• Journal of the Korean Institute of Telematics and Electronics
• /
• v.19 no.3
• /
• pp.13-18
• /
• 1982

This Paper is an experimental study on the effective dielectric constant of microstrip line. To quantify the dispersive effects on a microstrip line, the effective dielectric constant, which is the ratio of free space wavelength to guide wavelength, is calculated for teflon substrates. The calculation is based on the Fourier transform of the current distribution on microstrip line. Measurements of effective dielectric constant using a microstrip elliptic resonator and ring resonator are also described. As a result, the computed values of effective dielectric constant agree almost all with measured values, using ring and elliptic resonator, in case of w/h or the ratio of microstrip width to substrate thickness equal unity over frequency range of 8 to 12GHz.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.4
• /
• pp.1458-1470
• /
• 2018

In this letter, a new dual-port Multiple-Input Multiple-Output (MIMO) antenna is introduced which has two independent signal feeding ports in a single antenna element to achieve smaller antenna volumes for the 5G mobile applications. The dual-port structure is implemented by adding a cross coupled semi-loop (CCSL) antenna as the secondary radiator to the ground short of inverted-F antenna (IFA). It is found that the port to port isolation is not deteriorated when an IFA and CCSL is combined to form a dual-port structure. The isolation property of the proposed antenna is compared with a polarization diversity based dual-port antenna proposed in the literature [9]. The operating frequency range is 3.3-4.0 GHz which is suitable for places where $4{\times}4$ MIMO systems are supposed to be deployed such as in China, EU, Korea and Japan at the band ${\times}$ (3.3 - 3.8GHz. The measured 6-dB impedance bandwidths of the proposed antennas are larger than 700 MHz with isolation between the feeding ports higher than 18 dB [1-2]. The simulation and measurement results show that the proposed antenna concept is a very promising alternative for 5G mobile applications.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.9 no.4
• /
• pp.141-146
• /
• 2010

In this paper, bandgap reference PTAT(Proportional to Absolute Temperature) circuit and flexible gain control of LNA(Low Noise Amplifier) which is usable in Zigbee system of 2.4GHz band are designed by TSMC $0.18{\mu}m$ CMOS library. PTAT bandgap reference circuit is proposed to minimize the instability of CMOS circuit which may be unstable in temperature changes. This circuit is designed such that output voltage remains within 1.3V even when the temperature varies from $-40^{\circ}C$ to $-50^{\circ}C$ when applied to the gate bias voltage of LNA. In addition, the LNA is designed to be operated on 2.4GHz which is applicable to Zigbee system and able to select gains by changing output impedance using 4 NMOS operated switches. The simulation result shows that achieved gain is 14.3~17.6dB and NF (Noise Figure) 1.008~1.032dB.

• ETRI Journal
• /
• v.36 no.1
• /
• pp.116-123
• /
• 2014

In this paper, a novel unequal broadband out-of-phase power divider (PD) is presented. Double-sided parallel-strip lines (DSPSLs) are employed to achieve an out-of-phase response. Also, an asymmetric dual-band matching structure with two external isolation resistors is utilized to obtain arbitrary unequal power division, in which the resistors are directly grounded for heat sinking. A through ground via (TGV), connecting the top and bottom sides of the DSPSLs, is used to short the isolation components. Additionally, this property can efficiently improve the broadband matching and isolation bandwidths. To investigate the proposed divider in detail, a set of design equations are derived based on the circuit theory and transmission line theory. The theoretical analysis shows that broadband responses can be obtained as proper frequency ratios are adopted. To verify the proposed concept, a sample divider with a power division of 2:1 is demonstrated. The measured results exhibit a broad bandwidth from 1.19 GHz to 2.19 GHz (59.2%) with a return loss better than 10 dB and port isolation of 18 dB.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.874-877
• /
• 2018

Many SMDs (surface mount device) are mounted and mutually connected on a PCB (printed circuit board). System performance degrades when their transmission characteristics are bad. Pads connecting a PCB and SMDs affects PCB transmission characteristics significantly, so pad should be properly aligned to optimize impedance matching. In this paper, effects on PCB transmission characteristics are simulated by pad alignment. When frequency is relatively low, pad alignment seldom affect PCB transmission characteristics, but it affects more and more when frequency or pad size becomes larger. Therefore, pad alignment should be carefully chosen based on target frequency and pad size. Especially, the proposed edge-aligned pad is generally more advantageous over the conventional centered-aligned pad in 12~16 GHz Ku-band frequency.

• Journal of Multimedia Information System
• /
• v.5 no.2
• /
• pp.91-98
• /
• 2018

We devised a bird-borne transceiver unit for S-band packet radio communications based on the CC2500 transceiver, a device manufactured by Texas Instruments (TI). Our assessments determined the optimal parameters needed to achieve successful bird-to-center communication over a distance of 18 km and bird-to-bird communication over a distance of 200 m. These parameters included optimal modulation methods, transmission rates, and antennas. We equipped the transceiver unit with a modified dipole antenna (collinear antenna), which we tested in a 10 m anechoic chamber. Our experimental assessments and circuit design review identified the following parameters: 2FSK modulation method; 14.28 kHz frequency shift; 101.56 kHz IF reception bandwidth; and Manchester encoding (+). Our assessments showed bird-to-bird communications could be achieved over a distance of 200 m assuming MSK, FEC (+), and 500 kbps. Following tests by an official body, we obtained 28 sets of a type approval license for 2.4 GHz. In cooperation with the Yamashina Institute for Ornithology, we attempted to tag and release six or more swans. This unit gives us the ability to obtain vital data on swans. We expect this data to provide significant benefits, including clues on improving screening for infected individuals.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.206-212
• /
• 2007

In this paper, a novel power/ground plane using the hybrid-cell electromagnetic band-gap(EBG) structure is proposed for the wide-band suppression of the ground bound noise(GBN) or simultaneous switching noise(SSN). The -30 dB stopband of the proposed structure starts from a few hundred MHz where the GBN/SSN energy is dominant. The distinctive features of this new structure are the thin spiral strip line and hybrid-cells. They realize the enhanced inductance and the shorter period of the EBG lattice. As a result, the lower cut-off frequency and bandwidth of the -30 dB stopband becomes lower and wider, respectively. In addition, the proposed structure has smaller number of resonance modes between power/ground planes and performs a low EMI behavior compared with the reference board.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.358-365
• /
• 2008

A differential-gain-controlled LNA is designed and implemented in 0.18 um CMOS technology for $3.1{\sim}4.8GHz$ UWB system. In high gain mode, measurements show a differential power gain of $14.1{\sim}15.8dB,\;13.3{\sim}15dB$, respectably, an input return loss higher then 10dB, an input IP3 of -19.3 dBm, a noise figure of $4.85{\sim}5.09dB$, while consuming only 19.8 mW of power from a 1.8V DC supply. In low gain mode, measurements show a differential power gain of $-6.1{\sim}-4.2dB,\;-7.6{\sim}-5.6dB$, respectably, an input return loss higher then 10dB, an input IP3 of -1.45 dBm, a noise figure of $8.8{\sim}10.3dB$, while consuming only 5.4mW of power from a 1.8V DC supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.90-95
• /
• 2007

Chaotic OOK(On-Off Keying) modulation method can be used in LDR(Low Data Rate) UWB systems. The chaotic generator in one of the most important circuit in this system. The traditional chaotic generator circuits using analog feed back technique have low yield characteristic due to the process variation. A novel quasi-chaotic signal generator using digital PN-sequence in proposed in this paper and verified in 0.18um CMOS teleology.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.10
• /
• pp.1142-1149
• /
• 2007

In this paper, the development of wideband MIMO channel sounder and a pilot measurement result is described for research on the multi antenna radio propagation characteristics considering urban environment at microwave frequencies. We developed $4{\times}4$ MIMO(BW:100 MHz) channel sounder using the high speed switching mechanism and periodic pseudo random binary signals method considering next generation mobile communication system. A pilot measurement campaign at the urban area of Bundang is presented for confirmation of system performance. From the analysis of measurement data, wideband path loss exponent of 3.7 and 8 GHz band is 1.79 and 1.76. Average RMS delay spread is 200 ns and 42 ns respectively. From the experiment results, operation of this measurement system is confirmed considering research for a coverage, SNR and channel capacity in urban environment at microwave frequencies.