• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.238-242
• /
• 2004

The paper describes an automatic frequency control current-fed inverter for forging applications. The IGBT in series with diodes as its switching devices in the inverter circuit which is of full-bridge type. The operating frequency is automatically tracked to maintain a small constant leading phase angle when load parameters change. The load voltage is controlled to protect the switches. The output power can be adjusted by varying the input current from phase controlled rectifiers which is a part of current source. The system has been operated at 15-17 kHz. The output power transferred to the load is 1,595 watts. It can heat the steel work pieces with 15 mm diameter and 120 mm long from room temperature to approximately 1100 $^{\circ}C$ within 20 seconds with 0.97 leading power factor on the input side.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.11
• /
• pp.48-55
• /
• 2016

Ambient-light sensor system, which changes the brightness of a display as ambient light change, was studied to reduce the power consumption of the mobile applications such as note PC, tablet PC and smart phone. The ambient-light sensor system should be integrated on a display panel to improve the complexity and cost of mobile applications, so the ambient-light sensor and readout circuit was integrated on a display panel using low-temperature poly-silicon thin film transistors (LTPS-TFT). We proposed the new compensation method to correct the panel-to-panel variation of the ambient-light sensors, without additional equipment. We designed and investigated the new readout circuit with the proposed compensation method and the analog-to-digital converter for the final digital output of ambient light. The readout circuit has very simple structure and control timing to be integrated with LTPS-TFT, and the input luminance ranges from 10 to 10,000 lux. The readout rate is 100 Hz, and maximum differential non-uniformity with 20 levels of the final output below 0.5 LSB.

• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1085-1092
• /
• 2001

The high efficient AC powder EL devices classified by low cost and low power consumption type fabricated using screen printing method with film thickness and organic binder. Brightness and current density were measured at frequency range of 400Hz∼1kHz and voltage range of 50∼300V$\_$rms/ to estimate optoelectrical properties of AC powder EL devices, respectively. Frequency generator was used as system producing frequency and voltage of a sine wave. Also brightness and current density were measured by luminometer and multimeter. In the case of low cost type AC powder EL device, brightness and current density were about 43 cd/m$^2$and 20$\mu$A/cm$^2$when the thickness of phosphor and dielectric layer was 45∼50$\mu$m under no addition of plasticizer respectively. In the case of low power consumption type AC powder EL device, brightness and current density were about 74 cd/m$^2$and 30∼40$\mu$A/cm$^2$when the thickness of phosphor and dielectric layer was 45∼50$\mu$m and 15∼20$\mu$m under addition of 15wt% plasticizer respectively. Also, AC powder EL device fabricated in this study showed absolutely excellent characteristics as the lifetime was longer than products of other company.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2021.10a
• /
• pp.630-633
• /
• 2021

Microphones can convert received voice signals to electric signals. They have been widely used in various industries such as radios, smart devices and vehicles. Recently, the demands for small size and high sensitive microphones are increased according to the minimization of wireless earphone with the development of smart phone. A MEMS system is a good candidate for an ultra-small size microphone of a next generation and a read out IC for high sensitive MEMS sensor is researched from many industries and academies. Since the microphone system has a high sensitivity from environment noise and electric system noise, the system requires a low noise power supply and some low noise design techniques. In this paper, a low noise LDO is presented for small size MEMS microphone systems. The input supply voltage of the LDO is 1.5-3.6V, and the output voltage is 1.3V. Then, it can support to 5mA in the light load condition. The integrated output noise of proposed LDO form 20Hz to 20kHz is about 1.9uV. These post layout simulation results are performed with TSMC 0.18um CMOS technology and the size of layout is 325㎛ × 165㎛.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.330-333
• /
• 1997

In this paper, we designed a low power and small-sized, light weighted intelligent ambulatory monitoring system using a flash memory card. The system's hardware specifications are as follows: 2 channels, 8bit/250Hz sampling rate, 20M byte storage capacity, a single-chip microcontroller (68HC11E9). To easily interface with PC based system, FFS(Flash File System) was used. We obtained the QRS detection rate of 99.14 through the evaluation with MIT/BIH database.

• Journal of Sensor Science and Technology
• /
• v.20 no.1
• /
• pp.46-52
• /
• 2011

In this paper, the swept source-optical coherence tomography system using frequency domain mode locked(FDML) laser has realized. The FDML swept source laser showed 55.03 kHz sweeping speed, 125 nm sweeping range, and 9 mW output optical power, which are the superiority of FDML laser compared to previous swept source lasers. Also, through the cross-sectional image captured at 5 frames per second for a mirror, a 1 mm-thickness glass plate, and a thumb bottom, the performance of the system has demonstrated.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.8
• /
• pp.426-432
• /
• 2004

This paper presents a systematic approach of measurement, modeling and analysis of grounding system impedance in the field of lightning protection system and intelligent power equipments. The measurement and analysis system of ground impedance is based on a computer aided technique. The magnitude and phase of ground impedance were determined by the novel measurement and analysis using the revised fall-of-potential method. The ground impedances of the ground rod of 50 m long are considerably dependent on the frequency. The ground impedance is mainly resistive in the frequency range of 3-20 kHz. At higher frequencies, the reactive components of the ground impedances are no longer negligible and the inductance of the ground rod was found to be the core factor deciding the ground impedance. Although the steady-state ground resistance of the ground rod of 50 m was less than that of the ground rod of 10 m, the ground impedances of the ground rod of 50 m over the frequency range of more than 60 kHz were much greater than those of the ground rod of 10 m. Furthermore, the equivalent circuit model based on the measured data was proposed. and the calculated results were in approximately agreement with the measured data.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.820-825
• /
• 2004

In this paper an octave tuning voltage controlled oscillator which is used in set-top TV tuner was designed. Oscillation frequency range is 0.9 GHz～2.2 GHz with 1.3 GHz bandwidth. By using 4 varactor diodes in base and emitter of transistor, wide-band tuning, sweep linearity and low phase noise could be achieved. Designed VCO requires a tuning voltage of 0 V ～ 20 V and DC consumption of 10 V and 15 mA. Designed VCO exhibits an output power of 5.3 dBm $\pm$1.1 dB and a phase noise below -94.8 dBc/Hz ＠ 10 kHz over the entire frequency range. The sweep linearity shows 65 MHz/V with a deviation of $\pm$10 MHz.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.406-409
• /
• 1997

In this paper, the power spectral analysis and fractral dimension analysis of heart rate variability(HRV) were performed to evaluate effects of orthostatic stress with head-up tilt on autonomic nervous system(ANS) for 24 young and healthy subjects(age: $24{\pm}5yr$.). The ECG and respiration signals were recorded at the tilt angle of $0^{\circ},\;15^{\circ},\;30^{\circ},\;45^{\circ},\;70^{\circ}$ and $90^{\circ}$ successively for 5 minutes per each stage under the condition of frequency controlled respiration (0.25Hz). Heart rate(HR) gradually increased as the angle increased. Similarly, according to the increment of angle, normalized low frequency(LF) component(0.05-0.15Hz) gradually increased, whereas normalized high frequency(HF) component (0.20-0.30Hz) was reduced. From these results it is speculated that orthostatic stress, head-up tilt, results in the prevalence of sympathetic tone in autonomic balance with the increment of sympathetic tone and the decrement of parasympathetic tone, which seems to mean that autonomic nervous system plays a major role in compensating for disturbances of cardiovascular system due to it.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.181-182
• /
• 2011

수중에서는 대기와는 달리 매질의 차이로 인하여 통신의 제약이 따르므로 초음파를 이용하여 정보를 송 수신한다. 수중통신을 하기 위해서는 신호를 증폭시키는 전력증폭기와 초음파를 발생시키는 트랜스듀서가 필요하다. 전력증폭기는 수중에서의 발열과 연료문제로 인하여 높은 효율로 동작하여야한다. 하지만 전력증폭기에 인가되는 고정전압과 출력전압의 차이로 인해 손실이 발생하여 효율이 저하된다. 그러므로 본 논문에서는 전력증폭기의 효율 향상을 위해 출력전압에 따라 인가전압을 가변하는 ET(Envelope Tracking) 기술을 적용하기 위한 4[kW]급, 20[kHz]의 대역폭을 갖는 가변 DC-DC 컨버터를 설계하고 시뮬레이션을 통해 특성을 확인하였다.