• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.722-726
• /
• 2019

In this paper, we propose a low drop-out (LDO) regulator with improved power-supply rejection (PSR) characteristics in the high frequency region. In particular, an NMOS transistor with a high output resistance is added as a compensation circuit to offset the high frequency noise passing through the finite output resistance of the PMOS power switch. The elimination of power supply noise by the compensating transistor was explained analytically and presented as the direction for further improvement. The circuit was fabricated in a $0.35-{\mu}m$ standard CMOS process and Specter simulations were carried out to confirm the PSR improvement of 26 dB compared to the conventional LDO regulator at 10 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.4 s.95
• /
• pp.389-396
• /
• 2005

In this paper, we propose a pre-distortion method using the NLMS(Normalized Least Mean Square) algorithm to cope with hish PAPR(Peak to Average Power Ratio) problem in OFDM communication system. This proposed scheme estimates the distortion characteristics of HPA, and changes the characteristic against the distortion. Therefore, it can be shown that the adaptive characteristic of the NLMS pre-distorter is good to track the various nonlinear characteristic of HPA, even though HPA characteristic is changed by temperature variation or aging. From the performance analysis, SNR efficiency of NLMS pre-distorter is about $0.5\;\cal{dB}$ less than that of common numerical non-adaptive pre-distorter, when IBO(Input Back Off) is $0\;\cal{dB}$. However, the NLMS pre-distorter is better than the common numerical pre-distorter, because these two pre-distorters have similar performance in higher than $3\;\cal{dB}$ IBO, and the NLMS pre-distorter maintains the constant performance even though characteristic of HPA is changed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.484-491
• /
• 2002

This paper presents the results of a study of voltage-controlled PIN diode attenuators for Ku-band satellite payload and suggests the temperature-compensation method of these attenuators. The PIN diode attenuators are designed using thin-film hybrid techniques. The load resistance for maximum linear characteristics is determined by simulation and measurements. In the case of APD0805, load resistance of 150 $\Omega$ gives attenuator up to 10 dB linear attenuation range per a PIN diode. Also, measurements over temperature of these PIN diode attenuators were performed. From these measurements, designed PIN diode attenuators shows the severe temperature dependency due to forward voltage variation. A temperature compensation method using thermistor is now suggested to compensate the temperature variation of these PIN diode attenuators. This circuit shows good linear characteristics over wide temperature range

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.8
• /
• pp.29-39
• /
• 2015

This paper describes a design and implementation of fuzzy-based algorithm for hand-shake state detection and error compensation in the mobile optical image stabilization(OIS) motion detector. Since the gyro sensor output of the OIS motion detector includes inherent error signals, accurate error correction is required for prompt hand-shake error compensation and stable hand-shake state detection. In this research with a little computation overhead of fuzzy-based algorithm, the hand-shake error compensation could be improved by quickly reducing the angle and phase error for the hand-shake frequencies. Further, stability of the OIS system could be enhanced by the hand-shake states of {Halt, Little vibrate, Big vibrate, Pan/Tilt}, classified by subdividing the hand-shake angle. The performance and stability of the proposed algorithm in OIS motion detector is quantitatively and qualitatively evaluated with the emulated hand-shaking of ${\pm}0.5^{\circ}$, ${\pm}0.8^{\circ}$ vibration and 2~12Hz frequency. In experiments, the average error compensation gain of 3.71dB is achieved with respect to the conventional BACF/DCF algorithm; and the four hand-shake states are detected in a stable manner.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.12A
• /
• pp.1225-1232
• /
• 2008

In this paper, we describe a compensation method of diurnal effect which is one of the factors giving large effect on the performance when using ground-wave signals like Loran-C for a backup and substitute navigation system of global satellite navigation system such as GPS, and currently many researches of the topics are doing in USA and in Europe. In order to compensate diurnal effect, we find periodic frequency components by using the Least Square Spectral Analysis (LSSA) method at first and then compensate the effect by subtracting the estimated compensation signal, obtained by using the estimated amplitude and phase of the individual frequency component, from the original signal. In this paper, we propose a simple compensation algorithm and analysis the performance through simulations. From the results, it is observed that the amplitude and phase can be estimated with under 5 % and 0.17 % in a somewhat poor receiving situation with 0 dB Signal to Noise Ratio (SNR). Also, we analyze the obtainable performance improvement after compensation by using the measured Loran-C data. From the results, it is observed that we can get about 22 % performance improvement when a moving average with 5 minutes interval is employed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.7
• /
• pp.1187-1192
• /
• 2008

This paper proposes a fast motion estimation using an adaptive search region and a new three step search. The proposed method improved in the quality of motion compensation image as $0.43dB{\sim}2.19dB$, according as it predict motion of current block from motion vector of neigher blocks, and adaptively set up search region using predicted motion information. We show that the proposed method applied a new three step search pattern is able to fast motion estimation, according as it reduce computational complexity per blocks as $1.3%{\sim}1.9%$ than conventional method.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.7
• /
• pp.26-36
• /
• 2014

The needs of active phased arrays antenna system is getting more increased for IMT-Advanced system efficiency. The active phased array structure consists of lots of small transceivers and radiation elements to increase system efficiency. The minimized module of high efficiency transceiver is key for system implementation. The power amplifier of transmitter decides efficiency of base-station. In this paper, we design and implement minimized module of high efficiency transceiver for IMT-Advanced active phased array system. The temperature compensation circuit of transceiver reduces gain error and the analog pre-distorter of linearizer reduces implemented size. For minimal size and high efficiency, the implented power amplifier consist of GaN MMIC Doherty structure. The size of implemented module is $40mm{\times}90mm{\times}50mm$ and output power is 47.65 dBm at LTE band 7. The efficiency of power amplifier is 40.7% efficiency and ACLR compensation of linearizer is above 12dB at operating power level, 37dBm. The noise figure of transceiver is under 1.28 dB and amplitude error and phase error on 6 bit control is 0.38 dB and 2.77 degree respectively.

• Journal of Power Electronics
• /
• v.1 no.2
• /
• pp.65-70
• /
• 2001

Transmission System Operators are governed by operational security standards that are applied in real time. During system disturbances, the System Operators must rely on the installed protection and control equipment, prior to human intervention. New power electronic solutions bring rapid and repeatable responses to disturbances, which will help System Operators to guarantee a stable system. Last year, Alstom completed the world's first competitively bid STATCOM to support the voltage on National Grid's 400kV network that supplies London and the Southeast from the north of the UK. It is rated ${\pm}75MVAr$ and forms part of a Static Var System (SVS) with a total rating of 0 to 225MVAr. This paper will describe the reasons for its size, location, its chain-link configuration and give examples of its operating performance. The paper will also describe the features that allow this STATCOM to deliver much more than reactive compensation in support of a wider transmission service objective, as system conditions require.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.528-533
• /
• 2016

A low voltage high PSRR CMOS Bandgap circuit capable of generating a stable voltage of less than 1 V (0.8 V and 0.5 V) robust to Process, Voltage and Temperature (PVT) variations is proposed. The high PSRR of the circuit is guaranteed by a low-voltage current mode regulator at the central aspect of the bandgap circuitry, which isolates the bandgap voltage from power supply variations and noise. The isolating current mirrors create an internal regulated voltage $V_{reg}$ for the BG core and Op-Amp rather than the VDD. These current mirrors reduce the impact of supply voltage variations. The proposed circuit is implemented in a $0.35{\mu}m$ CMOS technology. The BGR circuit occupies $0.024mm^2$ of the die area and consumes $200{\mu}W$ from a 5 V supply voltage at room temperature. Experimental results demonstrate that the PSRR of the voltage reference achieved -118 dB at frequencies up to 1 kHz and -55 dB at 1 MHz without additional circuits for the curvature compensation. A temperature coefficient of $60 ppm/^{\circ}C$ is obtained in the range of -40 to $120^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.8
• /
• pp.759-765
• /
• 2005

In this paper, developed isolator for gap filler is analyzed and designed using the simulation tool. Using the designed parameters, isolator is fabricated and tested in gap filler band. Temperature characteristics of isolator depend on magnet, YIG ferrite, and conductor etc. These require temperature stability and possible method of compensation for the temperature dependent effects. The temperature stabilization tries to use Ni-alloy. Developed isolator that compare with room temperature and high temperature characteristics has change fewer than 20 MHz. Implemented isolator shows more than 20 dB isolation characteristic at center frequency(2,650 MHz) and has 0.2 dB insertion loss in overall 100 MHz operating bandwidth. Return losses of input and output port are measured below -20 dB.