• Journal of ILASS-Korea
• /
• 제19권2호
• /
• pp.64-68
• /
• 2014

A driving vehicle performance which is driven by FTP-75 mode was simulated by computer. Throttle valve position, engine speed, air mass flow rate, fuel consumption et al. were computer simulated. A set of engine part load performance data, automatic transmission shift map and vehicle specifications were used for the computer simulation. Throttle valve position, engine speed, air mass flow rate et al. measured for evaluating the computer simulation results by driving the vehicle with FTP-75 mode on a chassis dynamometer. GT-Power$^{(R)}$ software was used for the computer simulation of the driving vehicle performance. Experimental fuel consumption rate was measured by using an ECU HILS fuel injection system. The experimental data and simulation results were compared. The computer simulation of the driving vehicle performance predicts the measured data well comparatively.

• Journal of Biosystems Engineering
• /
• 제9권2호
• /
• pp.1-7
• /
• 1984

The engines mounted on power-tillers are used as power source in various kinds of works such as plowing, harrowing, transporting, spraying, water pumping and threshing, etc. But the engines have not been used effectively from a standpoint of fuel consumption because of lack of proper power transmission system and lack of understanding of fuel consumption characteristics of the engines. Therefore, this study was attempted to establish proper power transmission system between the power-tiller engines and various implements. In order to accomplish the above objective, firstly, power requirement and pulley sizes for various implements, which are driven by the power-tiller engines, were investigated to find out whether the power transmission system is proper. Secondly, partload variable engine-speed test was conducted for 3 different sizes of diesel engines to measure to specific fuel consumption. Thirdly, the present power transmission systems were analyzed in terms of specific fuel consumption, and proper power transmission systems were suggested for various implements. The results of this study are summarized as follows: 1. Power requirement for each fixed-type implement of power-tiller varied from 1.5 ps to 11 ps according to its type and operating conditions, but generally in the range of 2.5 ps to 7 ps. 2. Each power tiller and implement were equipped with only one size of pully with few exeptions. With the present power transmission systems, the engines can't be utilized effectively in terms of fuel economy. The pulley size of engine or implement should be diversified to provide the optimum engine speed for different implements. 3. For a diesel eninge with the rated power output of 6 ps, the optimum engine speed to minimize specific fuel consumption was 2200 rpm for the power reguirement in the range of 6 ps or more, 1700 rpm in the range of 4 to 6 ps, and 1200 rpm in the range of 4 ps or less. 4. For a diesel engine with the rated power output of 8 ps, the optimum engine speed was 2200 rpm for the power requirement in the range of 7 ps or more, 1700 rpm in the range of 4.8 to 7 ps, and 1200 rpm in the range of 4.8 ps or less. 5. For a diesel engine with the rated power output of 10 ps, the optimum engine speed was 2200 rpm for the power requirement in the range of 8.4 ps or more, 1700 rpm in the range of 5.4 ps to 8.4 ps, and 1200 rpm in thr range of 5.4 ps or less. 6. Provided the existing implements are dirven by 8 ps diesel engines, the optimum size of engine pulley should be larger than 120mm for the works of requiring less than 4 ps and 90-110mm for the works requiring 4.5-6.5 ps in order to minimize fuel consumption.

• The Journal of the Korea institute of electronic communication sciences
• /
• 제12권5호
• /
• pp.771-776
• /
• 2017

LTE-R mobile communication technology based on LTE is used to supply various signal and exchange information required for safety operation of train on high speed railway communication system. In this paper, transmission performance of application traffic which is transferred on high speed communication based on LTE-R is analyzed. And some suggestions for application traffic transmission of high speed railway communication will be considered. Computer simulation is used to analyze performance of CBR, VBR as application traffic. Throughput, delay and packet loss rate is used as performance measurement and analysis parameters.

• The Journal of the Acoustical Society of Korea
• /
• 제21권2호
• /
• pp.110-119
• /
• 2002

Acoustic characteristics of water sediment were experimentally studied in laboratory. Water saturated sand sediment less than the grain size of 0.5 mm diameter is uniformly distributed in an acryl box (100 mm×100mm×42mm) with material thickness 1 mm. Pores in the acryl box are modeled as the structure of cylindrical pore tubes (diameter 3 mm and length 42 mm) filled with water. Cylindrical pore tubes have porosities 0%, 5%, 11%, 18% and 26 % controlled by the tube numbers. Transmitted acoustic waves through sand sediment specimen are analyzed as the functions of porosity and frequency from 0.3 MHz to 4 MHz. Transmitted acoustic waves are mixed with the first-kind wave from whole specimen and the second-kind wane from cylindrical pore tubes. For the center frequency 1 MHz, the first kind wave is dominant but for the center frequency 2.25 MHz, the second kind wave is dominant. In the case of the first-kind wave, as the porosity increases, the transmission coefficient decreases and the sound speed decreases to the sound speed of water. As the frequency increases, the transmission coefficient decreases but the sound speed is almost constant. In the case of the second-kind wave, as the porosity increases, the transmission coefficient increases but the sound speed is almost constant. The transmission coefficient and the sound speed are almost constant as a function of frequency.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 한국정보통신학회 2013년도 추계학술대회
• /
• pp.386-389
• /
• 2013

In this paper, for signal integrity analysing high-speed signal between a processor and a DDR2 memory, transient analysis is done and eye diagrams are generated using IBIS models of IC chips and S-parameters of transmission line. From the eye diagrams of such high-speed signals as DQ, DQS/DQSb, Clock, Address and Control, signal quality is assured through measuring timing and voltage margins during setup and hold times and verifying that the over-/under-shoot and the cross points of differential signals satisfy their specifications.

• Magazine of the Korean Society of Agricultural Engineers
• /
• 제15권3호
• /
• pp.3089-3095
• /
• 1973

The power transmission to the traction devices may be very important for the tractor performance and therefore this system has been studied very much in the past. On the other hand, the PTO(Power-take-off) has been considered as an accessary on the tractor with a few work for its power transmission. Because of increased use of PTO operation in various kind of farming operations in recent years, the function of PTO may become such important as the traction facilities. In this study, the power transmission characteristics of PTO drive was analyzed theoretically and some experimental work was done to study on it. The results of the study are as follows: 1) The most stable condition of PTO work was obtained when the intersection angle of the two curves for driving and driven torques was about ${\pi}/2$. 2) To obtain the most stable operation it is better to use both the speed control and the full control together. 3) Six steps differential gear may not be enough to use the PTO power smoothly. It is thought that the three steps differential gear on the shaft of PTO may be necessary additionally for a smooth operation. 4) When the traction facilities and the PTO are used at the same time, the torque of crank shaft becomes Tt + Tp, and the high efficiency and good stability of word will be obtained with the small variation of driving speed. 5) When the tractor was operated with 75% of the rated horse power and 70% of maximum speed, the best thermal efficiency could be obtained. 6) The most dangerous sound for human occured at the rated speed of PTO and tus it may be necessary to control the dangerous noise.

• Journal of Digital Contents Society
• /
• 제18권6호
• /
• pp.1193-1198
• /
• 2017

The IGBT structure developed in this paper is used as a high power switch semiconductor for DC transmission and distribution and it is expected that it will be used as an important electronic device for new and long distance DC transmission in the future by securing fast switching speed and improved breakdown voltage characteristic. As a new type of next generation power semiconductors, it is designed to improve the switching speed while at the same time improving the breakdown voltage characteristics, reducing power loss characteristics, and achieving high current density advantages at the same time. These improved properties were obtained by further introducing SiO2 into the N-drift region of the Planar IGBT and were compared and analyzed using the Sentaurus TCAD simulation tool.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제26권12호
• /
• pp.2615-2623
• /
• 2002

In this paper, a systematic design approach for a three shaft hydromechanical transmission(HMT) system is proposed by considering the power characteristics and speed ratio range. Using network analysis, possible configurations of the 3 shaft HMT are analyzed and it is found that the influence of HSU stroke on the power distribution of the HMT can be investigated by the network analysis. In addition, design methods are presented from the viewpoint of (1) power distribution and (2) speed ratio range. From the power distribution and the speed ratio range, a HMT configuration can be constructed, which minimizes the power circulation and provides the desired speed ranges. Based on the 3 shaft HMT analyses and the proposed design approach, a 3 shaft HMT is designed which provides 4 speeds in forward and 1 speed in reverse while keeping the power circulation less than 150% of the input power. It is expected that the design method suggested in this study can be used in a systematic design of the 3 shaft HMT.

• Journal of Biosystems Engineering
• /
• 제36권4호
• /
• pp.243-251
• /
• 2011

Purpose of this study was to analyze power requirement of an agricultural tractor for baler operation. First, a power measurement system was developed and installed in a 75 kW agricultural tractor. Strain-gages with a telemetry system were used to measure torques of transmission and PTO input shafts. An engine tachometer was used to measure rotational speed of transmission and PTO input shafts. The measurement system also included pressure sensors to measure pressure of hydraulic pumps, an I/O interface to acquire the sensor signals, and an embedded system to determine power requirements. Second, field experiments were conducted at two PTO speed levels, and proportion of utilization ratio of rated engine power and power consumption of major parts (transmission input shaft, PTO input shaft, main hydraulic pump, and auxiliary hydraulic pump) were analyzed. Results of usage proportion of engine power for PTO speed level 1 and 2 were 4.1 and 2.2%, 31.5 and 16.3%, 49.6 and 59.7%, 14.4 and 20.8%, and 0.4 and 1.0%, respectively, for ratio of measured engine power to rated engine power of less than 25%, 25 ~ 50%, 50 ~ 75%, 75 ~ 100%, and greater than 100%. The results showed that the usage proportion increased in the range with the ratio of power requirement to rated engine power of over than 50% when the PTO gear was shifted from P1 to P2. Averaged engine power requirement for baling operation, tying and discharging operation, and total operation were 43.3, 37.3, and 42.0 kW and 49.0, 37.0, and 47.4 kW, respectively, for PTO speed level 1 and 2. Paired t-test showed significant difference in power consumption of engine, transmission input shaft, and PTO input shaft for different PTO speed levels. Therefore, the power consumption of engine for baler operation increased when the PTO gear was shifted from P1 to P2. It was indicated that the power requirement of tractor was affected by the PTO rotational speed for baler operation.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• 제15권2호
• /
• pp.66-71
• /
• 2016

For the manual transmission gearbox used in the automotive industry, gear meshing transmission error is the main source of noise known as gear whine, and radiated gear whine noise plays an important role in the whole gearbox. Therefore, in order to keep competitive in the automotive market, the NVH performance of transmission gearboxes is increasingly important for automotive manufacturers when a new product is developed. In this paper, in order to achieve an optimized tooth contact pattern, gear tooth modification is applied to make up for the deformation of the teeth owing to load. A five-speed MT gearbox is firstly modeled in RomaxDesign software and the prediction of transmission error under the loaded torques is studied and compared. From the simulation, the transmission error and maximum contact stress are also simulated and compared after tooth modification of the loaded torques. Finally, the simulation results are used to optimize the whole gearbox design and the final gearbox prototype is testified to obtain NVH performance in a semi-anechoic room.