• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.13 no.1
• /
• pp.1-7
• /
• 2020

Directivity control technology of sound system is a key technology for improving sound quality. Providing a line source rather than a point source in an acoustic system can reduce the effects of attenuation interference at long distances, thereby providing high quality sound. In particular, A line-array speaker system can be used to provide coherent, high-quality sound over long distances. However, high frequencies have shorter wavelengths, so the distance between the speakers of a line array system must be shorter, but there are physical limitations. In this paper, we designed a wave guide and installed it in the speaker's compression driver to solve this problem. We measured and tested various acoustic characteristics to verify the performance of the speaker. As a result, when the line array sound system is constructed using the developed speakers, it is possible to provide a line source in all areas including the treble range, thereby achieving the same effect as a single extended source and providing high quality sound up to far distances.

• The Journal of Korean Academy of Prosthodontics
• /
• v.50 no.1
• /
• pp.36-43
• /
• 2012

Purpose: To analyze the stress distribution of the implant and its supporting structures through 3D finite elements analysis for implants with different hexagon heights and to make the assessment of the mechanical stability and the effect of the elements. Materials and methods: Infinite elements modeling with CAD data was designed. The modeling was done as follows; an external connection type ${\phi}4.0mm{\times}11.5mm$ Osstem$^{(R)}$ USII (Osstem Co., Pusan, Korea) implant system was used, the implant was planted in the mandibular first molar region with appropriate prosthetic restoration, the hexagon (implant fixture's external connection) height of 0.0, 0.7, 1.2, and 1.5 mm were applied. ABAQUS 6.4 (ABAQUS, Inc., Providence, USA) was used to calculate the stress value. The force distribution via color distribution on each experimental group's implant fixture and titanium screw was studied based on the equivalent stress (von Mises stress). The maximum stress level of each element (crown, implant screw, implant fixture, cortical bone and cancellous bone) was compared. Results: The hexagonal height of the implant with external connection had an influence on the stress distribution of the fixture, screw and upper prosthesis and the surrounding supporting bone. As the hexagon height increased, the stress was well distributed and there was a decrease in the maximum stress value. If the height of the hexagon reached over 1.2mm, there was no significant influence on the stress distribution. Conclusion: For implants with external connections, a hexagon is vital for stress distribution. As the height of the hexagon increased, the more effective stress distribution was observed.

• Archives of design research
• /
• v.13 no.1
• /
• pp.209-218
• /
• 2000

The purpose of this study was to improve the curriculum for industrial design department in the junior colleges. In order to achieve the purpose, two methodologies were carried out. First is job analysis of the industrial designers who have worked in the small & medium manufacturing companies, second is survey for the opinions of professors in the junior colleges. Some results were as follows: 1. The period of junior college for industrial designers is 2 years according to present. But selectively 1 year of advanced course can be established. 2. The practice subjects same as computational formative techniques needed to product development have to be increased. In addition kinds of selection subjects same as foreign language, manufacturing process, new product information and consumer behavior investigation have to be extended. 3. The next subjects need to adjust the title, contents and hours. (1) The need of 3.D related subjects same as computer modeling, computer rendering, 3.D modeling was high. The use of computer is required to design presentation subjects. (2)The need of advertising and sale related subjects same as printing, merchandise, package, typography, photography was low, the need of presentation techniques of new product development was high. (3) The need of field practice, special lecture on practice and reading original texts related subjects was same as at present, but these are not attached importance to form. As the designers feel keenly the necessity of using foreign language, the need of language subject was high.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.121-127
• /
• 2018

A system for diagnosing surface defects of long and large pipe inner overlay welds, 1m in diameter and 6m in length, was developed using a Liquid Penetrant Test (PT). First, CATIA was used to model all major units and PT machines in 3-dimensions. They were used for structural strength analysis and strain analysis, and to check the motion interference phenomenon of each unit to produce two-dimensional production drawings. Structural strength analysis and deformation analysis using the ANSYS results in a maximum equivalent stress of 44.901 MPa, which is less than the yield tensile strength of SS400 (200 MPa), a material of the PT Machine. An examination of the performance of the developed equipment revealed a maximum travel speed of 7.2 m/min., maximum rotational speed of 9 rpm, repeatable position accuracy of 1.2 mm, and inspection speed of $1.65m^2/min$. The results of the automatic PT-inspection system developed to check for surface defects, such as cracks, porosity, and undercut, were in accordance with the method of ASME SEC. V&VIII. In addition, the results of corrosion testing of the overlay weld layer in accordance with the ferric chloride fitting test by the method of ASME G48-11 indicated that the weight loss was $0.3g/m^2$, and met the specifications. Furthermore, the chemical composition of the overlay welds was analyzed according to the method described in ASTM A375-14, and all components met the specifications.

• The Journal of Korean Society for Radiation Therapy
• /
• v.14 no.1
• /
• pp.175-186
• /
• 2002

The purpose of this study is directly measure and evaluate about absorbed dose change according to nominal energy and electron cone or medical accelerator on isodose curve, percentage depth dose, contaminated X-ray, inhomogeneous tissue, oblique surface and irradiation on intracavitary that electron beam with high energy distributed in tissue, and it settled standard data of hish energy electron beam treatment, and offer to exactly data for new dote distribution modeling study based on experimental resuls and theory. Electron beam with hish energy of $6{\sim}20$ MeV is used that generated from medical linear accelerator (Clinac 2100C/D, Varian) for the experiment, andwater phantom and Farmer chamber md Markus chamber und for absorbe d dose measurement of electron beam, and standard absorbed dose is calculated by standard measurements of International Atomic Energy Agency(IAEA) TRS 277. Dose analyzer (700i dose distribution analyzer, Wellhofer), film (X-OmatV, Kodak), external cone, intracavitary cone, cork, animal compact bone and air were used for don distribution measurement. As the results of absorbed dose ratio increased while irradiation field was increased, it appeared maximum at some irradiation field size and decreased though irradiation field size was more increased, and it decreased greatly while energy of electron beam was increased, and scattered dose on wall of electron cone was the cause. In percentage depth dose curve of electron beam, Effective depth dose(R80) for nominal energy of 6, 9, 12, 16 and 20 MeV are 1.85, 2.93, 4.07, 5.37 and 6.53 cm respectively, which seems to be one third of electron beam energy (MeV). Contaminated X-ray was generated from interaction between electron beam with high energy and material, and it was about $0.3{\sim}2.3\%$ of maximum dose and increased with increasing energy. Change of depth dose ratio of electron beam was compared with theory by Monte Carlo simulation, and calculation and measured value by Pencil beam model reciprocally, and percentage depth dose and measured value by Pencil beam were agreed almost, however, there were a little lack on build up area and error increased in pendulum and multi treatment since there was no contaminated X-ray part. Percentage depth dose calculated by Monte Carlo simulation appeared to be less from all part except maximum dose area from the curve. The change of percentage depth dose by inhomogeneous tissue, maximum range after penetration the 1 cm bone was moved 1 cm toward to surface then polystyrene phantom. In case of 1 cm and 2 cm cork, it was moved 0.5 cm and 1 cm toward to depth, respectively. In case of air, practical range was extended toward depth without energy loss. Irradiation on intracavitary is using straight and beveled type cones of 2.5, 3.0, 3.5 $cm{\phi}$, and maximum and effective $80\%$ dose depth increases while electron beam energy and size of electron cone increase. In case of contaminated X-ray, as the energy increase, straight type cones were more highly appeared then beveled type. The output factor of intracavitary small field electron cone was $15{\sim}86\%$ of standard external electron cone($15{\times}15cm^2$) and straight type was slightly higher then beveled type.

• Progress in Medical Physics
• /
• v.16 no.3
• /
• pp.125-129
• /
• 2005

The first step in the commissioning procedure of a treatment planning system is always verification of the basic beam data. In this work, we have measured POD curves and beam profiles between 1 $\times$ 1 cm$^{2}$ and 40 $\times$ 40 cm$^{2}$ . In an attempt, Pinnacle 7.4f detect discrepancies between predicted dose distribution and delivered dose distribution. The discrepancies between measurement data and caculation data was found. The delivered dose was underestimated in field but overestimated out of field. The D$_{max}$ depth of 1 $\times$ 1 cm$^{2}$ was reduced about 2 mm. For the larger field size ($\geq$4$\times$4 cm$^{2}$, the beam profile and PDD curve showed good agreement between measurement data and calculation data.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.12 no.3
• /
• pp.183-196
• /
• 2010

Increasing human activity due to rapid economic growth and land use change alters the patterns of the Asian monsoon, which is key to crop yields in Asia. In this study, we tested the performance of regional climate model (RegCM3) by simulating important components of Indian summer monsoon, including land-ocean contrast, low level jet (LLJ), Tibetan high and upper level Easterly Jet. Three contrasting rain years (1994: excess year, 2001: normal year, 2002: deficient year) were selected and RegCM3 was integrated at 60 km horizontal resolution from April 1 to October 1 each year. The simulated fields of circulations and precipitation were validated against the observation from the NCEP/NCAR reanalysis products and Global Precipitation Climatology Centre (GPCC), respectively. The important results of RegCM3 simulations are (a) LLJ was slightly stronger and split into two branches during excess rain year over the Arabian Sea while there was no splitting during normal and deficient rain years, (b) huge anticyclone with single cell was noted during excess rain year while weak and broken into two cells in deficient rain year, (c) the simulated spatial distribution of precipitation was comparable to the corresponding observed precipitation of GPCC over large parts of India, and (d) the sensitivity experiment using NIMBUS-7 SMMR snow data indicated that precipitation was reduced mainly over the northeast and south Peninsular India with the introduction of 0.1 m of snow over the Tibetan region in April.

• Journal of the Korean earth science society
• /
• v.41 no.2
• /
• pp.137-146
• /
• 2020

A great number of geological research data have been produced by individually conducted researchers and then personally stored in domestic universities and research institutes. However, it is difficult to share data with other researchers owing to low and limited accessibility. The purpose of this study is to systematically establish metadata for inaccessible data, to manage them collectively and to provide opportunities for utilizing the data to those who require efficient research methods. Approximately 1,000 geological specimens (900 rocks and fossils, 100 thin sections) were gathered, along with their metadata such as high-resolution photographs, classification, name, owner, address, and geographical coordinates of the sample site, to establish their features. Additionally, 3D modeling data for 100 rocks and fossils were generated. On the basis of this study, it is possible for researchers to access and share crucial geological data that have a high potential to be lost and have been neglected in restricted spaces; by avoiding the wasted time, energy, and costs caused by repetitive collection of data, researchers may perform effective research and achieve qualified and competitive research results. Moreover, vulnerable and important geological data in the field can be protected from damage caused by indiscriminate, repetitive collection of specimens that have previously been secured. Through the establishment of additional metadata concerning the diversity of rocks, fossils, and thin sections kept at other universities and research institutes, much more data can be recognized, leading to advanced research results. Furthermore, specialized comparison and analysis of basic mineralogy and petrology knowledge are anticipated, based on the use of the metadata.

• Journal of Korean Society for Geospatial Information Science
• /
• v.12 no.4 s.31
• /
• pp.27-33
• /
• 2004

Recently, as a part of NGIS project, cultural-assets digital map is produced by cultural properties administration and local autonomous entities. Cultural-assets unified GIS(Geographic Information System) is essential to cultural properties managers md other organizations which are executing land related business for appling it at planning stage. With explosive national land developments, it has been obligated to implement surface survey by the cultural properties protection Art. In this paper, the authors used the district of Sachon city and made 3D terrain model using digital map which is made of 1/5000 stale. Moreover, the authors improved to RDBMS(Relational Database Management System) structure and remodeled the existing DB design in detail, and also tried recovery of past sea level, based on researches about the water level of southern area. By recover past sea level. the shell mound, apart from lever is actually near lever at past, and it make sure its nature. The authors suggested to realize shape and kind of remains which have 3D information of accuracy and actualization from surface-surveying to excavation.

• Spatial Information Research
• /
• v.16 no.1
• /
• pp.19-32
• /
• 2008

Usually in South Korea, land cover type and topographic undulation are frequently changed even in a narrow area. However, most of researches using aerial LIDAR(LIght Detection And Ranging) data in abroad had been acquired in the study areas to be changed infrequently. This research was performed to explore reconstruction methodologies of 3D surface models considering the distribution of land cover type and topographic undulation. Composed of variously undulatory forests, rocky river beds and man-made land cover such as streets, trees, buildings, parking lots and so on, an area was selected for the research. First of all, the area was divided into three zones based on land cover type and topographic undulation using its aerial ortho-photo. Then, aerial LIDAR data was clipped by each zone and different 3D modeling processes were applied to each clipped data before integration of each models and reconstruction of overall model. These kinds of processes might be effectively applied to landscape management, forest inventory and digital map composition. Besides, they would be useful to resolve less- or over-extracted problems caused by simple rectangle zoning when an usual data processing of aerial LIDAR.