design (BBD). In particular, using a non-linear finite element method (FEM) based on 2-D numerical analysis, we conduct a numerical investigation and analysis between independent variables (selected by the BBD) and reaction variables. In addition, we derive a regression equation for reaction variables according to the independent variables by using multiple regression analysis and analysis of variance (ANOVA). We assess the validity of the optimized design by comparing characteristics of the optimized model derived from a response surface analysis and an initial model.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.244-246
• /
• 1996

In an controlled electric machine, the variations of motor parameters such as stator and rotor time constant are caused by the temperature rise, thus it is needed to calculate the accurate parameter through the dynamic characteristic analysis considering the temperature variation. In this paper, the dynamic characteristic analysis method of vector controlled LIM is proposed using coupled magnetic & thermal 2D FEM taking into account the movement.

• 소성∙가공
• /
• 제15권7호
• /
• pp.504-511
• /
• 2006

The drawability of AZ31B magnesium sheet is estimated at various temperatures($200,\;250,\;300,\;350\;and\;400^{\circ}C$), and forming speed(20, 50, 100mm/min), thickness(0.5, 0.8, 1.0, 1.4mm). The deep drawing process of circular cup and square cup were used in forming experiments. Experimental and FEM analysis are performed to investigate drawability and affection of controlled blank holding force. Through the controlled blank holding force, drawability was improved. Limit drawing ratio is increased from 2.1 to 3.0 in circular cup drawing and change of thickness is decreased from 16.3 to 6.9%. This result is verified by FEM analysis. Through the observation of microstructure, the main cause is investigated as a quantity of the dynamic recrystallization.