• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.839-846
• /
• 2007

In this paper, the first attempt to design a novel structure of dual-band feedforward linear power amplifier(FFW LPA) was presented. Up to now, primary technical difficulty has been the extension of the conventional signal canceller to the dual-band operation. Therefore, we propose the design technique of the dual-band equal group delayed carrier canceller, the dual-band equal group delayed intermodulation distortion(IMD) canceller and the dual-band FFW LPA. The operation frequency bands of the implemented dual-band FFW LPA are digital cellular($f_0=880$ MHz) and IMT-2000($f_0=2.14$ GHz) band, which are separated about 1.26 GHz. With the high power amplifier of 120 W PEP for commercial base-station application, IMD cancellation loop shows 20.45 dB and 25.04 dB loop suppression at each band of operation for 100 MHz. From the adjacent channel leakage ratio(ACLR) measurement with CDMA IS-95A 4FA and WCDMA 4FA signal, we obtained 16.52 dB improvement at the average output power of 41.5 dBm for digital cellular band, and 18.59 dB improvement at the average output power of 40 dBm for IMT-2000 band simultaneously.

• Progress in Medical Physics
• /
• v.5 no.2
• /
• pp.35-43
• /
• 1994

Electromagnetic wave may induce effect and damage on the bio-body, either by electric fields of magnetic fields. We measure electrophysiological changs in rabbit's brain exposed to 2.45GHz micro wave(power density 40mW/cm$^2$) which distance 30cm from the source. In order to process the bio-electrical signal (EEG), used pre-amplifier module with self-made and Digtal analyzer computer system. Spectal analysis of the EEG showed variable power in the frequency range(1～30Hz) through each exposure time(10min, 20min, 30min) before and after. In effectively measured by the bio-electrical signal processing and can found threshold of minmal permissible exposure and lethal exposure.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.4
• /
• pp.32-42
• /
• 2010

In this paper, we represent considering parameters for design of a Cartesian vector modulator predistorter to maximize linearity improvement of the predistorter and propose an advanced Cartesian vector modulator predistrotrer with nonlinear starting point control circuit. In order to confirm the performance of the proposed predistorter, the predistorter is applied to power amplifier with 15 W output power for 2.5 GHz band mobile WiMax 1-FA signal. From the measured results, ACLR of -45.3 dBc with 4 dB improvement of ALCR compared with the previous predistorter is obtained and linearity improvement range is also extended.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.9
• /
• pp.55-59
• /
• 2008

In this paper, the linearity of Doherty amplifier has been improved by applying a compact slow-wave microstrip branch-line coupler on the output of Doherty amplifier. The proposed branch coupler has four microstrip high-low impedance resonant cells periodically placed inside the branch-line coupler to result in high slow-wave effect. The new coupler not only effectively reduces the occupied area to 30% of the conventional branch-line coupler at 1.8GHz, but also has high second harmonic suppression performance. We obtained the 3rd-order intermodulation distortion ($IMD_3$) of -31.16 dBc for CDMA applications with that of maintaining the constant power added efficiency (PAE). The IMD3 performance is improved as much as -7 dBc compared with a Doherty amplifier.

• 전자공학회논문지 IE
• /
• v.45 no.1
• /
• pp.31-37
• /
• 2008

A Wibro RF down converter of 2.3GHz band is designed and implemented in this paper. The problems that can occur in the receiver LNA(Low Noise Amplifier) to minimize additional purposes. In addition, 2.3GHz band from the 75 MHz downward to minimize the losses in the process, transform and improve efficiency, and achieve stable characteristics can be used to make high frequency characteristics of the device. Wibro repeater uses a TDMA(Time Division Multiplexing Access) method is needed because the RF switch. Production criterion specification, the input voltage from +8 V 1.2A of current consumption, 60dB gain and the noise figure of less than 2.5dB, VSWR(Voltage Standing Wave Ratio) less than 1.5, more than IMD(Inter Modulation Distortion) 60dB satisfied. Environmental conditions ($-20^{\circ}C$ to $70^{\circ}C$) to pass the test of reliability in a long time, that seemed crafted Wibro down converter be applied to the Wibro repeater.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.917-924
• /
• 2019

This paper presents a wideband low noise amplifier (LNA) that is suitable for LTE-Advanced and 5G communication standards employing carrier aggregation (CA). The proposed LNA encompasses a common input stage and a dual output second stage with a buffer at each distinct output. This architecture is targeted to operate in both intra-band (contiguous and non-contiguous) and inter-band CA. In the proposed design, the input and second stages employ a gm enhancement with resistive feedback technique to achieve self-biasing, enhanced gain, wide bandwidth as well as reduced noise figure of the proposed LNA. An up/down power controller controls the single input single out (SISO) and single input multiple outputs (SIMO) modes of operation for inter-band and intra-band operations. The proposed LNA is designed with a 45nm CMOS technology. For SISO mode of operation, the LNA operates from 0.52GHz to 4.29GHz with a maximum power gain of 17.77dB, 2.88dB minimum noise figure and input (output) matching performance better than -10dB. For SIMO mode of operation, the proposed LNA operates from 0.52GHz to 4.44GHz with a maximum voltage gain of 18.30dB, a minimum noise figure of 2.82dB with equally good matching performance. An $IIP_3$ value of -6.7dBm is achieved in both SISO and SIMO operations. with a maximum current of 42mA consumed (LNA+buffer in SIMO operation) from a 1.2V supply.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.2
• /
• pp.32-43
• /
• 2004

RFID 시스템에서 태그는 리더와 전자기 에너지 교환에 의해 동작을 하며 배터리를 사용하는 active 형 태그와 배터리를 사용하지 않는 passive형 태그로 크게 구분된다. 또한 태그는 자체 회로구조에 의해 harmonic 태그, anharmonic 태그, sequenced amplifier 태그로 나뉜다. Passive 태그에서는 리더의 반송파 backscatter 방식을 이용하여 동작을 하며 active 태그는 자체 발진회로에 의해 태그정보를 송신한다. 태그의 변조방식으로 PSK, FSK, ASK 등을 사용하며 변조방법에 따라 회로 구성과 프로토콜 설계가 달라진다. 또한 리더의 전파 신호를 정류하기 위하여 렉테나(rectenna)가 필요하다. 본 논문에서는 태그의 분류, 동작, 구조 등에 관한 일반적인 내용을 기술하였다. 특히 UHF 대역 이상의 태그 기술 최근 추세가 안테나 부분을 제외하고 CMOS one chip화 하는 수준으로서 900 MHz UHF 대역, 2.45 GHz RFID 칩이 상용화 되어 있다. 칩의 내부구조와 태그의 변조방식에 의거한 동작에 관한 개괄적인 내용을 서술하였다.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1601-1602
• /
• 2006

A cascode low noise amplifier(LNA) for a 2.45GHz RFID reader is designed using 0.25um CMOS technology. There are four LNA design techniques applied to the cascode topology. In this paper, power-constrained simultaneous noise and input matching(PCSNIM) technique is used for low power consumption and achieving the noise matching and input matching simultaneously. Simulation results demonstrate a noise figure of 2.75dB, a power gain of 10.17dB, and a dissipation power of 8.65mW with 1V supply.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.42 no.8 s.338
• /
• pp.53-60
• /
• 2005

Recently, sub-micron CMOS technologies have taken the place of III-V materials in a number of areas in integrated circuit designs, in particular even for the applications of gjgabit optical communication applications due to its low cost, high integration level, low power dissipation, and short turn-around time characteristics. In this paper, a four-channel transimpedance amplifier (TIA) array is realized in a standard 0.35mm CMOS technology Each channel includes an optical PIN photodiode and a TIA incorporating the fully differential regulated cascode (RGC) input configuration to achieve effectively enhanced transconductance(gm) and also exploiting the inductive peaking technique to extend the bandwidth. Post-layout simulations show that each TIA demonstrates the mid-band transimpedance gain of 59.3dBW, the -3dB bandwidth of 2.45GHz for 0.5pF photodiode capacitance, and the average noise current spectral density of 18.4pA/sqrt(Hz). The TIA array dissipates 92mw p in total from a single 3.3V supply The four-channel RGC TIA array is suitable for low-power, high-speed optical interconnect applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.358-365
• /
• 2008

A differential-gain-controlled LNA is designed and implemented in 0.18 um CMOS technology for $3.1{\sim}4.8GHz$ UWB system. In high gain mode, measurements show a differential power gain of $14.1{\sim}15.8dB,\;13.3{\sim}15dB$, respectably, an input return loss higher then 10dB, an input IP3 of -19.3 dBm, a noise figure of $4.85{\sim}5.09dB$, while consuming only 19.8 mW of power from a 1.8V DC supply. In low gain mode, measurements show a differential power gain of $-6.1{\sim}-4.2dB,\;-7.6{\sim}-5.6dB$, respectably, an input return loss higher then 10dB, an input IP3 of -1.45 dBm, a noise figure of $8.8{\sim}10.3dB$, while consuming only 5.4mW of power from a 1.8V DC supply.